camera NISSAN TEANA 2008 Manual Online

AV-206
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Select “SPEAKER DIAGNOSIS” to display the Speaker Diagnosis
screen. Press “START and NEXT” to generate a test tone in a
speaker. Press “Start” to generate a test tone in the next speaker.
Press “End” to stop the test tones.
NOTE:
The frequency of test tone emitted from each speaker is as follows.
Climate Control
On-board self-diagnosis is not supported. Only CONSULT-III is supported.
Refer to HAC-156, "
WITHOUT INTELLIGENT AIR CONDITIONER SYSTEM : CONSULT-III Function" for
details.
Camera Cont.
Refer to AV-196, "System Description".
Error History
The self-diagnosis results are judged depending on whether any error occurs from when “Self-diagnosis” is
selected until the self-diagnosis results are displayed.
However, the diagnosis results are judged normal if an error has occurred before the ignition switch is turned
ON and then no error has occurred until the self-diagnosis start. Check the “Error Record” to detect any error
that may have occurred before the self-diagnosis start because of this situation.
The error record displays the time and place of the most recent occurrence of that error. However, take note of
the following points.
 Place of the error occurrence is represented by the position of the current location mark at the time an error
occurred. If current location mark has deviated from the correct position, then the place of the error occur-
rence cannot be located correctly.
 The frequency of occurrence is displayed in a count up manner. The actual count up method differs depend-
ing on the error item.
Count up method A
 The counter resets to 0 if an error occurs when IGN switch is turned ON. The counter increases by 1 if the
condition is normal at a next IGN ON cycle.
 The counter upper limit is 39. Any counts exceeding 39 are ignored.“ The counter can be reset (no error
record display) with the “Delete log” switch or CONSULT-III.
Count up method B
 The counter increases by 1 if an error occurs when IGN switch is ON. The counter will not decrease even if
the condition is normal at the next IGN ON cycle.
 The counter upper limit is 50. Any counts exceeding 50 are ignored. “ The counter can be reset (no error
record display) with the “Delete log” switch or CONSULT-III.Squawker : 3 kHz
Front speaker : 300 Hz
Rear speaker : 1 kHz
JSNIA0150GB
Display type of occur-
rence frequencyError history display item
Count up method A CAN communication line, control unit (CAN), AV communication line, control unit (AV communication)
Count up method B Other than the above

AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-207
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Error item
Some error items may be displayed simultaneously according to the cause. If some error items are displayed
simultaneously, the detection of the cause can be performed by the combination of display items
JSNIA0151GB
Error item Description Possible malfunction factor/Action to take
CAN COMM CIRCUITCAN communication malfunction is detect-
ed.Perform diagnosis with CONSULT-III, and
then repair the malfunctioning parts accord-
ing to the diagnosis results.
CONTROL UNIT (CAN)CAN initial diagnosis malfunction is detect-
ed.
Replace the AV control unit. CONTROL UNIT (AV)AV communication circuit initial diagnosis
malfunction is detected.
FLASH-ROM Error Of Control Unit
AV control unit malfunction is detected.
CAN Controller Memory Error
Amplifier Temperature Error BOSE amp. malfunction is detected. Replace the BOSE amp.
Front Display Connection ErrorWhen either one of the following items is
detected:
 display unit power supply and ground cir-
cuits are malfunctioning.
 serial communication circuits between
display unit and AV control unit are mal-
functioning.
 serial communication signal between
display unit and AV control unit is mal-
functioning. Display unit power supply and ground
circuits.
 Serial communication circuits between
display unit and AV control unit.
Camera Cont. Unit Connection ErrorA malfunction is detected in camera con-
nection recognition signal circuit.Camera connection recognition signal cir-
cuit.
Center speaker OUT: openSound signal center speaker circuit is
open.Check sound signal center speaker circuit.
Center speaker OUT: shortSound signal center speaker circuit is
shorted between center speaker signal (+)
and center speaker signal (-).Check sound signal center speaker circuit.
Center speaker OUT: short to groundSound signal center speaker circuit to
ground is shorted.Check sound signal center speaker circuit.
Center speaker OUT: short to batterySound signal center speaker circuit to bat-
tery is shorted.Check sound signal center speaker circuit.
FR speaker OUT: openSound signal front speaker RH circuit is
open.Check sound signal front speaker RH cir-
cuit.

