engine coolant NISSAN TEANA 2014 Service Manual

P2610 ECM INTERNAL TIMEREC-495
< DTC/CIRCUIT DIAGNOSIS > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-495, "Diagnosis Procedure".
NO >> GO TO 6.
6.PERFORM DTC CONFIRMATION PROCEDURE-II
CAUTION:
To start this self-diagnosis, the cond itions listed bellow are required to be satisfied. Perform the fol-
lowing steps to satisfy the conditions.
• Engine coolant temperature decrease by 55 °C (131 °F) or more during the time between an ignition
switch OFF (after engine warm-up) and the second ignition switch ON.
• A fuel temperature at the seco nd ignition switch ON is −5 °C (23 °F) or more and less than 35 °C (95 °F).
• The temperature difference between engine coolant and fuel is 5°C (41 °F) or more.
NOTE:
This self-diagnosis is not performed if the distance traveled is extremely short.
1. Turn ignition switch ON.
2. Start engine and warm it up to normal operating temperature.
3. Turn ignition switch OFF and soak the vehicle for at least 12 hours. CAUTION:
• Never turn ON the ignition switch during soaking.
• Never open the fuel filler cap an d perform refueling during soaking.
4. Turn ignition switch ON and wait at least 190 seconds.
5. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-495, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000009462427
1.CHECK SELF-DIAGNOSTIC RESULT
check that DTCs related to the fuel sy stem and the cooling system are not detected.
Is the inspection result normal?
YES >> Check the DTC. Refer to EC-77, "CONSULT Function".
NO >> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Erase DTC.
2. Perform DTC Confirmation Procedure again. Refer to EC-494, "DTC Logic"
.
Is the 1st trip DTC P2610 displayed again?
YES >> Replace ECM. Refer to EC-540, "Removal and Installation".
NO >> INSPECTION END
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-528
< SYMPTOM DIAGNOSIS >[QR25DE]
ENGINE CONTROL SYSTEM
Mass air flow sensor circuit
1
12 2
222 2 EC-228,
EC-232
Intake air temperature sensor circuit EC-240,
EC-241
Engine coolant temperature sensor circuit
333
EC-245,
EC-251
Air fuel ratio (A/F) sensor 1 circuit EC-258
,
EC-262
,
EC-265
,
EC-289
,
EC-468
Throttle position sensor circuit
22EC-248
,
EC-315
,
EC-426
,
EC-427
,
EC-488
Accelerator pedal position sensor circuit 3 2 1 EC-482
,
EC-485
,
EC-491
Heated oxygen sensor 2 circuit 6 6 6 6 5 EC-268
,
EC-276
,
EC-284
Knock sensor circuit 2 3 EC-324
Engine oil temperature sensor circuit 4 2 3EC-311,
EC-312
Engine oil pressure sensor circuit 4 4 3 3 3 3 EC-388,
EC-392
Crankshaft position sensor (POS) circuit 2 2 EC-326
Camshaft position sensor (PHASE) circuit 3 2EC-329
Vehicle speed signal circuit 2 3 3 3EC-380
ECM 22333333333EC-400
,
EC-401
,
EC-402
,
EC-404
Intake valve timing control solenoid valve cir-
cuit 32 13223 3 EC-209,
EC-221
Intake valve timing intermediate lock control
solenoid valve circuit EC-394
SYMPTOM
Reference page
HARD/NO START/RESTART (EXCP. HA)
ENGINE STALL
HESITATION/SURGING/FLAT SPOT
SPARK KNOCK/DETONATION
LACK OF POWER/POOR ACCELERATION
HIGH IDLE/LOW IDLE
ROUGH IDLE/HUNTING
IDLING VIBRATION
SLOW/NO RETURN TO IDLE
OVERHEATS/WATER TEMPERATURE HIGH
EXCESSIVE FUEL CONSUMPTION
EXCESSIVE OIL CONSUMPTION
BATTERY DEAD (UNDER CHARGE)
Warranty symptom code AA AB AC AD AE AF AG AH AJ AK AL AM HA
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ENGINE CONTROL SYSTEMEC-531
