battery NISSAN TEANA 2008 Manual PDF

AV-234
< COMPONENT DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
U1298, U1299, U129A, U129B FRONT LEFT SQUAWKER
U1298, U1299, U129A, U129B FRONT LEFT SQUAWKER
DescriptionINFOID:0000000003901612
DTC LogicINFOID:0000000003901613
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000003901614
1.PERFORM THE SELF-DIAGNOSIS
1. Delete the self-diagnosis results. Turn ignition switch OFF.
2. Turn ignition switch ON. perform the self-diagnosis again.
3. Check that the DTC is detected again.
Is any DTC detected?
YES >> Repair sound signal front squawker LH circuit harness or connector.
NO >> Refer to GI section. Refer to GI-35, "
Intermittent Incident".
Part name Description
FRONT LEFT SQUAWKER Outputs sound signal from BOSE amp.
 Outputs sound (high and mid range).
DTCDisplay contents of
CONSULT-IIIDTC Detection Condition Possible causes
U1298FR-TWEETER OPEN
[U1298]Sound signal front squawker LH circuit is open.Check sound signal front squawker
LH circuit.
U1299FR-TWEETER SHORT
[U1299]Sound signal front squawker LH circuit is shorted between
front squawker LH signal (+) and front squawker LH signal
(-).Check sound signal front squawker
LH circuit.
U129AFR-TWEETER GND-
SHORT [U129A]Sound signal front squawker LH circuit to ground is short-
ed.Check sound signal front squawker
LH circuit.
U129BFR-TWEETER VB-
SHORT [U129B]Sound signal front squawker LH circuit to battery is short-
ed.Check sound signal front squawker
LH circuit.

AV-236
< COMPONENT DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
AV CONTROL UNIT
AV CONTROL UNIT : Diagnosis ProcedureINFOID:0000000003901178
1.CHECK FUSE
Check for blown fuses.
Is inspection result normal?
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT
Check voltage between AV control unit harness connectors and ground.
Is inspection result normal?
YES >> GO TO 3.
NO >> Check harness between AV control unit and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect AV control unit connectors.
3. Check continuity between AV control unit harness connectors and ground.
Is inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
DISPLAY UNIT
DISPLAY UNIT : Diagnosis ProcedureINFOID:0000000003901179
1.CHECK POWER SUPPLY CIRCUIT (DISPLAY SIDE)
Check voltage between display unit harness connector and ground.
Is inspection result normal?
YES >> GO TO 4.
NO >> GO TO 2.
Power source Fuse No.
Battery 31
Ignition switch ACC or ON 19
Ignition switch ON or START 4
Signal name Connector No. Terminal No. Ignition switch position Voltage (Approx.)
Battery power supply
M12719 OFF
Battery voltage ACC power supply 7 ACC
Ignition signal M131 104 ON
Signal name Connector No. Terminal No. Ignition switch position Continuity
GroundM127 20
OFF Existed
M131 85
Signal name Connector No. Terminal No. Ignition switch position Voltage (Approx.)
Inverter VCC
M492
ACC 9 V
Signal VCC 3

AV-238
< COMPONENT DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
POWER SUPPLY AND GROUND CIRCUIT
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT
Check voltage between multifunction switch harness connector and ground.
Is inspection result normal?
YES >> GO TO 3.
NO >> Check harness between multifunction switch and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect multifunction switch connector.
3. Check continuity between multifunction switch harness connector and ground.
Is inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
BOSE AMP.
BOSE AMP. : Diagnosis ProcedureINFOID:0000000003901182
1.CHECK FUSE
Check for blown fuses.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT
Check voltage between BOSE amp. harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check harness between BOSE amp. and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BOSE amp. connector.
3. Check continuity between BOSE amp. harness connector and ground.
Signal name Connector No. Terminal No. Ignition switch position Voltage (Approx.)
ACC power supply M125 3 ACC Battery voltage
Signal name Connector No. Terminal No. Ignition switch position Continuity
Ground M125 1 OFF Existed
Power source Fuse No.
Battery 32, 33
Ignition switch ACC 19
Signal name Connector No. Terminal No. Ignition switch position Voltage (Approx.)
Battery power supply B22410
OFF
Battery voltage 11
ACC power supply B225 20 ACC