AV-210
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Vehicle CAN Diagnosis
 CAN communication status and error counter is displayed.
 The error counter displays "OK" if any malfunction was not
detected in the past and displays "0" if a malfunction is detected. It
increases by 1 if the condition is normal at the next ignition switch
ON cycle. The upper limit of the counter is 39.
 The error counter is erased if reset.
AV COMM Diagnosis
 Displays the communication status between AV control unit (mas-
ter unit) and each unit.
 The error counter displays "OK" if any malfunction was not
detected in the past and displays "0" if a malfunction is detected. It
increases by 1 if the condition is normal at the next ignition switch
ON cycle. The upper limit of the counter is 39.
 If it resets, the error counter is erased.
 AV COMM CIRCUIT
 DVD Deck Connection Error
 Amplifier Connection Error
 Rear view Camera connection ErrorWith rear control switch
When either one of the following items is
detected:
 malfunction is detected in AV communi-
cation circuits between rear control
switch and camera control unit.
 malfunction is detected in AV communi-
cation circuits between camera control
unit and NAVI control unit.  AV communication circuits between mul-
tifunction switch and rear control switch.
 AV communication circuits between rear
control switch and camera control unit.
Without rear control switch
When either one of the following items is
detected:
 malfunction is detected in AV communi-
cation circuits between multifunction
switch and camera control unit.
 malfunction is detected in AV communi-
cation circuits between camera control
unit and NAVI control unit.AV communication circuits between multi-
function switch and camera control unit.
 AV COMM CIRCUIT
 Switches Connection Error
 DVD Deck Connection Error
 Amplifier Connection Error
 Rear view Camera connection ErrorWhen either one of the following items is
detected:
 AV communication circuits between AV
control unit and multifunction switch are
malfunctioning.
 AV communication signal between AV
control unit and multifunction switch is
malfunctioning.AV communication circuits between AV
control unit and multifunction switch. Error item Description Possible malfunction factor/Action to take
Items Display (Current)Malfunction counter
(Past)
Tx (HVAC) OK / UNKWN OK / 0 – 39
Rx (ECM) OK / UNKWN OK / 0 – 39
Rx (Cluster) OK / UNKWN OK / 0 – 39
Rx (BCM) OK / UNKWN OK / 0 – 39
Rx (HVAC) OK / UNKWN OK / 0 – 39
Rx (USM) OK / UNKWN OK / 0 – 39
JSNIA1287GB
ItemsStatus
(Current)Counter
(Past)
C Tx(ITM–SW) OK / UNKWN OK / 0 – 39
C Rx(PrimarySW–ITM) OK / UNKWN OK / 0 – 39
JSNIA1288GB

AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-211
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P Delete Unit Connection Log
Deletes any unit connection records and error records from the AV
control unit memory. (Clear the records of the unit that has been
removed)
CONSULT-III Function (MULTI AV)INFOID:0000000003765658
CONSULT-III FUNCTIONS
CONSULT-III performs the following functions via the communication with the AV control unit.
AV COMMUNICATION
When “AV communication” of “CAN Diag Support Monitor” is selected, the following function will be performed.
SELF-DIAGNOSIS RESULTS
 In CONSULT-III self-diagnosis, self-diagnosis results and error history are displayed collectively.
 The timing is displayed as “0” if any of the error codes [U1000], [U1010], [U1300] and [U1310] is detected.
The counter increases by 1 if the condition is normal at the next ignition switch ON cycle.
Self-diagnosis Results Display Item
C Rx(RrSeatSW–ITM) OK / UNKWN OK / 0 – 39
C Rx(Amp–ITM) OK / UNKWN OK / 0 – 39
C Rx(RearCamera–ITM) OK / UNKWN OK / 0 – 39
C Rx(DVD–ITM) OK / UNKWN OK / 0 – 39
C Rx(AmpAudio–ITM) OK / UNKWN OK / 0 – 39
C Rx(DVDAudio–ITM) OK / UNKWN OK / 0 – 39ItemsStatu s
(Current)Counter
(Past)
JSNIA0154GB
Diagnosis mode Description
Ecu Identification The part number of AV control unit can be checked.
Self Diagnostic ResultPerforms a diagnosis on the AV control unit and a connection diagnosis for the communication
circuit of the Multi AV system, and displays the current and past malfunctions collectively.
Data Monitor The diagnosis of vehicle signal that is input to the AV control unit can be performed.
AV communicationAV&NAVI C/UDisplays the communication status from AV control unit to each unit as well as the error
counter.
AUDIO Displays the AV control unit communication status and the error counter.
Error item Detection logic Possible malfunction factor/Action to take
CAN COMM CIRCUIT [U1000]CAN communication malfunction is detect-
ed.Refer to AV- 2 1 6 , "
DiagnosisProcedure".
CONTROL UNIT (CAN) [U1010]CAN initial diagnosis malfunction is detect-
ed.
Replace the AV control unit.
Refer toAV- 3 7 8 , "
Removal and Installation"
AV- 3 7 8 , "
Removal and Installation". CONTROL UNIT (AV) [U1310]AV communication circuit initial diagnosis
malfunction is detected.
Control Unit FLASH-ROM [U1200]
AV control unit malfunction is detected.
CAN CONT [U1216]