< SYMPTOM DIAGNOSIS > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
1 - 6: The numbers refer to the order of inspection. Va l v e
mecha-
nism Timing chain
55555 55 5 EM-62
Camshaft
EM-47
Intake valve timing controlEM-62
Intake valve
3EM-78
Exhaust valve
Exhaust Exhaust manifold/Tube/Muf- fler/Gasket 55555 55 5 EM-33
, EX-6
Three way catalyst
Lubrica-
tion Oil pan/Oil strainer/Oil pump/
Oil filter/Oil gallery/Oil cooler 55555 55 5 EM-36
,
LU-9,
LU-11
, LU-7,
LU-17
Oil level (Low)/Filthy oil LU-9
Cooling Radiator/Hose/Radiator filler
cap
55555 55 45 CO-17
Thermostat 5
CO-22
Water pumpCO-20
Water galleryCO-7
Cooling fan
5CO-18
Coolant level (Low)/Contami-
nated coolant CO-11
NVIS (NISSAN Vehicle Immobilizer Sys-
tem — NATS) 11
SEC-63
SYMPTOM
Reference page
HARD/NO START/RESTART (EXCP. HA)
ENGINE STALL
HESITATION/SURGING/FLAT SPOT
SPARK KNOCK/DETONATION
LACK OF POWER/POOR ACCELERATION
HIGH IDLE/LOW IDLE
ROUGH IDLE/HUNTING
IDLING VIBRATION
SLOW/NO RETURN TO IDLE
OVERHEATS/WATER TEMPERATURE HIGH
EXCESSIVE FUEL CONSUMPTION
EXCESSIVE OIL CONSUMPTION
BATTERY DEAD (UNDER CHARGE)
Warranty symptom code A AAB AC AD AE AF AG AH AJ AK AL AM HA
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PREPARATIONEC-547
< PREPARATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
Fuel filler cap adapter
i.e.: (MLR-8382) Checks fuel tank vacuum relief valve opening
pressure
Socket wrench Removes and installs engine coolant temperature sensor. Refer to CO-51, "Exploded View"
.
Oxygen sensor thread
cleaner
i.e.: (J-43897-18)
(J-43897-12) Reconditions the exhaust system threads before
installing a new oxygen sensor. Use with anti-
seize lubricant shown below.
a: 18 mm diameter with pitch 1.5 mm for Zirco-
nia Oxygen Sensor
b: 12 mm diameter with pitch 1.25 mm for Tita-
nia Oxygen Sensor
Anti-seize lubricant
i.e.: (Permatex
TM
133AR or equivalent
meeting MIL specifica-
tion MIL-A-907) Lubricates oxygen sensor thread cleaning tool
when reconditioning exhaust system threads.
Tool name
(TechMate No.) Description
S-NT815
S-NT705
AEM488
S-NT779
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-550
< SYSTEM DESCRIPTION >[VQ35DE]
COMPONENT PARTS
EXHAUST
BODY
8.Ignition coil (with power transistor)
(bank 2) EC-560, "Ignition Coil (With Power Transistor)"
9.Camshaft position sensor (PHASE)
(bank 2) EC-554, "Camshaft Posi
tion Sensor (PHASE)"
10. Engine coolant temperature sensor EC-556, "Engine Coolant Temperature Sensor"
11. Fuel injector (bank 1)EC-558, "Fuel Injector"
12. Knock sensor (bank 1)EC-560, "Knock Sensor"
13. Knock sensor (bank 2)EC-560, "Knock Sensor"
14. Fuel injector (bank 2)EC-558, "Fuel Injector"
15. Engine oil temperature sensorEC-557, "Engine Oil Temperature Sensor"
No. Component Function
JPBIA4687ZZ
No. Component Function
1. Air fuel ratio (A/F ) sensor 1 (bank 2) EC-552, "Air Fuel Ratio (A/F) Sensor 1"
2. Heated oxygen sensor 2 (bank 2) EC-559, "Heated Oxygen Sensor 2"
3. Heated oxygen sensor 2 (bank 1)EC-559, "Heated Oxygen Sensor 2"
4. Air fuel ratio (A/F) sensor 1 (bank 1) EC-552, "Air Fuel Ratio (A/F) Sensor 1"
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-554
< SYSTEM DESCRIPTION >[VQ35DE]
COMPONENT PARTS
Camshaft Position Sensor (PHASE)
INFOID:0000000009462485
The camshaft position sensor (P HASE) senses the retraction of
intake camshaft to identify a particular cylinder. The camshaft posi-
tion sensor (PHASE) sens es the piston position.