AV
POWER SUPPLY AND GROUND CIRCUIT
AV-239
< COMPONENT DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
CAMERA CONTROL UNIT
CAMERA CONTROL UNIT : Diagnosis ProcedureINFOID:0000000003901183
1.CHECK FUSE
Check for blown fuses.
Is inspection result normal?
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUITS
Check voltage between camera control unit harness connector and ground.
Is inspection result normal?
YES >> GO TO 3.
NO >> Check harness between camera control unit and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect camera control unit connector.
3. Check continuity between camera control unit harness connector and ground.
Is inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
DVD PLAYER
DVD PLAYER : Diagnosis ProcedureINFOID:0000000003901184
1.CHECK FUSE
Check for blown fuses.
Is inspection result normal?
Signal name Connector No. Terminal No. Ignition switch position Continuity
Ground B2247
OFF Existed
12
Power source Fuse No.
Battery 31
Ignition switch ACC 19
Signal name Connector No. Terminal No. Ignition switch position Voltage (Approx.)
Battery power supply
B25132 OFF
Battery voltage
ACC power supply 30 ACC
Signal name Connector No. Terminal No. Ignition switch position Continuity
Ground B251 31 OFF Existed
Power source Fuse No.
Battery 31
Ignition switch ACC or ON 19

AV-240
< COMPONENT DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
POWER SUPPLY AND GROUND CIRCUIT
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT
Check voltage between DVD player harness connectors and ground.
Is inspection result normal?
YES >> GO TO 3.
NO >> Check harness between DVD player and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect DVD player connectors.
3. Check continuity between DVD player harness connectors and ground.
Is inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
Signal name Connector No. Terminal No. Ignition switch position Voltage (Approx.)
Battery power supply
M2542OFF
Battery voltage
ACC power supply 4 ACC
Signal name Connector No. Terminal No. Ignition switch position Continuity
Ground M254 1 OFF Existed

AV
AV CONTROL UNIT
AV-261
< ECU DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
ECU DIAGNOSIS
AV CONTROL UNIT
Reference ValueINFOID:0000000003765757
VALUES ON THE DIAGNOSIS TOOL
CONSULT-III data monitor item
TERMINAL LAYOUT
PHYSICAL VALUES
Display ItemDis-
playVehicle status Remarks
VHCL SPD SIGOn Vehicle speed >0 km/h (0 MPH)
Changes in indication may be delayed. This is nor-
mal.
Off Vehicle speed =0 km/h (0 MPH)
PKB SIGOn Parking brake is applied.
Changes in indication may be delayed. This is nor-
mal.
Off Parking brake is released.
ILLUM SIGOn Light switch ON.
—
Off Light switch OFF.
IGN SIGOn Ignition switch ON.
—
Off Ignition switch in ACC position.
REV SIGOn Selector lever in R position.
Changes in indication may be delayed. This is nor-
mal.
OffSelector lever in any position other
than R.
JPNIA1093ZZ
Te r m i n a l
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
6
(W/G)15
(L/B)Steering switch signal A InputIgnition
switch
ONKeep pressing SOURCE
switch. 0 V
Keep pressing switch.0.7 V
Keep pressing switch.1.3 V
Except for above. 3.3 V
7
(V/W)Ground ACC power supply InputIgnition
switch
ACC— Battery voltage
9
(R/L)Ground Illumination signal InputIgnition
switch
OFFLighting switch is OFF. 0 V
Lighting switch is ON. 12.0 V