AV-212
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AMP TEMP [U1231] BOSE amp. is detected.Replace the BOSE amp.
Refer to AV- 3 8 6 , "Removal and Installa-
tion".
FRONT DISP CONN [U1243]When either one of the following items is
detected:
 display unit power supply and ground cir-
cuits are malfunctioning.
 serial communication circuits between
display unit and AV control unit are mal-
functioning.
 serial communication signal between
display unit and AV control unit is mal-
functioning. Display unit power supply and ground
circuits
Refer to AV- 2 2 2 , "
Diagnosis Procedure".
 Serial communication circuits between
display unit and AV control unit
CAMERA CONT. CONN [U1250]Camera connection recognition signal cir-
cuit malfunction is detected.Camera connection recognition signal cir-
cuit
Refer to AV- 2 2 4 , "
Diagnosis Procedure".
CENTER SP OPEN [U1260]Sound signal center speaker circuit is
open.Check sound signal center speaker circuit.
CENTER SP SHORT [U1261]Sound signal center speaker circuit is
shorted between center speaker signal (+)
and center speaker signal (-).Check sound signal center speaker circuit.
CENTER SP GND-SHORT [U1262]Sound signal center speaker circuit to
ground is shorted.Check sound signal center speaker circuit.
CENTER SP VB-SHORT [U1263]Sound signal center speaker circuit to bat-
tery is shorted.Check sound signal center speaker circuit.
FR-DOOR SP OPEN [U1264]Sound signal front speaker RH circuit is
open.Check sound signal front speaker RH cir-
cuit.
FR-DOOR SP SHORT [U1265]Sound signal front speaker RH circuit is
shorted between front speaker RH signal
(+) and front speaker RH signal (-).Check sound signal front speaker RH cir-
cuit.
FR-DOOR SP GND-SHORT [U1266]Sound signal front speaker RH circuit to
ground is shorted.Check sound signal front speaker RH cir-
cuit.
FR-DOOR SP VB-SHORT [U1267]Sound signal front speaker RH circuit to
battery is shorted.Check sound signal front speaker RH cir-
cuit.
RR-SP/FR-WOOFER OPEN [U1268]Sound signal rear speaker RH circuit is
open.Check sound signal rear speaker RH cir-
cuit.
RR-SP/FR-WOOFER SHORT [U1269]Sound signal rear speaker RH circuit is
shorted between rear speaker LH signal (+)
and rear speaker LH signal (-).Check sound signal rear speaker RH cir-
cuit.
RR-SP/FR-WOOFER GND-SHORT
[U126A]Sound signal rear speaker RH circuit to
ground is shorted.Check sound signal rear speaker RH cir-
cuit.
RR-SP/FR-WOOFER VB-SHORT [U126B]Sound signal rear speaker RH circuit to bat-
tery is shorted.Check sound signal rear speaker RH cir-
cuit.
RR-SURROUND SP OPEN [U126C] Sound signal woofer RH circuit is open. Check sound signal woofer RH circuit.
RR-SURROUND SP SHORT [U126D]Sound signal woofer RH circuit is shorted
between woofer RH signal (+) and woofer
RH signal (-).Check sound signal woofer RH circuit.
RR-SURROUND SP GND-SHORT
[U126E]Sound signal woofer RH circuit to ground is
shorted.Check sound signal woofer RH circuit.
RR-SURROUND SP VB-SHORT [U126F]Sound signal woofer RH circuit to battery is
shorted.Check sound signal woofer RH circuit.
RL-SURROUND SP OPEN [U1274] Sound signal woofer LH circuit is open. Check sound signal woofer LH circuit.
RL-SURROUND SP SHORT [U1275]Sound signal woofer LH circuit is shorted
between woofer LH signal (+) and woofer
LH signal (-).Check sound signal woofer LH circuit. Error item Detection logic Possible malfunction factor/Action to take

