gear switch NISSAN TEANA 2008 Workshop Manual

TM-294
< SYMPTOM DIAGNOSIS >[CVT: RE0F10A]
SYSTEM SYMPTOM
20
OthersVehicle does not de-
celerate by engine
brake.ON vehicle1. CVT fluid level and stateTM-304
2. CVT positionTM-314
3. CAN communication lineTM-208
4. Step motorTM-261
5. Primary speed sensorTM-218
6. Secondary speed sensorTM-222
7. Line pressure testTM-308
8. Engine speed signalTM-226
9. Accelerator pedal position sensorTM-252
OFF vehicle 10. Control valveTM-332
21 Maximum speed low.ON vehicle1. CVT fluid level and stateTM-304
2. Line pressure testTM-308
3. Accelerator pedal position sensorTM-252
4. CAN communication lineTM-208
5. Stall testTM-306
6. Step motorTM-261
7. Primary speed sensorTM-218
8. Secondary speed sensorTM-222
9. Secondary pressure sensorTM-242
10. CVT fluid temperature sensorTM-216
OFF vehicle11. Torque converterTM-335
12. Oil pump assembly
TM-332
13. Gear system
14. Forward clutch
15. Control valve
22With selector lever in
“P” position, vehicle
does not enter park-
ing condition or, with
selector lever in an-
other position, park-
ing condition is not
cancelled.ON vehicle1. PNP switchTM-213
2. CVT positionTM-314
OFF vehicle 3. Parking componentsTM-332
23Vehicle runs with CVT
in “P” position.ON vehicle1. PNP switchTM-213
2. CVT fluid level and stateTM-304
3. CVT positionTM-314
OFF vehicle4. Parking components
TM-3325. Gear system
6. Control valve No
.Item Symptom Condition Diagnostic Item Reference

SYSTEM SYMPTOM
TM-295
< SYMPTOM DIAGNOSIS >[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
24
OthersVehicle runs with CVT
in “N” position.ON vehicle1. PNP switchTM-213
2. CVT fluid level and stateTM-304
3. CVT positionTM-314
OFF vehicle4. Gear system
TM-3325. Forward clutch
6. Reverse brake
7. Control valve
25 Engine stall.ON vehicle1. CVT fluid level and stateTM-304
2. Engine speed signalTM-226
3. Primary speed sensorTM-218
4. Torque converter clutch solenoid valveTM-230
5. CAN communication lineTM-208
6. Stall testTM-306
7. Secondary pressure sensorTM-242
OFF vehicle8. Torque converterTM-3359. Control valveTM-332
26Engine stalls when
selector lever is shift-
ed “N”→“D” or “R”.ON vehicle1. CVT fluid level and stateTM-304
2. Engine speed signalTM-226
3. Primary speed sensorTM-218
4. Torque converter clutch solenoid valveTM-230
5. CAN communication lineTM-208
6. Stall testTM-306
OFF vehicle7. Torque converterTM-3358. Control valveTM-332
27Engine speed does
not return to idle.ON vehicle1. CVT fluid level and stateTM-304
2. Accelerator pedal position sensorTM-252
3. Secondary speed sensorTM-222
4. CAN communication lineTM-208
OFF vehicle 5. Control valveTM-332
28 CVT does not shift.ON vehicle1. CVT fluid level and stateTM-304
2. CVT positionTM-314
3. Line pressure testTM-308
4. Engine speed signalTM-226
5. Accelerator pedal position sensorTM-252
6. CAN communication lineTM-208
7. Primary speed sensorTM-218
8. Secondary speed sensorTM-222
9. Step motorTM-261
OFF vehicle10. Control valve
TM-33211. Oil pump assembly
29Engine does not start
in “N” or “P” position.ON vehicle1. Ignition switch and starterPG-55
,
STR-10
2. CVT positionTM-314
3. PNP switchTM-213
No
.Item Symptom Condition Diagnostic Item Reference