AV-262
< ECU DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
AV CONTROL UNIT
15
(L/B)GroundSteering switch signal
ground—Ignition
switch
ON—0 V
16
(GR/L)15
(L/B)Steering switch signal B InputIgnition
switch
ONKeep pressing VOL DOWN
switch.0 V
Keep pressing VOL UP
switch.0.7 V
Except for above. 3.3 V
19
(Y)Ground Battery power supply InputIgnition
switch
OFF— Battery voltage
20
(B/W)Ground Ground —Ignition
switch
ON—0 V
33 — FM sub Input — — —
34 — AM–FM main Input — — —
35 Ground Antenna amp. ON signal OutputIgnition
switch
ACC— 12.0 V
36
(B)Ground Composite image signal OutputIgnition
switch
ONWhen camera image, DVD
image or AUX image is dis-
played.
37
(W)GroundComposite image signal
ground—Ignition
switch
ON—0 V
38
(B)Ground RGB image signal (B: blue) OutputIgnition
switch
ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
39
(R)GroundRGB image signal (G:
green)OutputIgnition
switch
ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen. Terminal
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIB2251J
SKIB2237J
SKIB2236J

AV
AV CONTROL UNIT
AV-265
< ECU DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P83
(R)82
(W)Stereo (DVD and AUX)
sound signal RHInputIgnition
switch
ONDVD* and AUX sound out-
put.
85
(B/W)Ground Ground —Ignition
switch
ON —0 V
86
(L)—CAN–HInput/
Output—— —
87
(P)—CAN–LInput/
Output—— —
88
(W)—AV communication signal
(H)Input/
Output—— —
89
(B)—AV communication signal
(L)Input/
Output—— —
90
(L)—AV communication signal
(H)Input/
Output—— —
91
(R)—AV communication signal
(L)Input/
Output—— —
99
(B)98
(G)Stereo (DVD and AUX)
sound signal LHInputIgnition
switch
ONDVD
*or AUX sound output.
100 — Shield — — — —
101
(BR)Ground Switch ground —Ignition
switch
ON—0 V
103
(SB)Ground Disk eject signal InputIgnition
switch
ONPressing the eject switch. 0 V
Except for above. 3.3 V
104
(O)Ground Ignition signal InputIgnition
switch
ON— Battery voltage
105
(P/B)Ground Reverse signal InputIgnition
switch
ONSelector lever in R position. 12.0 V
Other than selector lever in
R position.0 V Te r m i n a l
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIB3609E
SKIB3609E

AV-308
< ECU DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
BOSE AMP.
BOSE AMP.
Reference ValueINFOID:0000000003793619
TERMINAL LAYOUT
PHYSICAL VALUES
JPNIA1094ZZ
Te r m i n a l
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
1
(LG)2
(V)Sound signal front squawk-
er LHOutputIgnition
switch
ONAudio output
4
(P)3
(L)Sound signal front squawk-
er RHOutputIgnition
switch
ONAudio output
5
(Y)6
(BR)Sound signal woofer RH OutputIgnition
switch
ONAudio output
7
(B)Ground Ground —Ignition
switch
ON—0 V
10
(SB)Ground Battery power supply InputIgnition
switch
OFF— Battery voltage
11
(GR)Ground Battery power supply InputIgnition
switch
OFF— Battery voltage
12
(B)Ground Ground —Ignition
switch
ON—0 V
SKIB3609E
SKIB3609E
SKIB3609E

AV-330
< ECU DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
DVD PLAYER
DVD PLAYER
Reference ValuesINFOID:0000000003793618
TERMINAL LAYOUT
PHYSICAL VALUES
JPNIA1095ZZ
Terminal
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
1
(B/W)Ground Ground —Ignition
switch
ON—0 V
2
(Y)Ground Battery power supply InputIgnition
switch
OFF— Battery voltage
3
(R/L)Ground Illumination signal InputIgnition
switch
OFFLighting switch is OFF. 0 V
Lighting switch is ON. 12.0 V
4
(V/W)Ground ACC power supply InputIgnition
switch
ACC— Battery voltage
5—Shield —— — —
6—Shield —— — —
7
(V)GroundComposite (DVD and AUX)
image signalOutputIgnition
switch
ONWhen DVD image or AUX
image is displayed.
8
(G)GroundComposite (AUX) image
signalOutputIgnition
switch
ONWhen AUX image is dis-
played.
9
(G)GroundComposite (DVD and AUX)
image signal ground—Ignition
switch
ON—0 V
10
(V)GroundComposite image (AUX)
signal ground—Ignition
switch
ON—0 V
SKIB2251J
SKIB2251J