AV-214
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
DATA MONITOR
ALL SIGNALS
 Displays the status of the following vehicle signals inputted to the AV control unit.
 AV COMM CIRCUIT [U1300]
 AMP CONN [U124E]When either one of the following items is
detected:
 BOSE amp. power supply and ground
circuits are malfunctioning.
 AV communication signal between AV
control unit and BOSE amp. is malfunc-
tioning.BOSE amp. power supply and ground cir-
cuits
Refer to AV- 2 3 8 , "
BOSE AMP. : Diagnosis
Procedure".
 AV COMM CIRCUIT [U1300]
 DVD DECK CONN [U1248]When either one of the following items is
detected:
 DVD player power supply and ground cir-
cuits are malfunctioning.
 AV communication circuits between
BOSE amp. and DVD player are mal-
functioning.
 AV communication signal between AV
control unit and DVD player is malfunc-
tioning. DVD player power supply and ground cir-
cuits
Refer to AV- 2 3 9 , "
DVD PLAYER : Diag-
nosis Procedure"
 AV communication circuits between
BOSE amp. and DVD player
 AV COMM CIRCUIT [U1300]
 AMP CONN [U1252]When either one of the following items is
detected:
 camera control unit power supply and
ground circuits are malfunctioning.
 AV communication signal between AV
control unit and Camera control unit is
malfunctioning.Camera control unit power supply and
ground circuits
Refer to AV- 2 3 9 , "
CAMERA CONTROL
UNIT : Diagnosis Procedure".
 AV COMM CIRCUIT [U1300]
 DVD DECK CONN [U1248]
 AMP CONN [U124E]When either one of the following items is
detected:
 AV communication circuits between cam-
era control unit and BOSE amp. are mal-
functioning.
 AV communication signal between AV
control unit and BOSE amp. is malfunc-
tioning.AV communication circuits between cam-
era control unit and BOSE amp.
 AV COMM CIRCUIT [U1300]
 DVD DECK CONN [U1248]
 AMP CONN [U124E]
 REAR-CAMERA LAN CONN [U1252]With rear control switch
When either one of the following items is
detected:
 malfunction is detected in AV communi-
cation circuits between rear control
switch and camera control unit.
 malfunction is detected in AV communi-
cation circuits between camera control
unit and NAVI control unit.  AV communication circuits between mul-
tifunction switch and rear control switch
 AV communication circuits between rear
control switch and camera control unit
Without rear control switch
When either one of the following items is
detected:
 malfunction is detected in AV communi-
cation circuits between multifunction
switch and camera control unit.
 malfunction is detected in AV communi-
cation circuits between camera control
unit and NAVI control unit.AV communication circuits between multi-
function switch and camera control unit
 AV COMM CIRCUIT [U1300]
 SWITCH CONN [U1240]
 DVD DECK CONN [U1248]
 AMP CONN [U124E]
 REAR-CAMERA LAN CONN [U1252]When either one of the following items is
detected:
 AV communication circuits between AV
control unit and multifunction switch are
malfunctioning.
 AV communication signal between AV
control unit and multifunction switch is
malfunctioning.AV communication circuits between AV
control unit and multifunction switch Error item Detection logic Possible malfunction factor/Action to take

AV-218
< COMPONENT DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
U1310 AV CONTROL UNIT
U1310 AV CONTROL UNIT
DescriptionINFOID:0000000003765667
Replace the AV control unit if this DTC is displayed. Refer to AV-378, "Removal and Installation".
DTC LogicINFOID:0000000003765668
DTC DETECTION LOGIC
Part name Description
AV CONTROL UNIT It is the master unit of the MULTI AV system, and it is connected to each control
unit by communication. It operates each system according to communication
signals from the AV control unit.
 AV control unit includes audio function and vehicle information function.
 It is connected to ECM and combination meter. via CAN communication to ob-
tain necessary information for the vehicle information function.
 It is connected to BCM via CAN communication transmitting/receiving for the
vehicle settings function.
 Composite image signal (AUX and DVD images) is input from DVD player.
 Camera image signal is input from camera control unit.
 Composite image (DVD, AUX and camera images) signal is output to display
unit.
 Sound signal (DVD and AUX sounds) is input from the DVD player.
 Power (signal VCC and inverter VCC) is transmitted to front display unit.
DTCDisplay contents of
CONSULT-IIIDTC Detection Condition Action to take
U1310CONTROL UNIT (AV)
[U1310]AV communication circuit initial diagnosis malfunction is
detected.Replace AV control unit.