TM-312
< ON-VEHICLE MAINTENANCE >[CVT: RE0F10A]
ROAD TEST
Cruise Test
INFOID:0000000003806511
1.CHECK VEHICLE SPEED WHEN SHIFTING GEARS — PART 1
1. Drive vehicle for approximately 10 minutes to warm engine oil and CVT fluid up to operating temperature.
2. Park vehicle on flat surface.
3. Move selector lever to “P” position.
4. Start engine.
5. Move selector lever to “D” position.
6. Accelerate vehicle at 2/8 throttle opening and check “Vehicle
Speed When Shifting Gears”.
With CONSULT-III
- Read vehicle speed and engine speed. Refer to TM-337, "Vehi-
cle Speed When Shifting Gears".
Is the inspection results normal?
YES >> GO TO 2.
NO >> Refer to TM-286, "
Symptom Table". GO TO 2.
2.CHECK VEHICLE SPEED WHEN SHIFTING GEARS — PART 2
1. Park vehicle on flat surface.
2. Move selector lever to “D” position.
3. Accelerate vehicle at 8/8 throttle opening and check “Vehicle
Speed When Shifting Gears”.
With CONSULT-III
- Read vehicle speed and engine speed. Refer to TM-337, "Vehi-
cle Speed When Shifting Gears".
Is the inspection results normal?
YES >> GO TO 3.
NO >> Refer to TM-286, "
Symptom Table". GO TO 3.
3.CHECK SPORT MODE CONDITION (PART 1)
1. Park vehicle on flat surface.
2. Push sport mode switch. (Sport mode ON.)
3. Accelerate vehicle at 2/8 throttle opening and check “Vehicle
Speed When Shifting Gears”.
With CONSULT-III
- Read vehicle speed and engine speed. Refer to TM-337, "Vehi-
cle Speed When Shifting Gears".
Is the inspection results normal?
YES >> GO TO 4.
NO >> Refer to TM-286, "
Symptom Table". GO TO 4.
4.CHECK SPORT MODE CONDITION (PART 2)
1. Park vehicle on flat surface.CVT fluid operating temperature : 50 – 80°C (122 – 176°F)
SCIA6644E
SCIA4366E
SCIA6644E

ROAD TEST
TM-313
< ON-VEHICLE MAINTENANCE >[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
2. Accelerate vehicle at 8/8 throttle opening and check “Vehicle
Speed When Shifting Gears”.
With CONSULT-III
- Read vehicle speed and engine speed. Refer to TM-337, "Vehi-
cle Speed When Shifting Gears".
Is the inspection results normal?
YES >> GO TO 5.
NO >> Refer to TM-286, "
Symptom Table". GO TO 5.
5.CHECK “L” POSITION FUNCTION (PART 1)
1. Park vehicle on flat surface.
2. Move selector lever to “L” position.
3. Accelerate vehicle at 2/8 throttle opening and check “Vehicle
Speed When Shifting Gears”.
With CONSULT-III
- Read vehicle speed and engine speed. Refer to TM-337, "Vehi-
cle Speed When Shifting Gears".
Is the inspection results normal?
YES >> GO TO 6.
NO >> Refer to TM-286, "
Symptom Table". GO TO 6.
6.CHECK “L” POSITION FUNCTION (PART 2)
1. Park vehicle on flat surface.
2. Accelerate vehicle at 8/8 throttle opening and check “Vehicle
Speed When Shifting Gears”.
With CONSULT-III
- Read vehicle speed and engine speed. Refer to TM-337, "Vehi-
cle Speed When Shifting Gears".
Does it switch to manual mode?
YES >> GO TO 7.
NO >> Refer to TM-286, "
Symptom Table". GO TO 7.
7.CHECK ENGINE BRAKE FUNCTION
Check engine brake.
Does engine braking effectively reduce vehicle speed in
“L” position?
YES >> 1. Stop the vehicle.
2. Perform self-diagnosis. Refer to TM-204, "
CONSULT-III Function (TRANSMISSION)".
NO >> Refer to TM-286, "
Symptom Table". Then continue trouble diagnosis.
SCIA4366E
SCIA6644E
SCIA4366E