AV
U1200 AV CONTROL UNIT
AV-219
< COMPONENT DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
U1200 AV CONTROL UNIT
DescriptionINFOID:0000000003765669
Replace the AV control unit if this DTC is displayed. Refer to AV-378, "Removal and Installation".
DTC LogicINFOID:0000000003765670
DTC DETECTION LOGIC
Part name Description
AV CONTROL UNIT It is the master unit of the MULTI AV system, and it is connected to each control
unit by communication. It operates each system according to communication
signals from the AV control unit.
 AV control unit includes audio function and vehicle information function.
 It is connected to ECM and combination meter. via CAN communication to ob-
tain necessary information for the vehicle information function.
 It is connected to BCM via CAN communication transmitting/receiving for the
vehicle settings function.
 Composite image signal (AUX and DVD images) is input from DVD player.
 Camera image signal is input from camera control unit.
 Composite image (DVD, AUX and camera images) signal is output to display
unit.
 Sound signal (DVD and AUX sounds) is input from the DVD player.
 Power (signal VCC and inverter VCC) is transmitted to front display unit.
DTCDisplay contents of
CONSULT-IIIDTC Detection Condition Action to take
U1200Cont Unit
FLASH- ROM
[U1200]AV control unit malfunction is detected. (FLASH-ROM). Replace AV control unit.

AV-220
< COMPONENT DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
U1216 AV CONTROL UNIT
U1216 AV CONTROL UNIT
DescriptionINFOID:0000000003765671
Replace the AV control unit if this DTC is displayed. Refer to AV-378, "Removal and Installation".
DTC LogicINFOID:0000000003765672
Part name Description
AV CONTROL UNIT It is the master unit of the MULTI AV system, and it is connected to each control
unit by communication. It operates each system according to communication
signals from the AV control unit.
 AV control unit includes audio function and vehicle information function.
 It is connected to ECM and combination meter. via CAN communication to ob-
tain necessary information for the vehicle information function.
 It is connected to BCM via CAN communication transmitting/receiving for the
vehicle settings function.
 Composite image signal (AUX and DVD images) is input from DVD player.
 Camera image signal is input from camera control unit.
 Composite image (DVD, AUX and camera images) signal is output to display
unit.
 Sound signal (DVD and AUX sounds) is input from the DVD player.
 Power (signal VCC and inverter VCC) is transmitted to front display unit.
DTCDisplay contents of
CONSULT-IIIDTC Detection Condition Action to take
U1216CAN CONT
[U1216]Internal malfunction of AV control unit (CAN controller) is
detected.Replace AV control unit.

AV-222
< COMPONENT DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
U1243 DISPLAY UNIT
U1243 DISPLAY UNIT
DescriptionINFOID:0000000003765673
DTC LogicINFOID:0000000003765674
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000003901175
1.CHECK DISPLAY UNIT POWER SUPPLY AND GROUND CIRCUIT
Check display unit power supply and ground circuit. Refer to AV-236, "
DISPLAY UNIT : Diagnosis Procedure".
Is inspection result normal?
YES >> GO TO 2.
NO >> Repair malfunctioning parts.
2.CHECK CONTINUITY COMMUNICATION CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector and AV control unit connector.
3. Check continuity between display unit harness connector and AV control unit harness connector.
4. Check continuity between display unit harness connector and ground.
Is inspection result normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
Part name Description
DISPLAY UNIT Display image is controlled by the serial communication from AV control unit.
 It receives the power (signal VCC and inverter VCC) from the AV control unit
and operates.
 RGB image signal is input from AV control unit (RGB, RGB area and RGB syn-
chronizing).
 Composite image (DVD, AUX and camera images) signal is input from AV con-
trol unit.
 Synchronize signal (HP, VP) is output to AV control unit.
DTCDisplay contents of
CONSULT-IIIDTC Detection Condition Possible causes
U1243FRONT DISP CONN
[U1243]When either one of the following items is detected:
 display unit power supply and ground circuits are mal-
functioning.
 serial communication circuits between display unit and
AV control unit are malfunctioning.
 serial communication signal between display unit and
AV control unit is malfunctioning. Display unit power supply and
ground circuits.
 Serial communication circuits be-
tween display unit and AV control
unit
Display unit AV control unit
Continuity
Connector Terminals Connector Terminals
M4911
M12956
Existed
22 44
Display unit
GroundContinuity
Connector Terminals
M4911
Not existed
22