When the crankshaft position sensor (POS) system becomes inoper-
ative, the camshaft position sensor (PHASE) provides various con-
trols of engine parts instead, utilizing timing of cylinder identification
signals.
The sensor consists of a permanent magnet and Hall IC.
When engine is running, the high and low parts of the teeth cause
the gap with the sensor to change.
The changing gap causes the magnetic field near the sensor to
change.
Due to the changing magnetic field, the voltage from the sensor changes.
ECM receives the signals as shown in the figure.
Cooling FanINFOID:0000000009462486
DESCRIPTION
The ECM controls the cooling fan corresponding to the vehicle speed, engine coolant temperature, refrigerant
pressure, and air conditioner ON signal. The control system has 4-step control [HIGH/MIDDLE/LOW/OFF].
Refer to EC-575, "COOLING FAN CONTRO L : System Description"
for cooling fan operation.
COOLING FAN MOTOR RELAY
Power supply for the cooling fan motor is provided via cooling fan motor relay.
Crankshaft Position Sensor (POS)INFOID:0000000009462487
The crankshaft position sensor (POS) is located on the oil pan facing
the gear teeth (cogs) of the signal pl ate. It detects the fluctuation of
the engine revolution.
The sensor consists of a permanent magnet and Hall IC.
When the engine is running, the high and low parts of the teeth
cause the gap with the sensor to change.
The changing gap causes the magnetic field near the sensor to
change.
Due to the changing magnetic field, the voltage from the sensor
changes.
The ECM receives the voltage signal and detects the fluctuation of
the engine revolution.
JMBIA0064ZZ
JMBIA0001GB
JMBIA0062ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-556
< SYSTEM DESCRIPTION >[VQ35DE]
COMPONENT PARTS
The throttle position sensor has
two sensors. These sensors are a
kind of potentiometers which transform the throttle valve position into
output voltage, and emit the voltage signal to the ECM. In addition,
these sensors detect the opening and closing speed of the throttle
valve and feed the voltage signals to the ECM. The ECM judges the
current opening angle of the throttle valve from these signals and the
ECM controls the throttle control motor to make the throttle valve
opening angle properly in response to driving condition.
Electronic Controlled Engine MountINFOID:0000000009462490
In the idle range, ECM turns OFF the electronically- controlled engine mount control solenoid valve and applies
manifold pressure to the electronically-controlled engi ne mount. This decreases damping force of the electron-
ically-controlled engine mount and absorbs vibrations trav eling from the engine to the body for improving the
quietness.
In the driving range, ECM turns ON the electronicall y-controlled engine mount control solenoid valve and cuts
manifold pressure applied on the electronically-controlled engine mount. This increases damping force of the
electronically-controlled engine mount and r educes vibrations generated during driving.
Engine Coolant Temperature SensorINFOID:0000000009462491
The engine coolant temperature sensor is used to detect the engine
coolant temperature. The sensor modifies a voltage signal from the
ECM. The modified signal returns to the ECM as the engine coolant
temperature input. The sensor uses a thermistor which is sensitive to
the change in temperature. The elec trical resistance of the ther-
mistor decreases as temperature increases.

*: These data are reference values and are measured between ECM terminals.
PBIB0145E
SEF594K
Engine coolant temperature [° C ( °F)] Vol tag e* (V)
Resistance (k
Ω)
–10 (14) 4.4 7.0 - 11.4 20 (68) 3.5 2.37 - 2.63
50 (122) 2.2 0.68 - 1.00
90 (194) 0.9 0.236 - 0.260
SEF012P
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

COMPONENT PARTSEC-559
< SYSTEM DESCRIPTION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
FUEL LEVEL SENSOR
The fuel level sensor is mounted in the fuel level sensor unit.
The sensor detects a fuel level in the fuel tank and tr ansmits a signal to the combination meter. The combina-
tion meter sends the fuel level sensor signal to the ECM via the CAN communication line.
It consists of two parts, one is mechanical float and the ot her is variable resistor. Fuel level sensor output volt-
age changes depending on the movement of the fuel mechanical float.
FUEL TANK TEMPERATURE SENSOR
The fuel tank temperature sensor is used to detect the fuel tempera-
ture inside the fuel tank. The sensor modifies a voltage signal from
the ECM. The modified signal returns to the ECM as the fuel temper-
ature input. The sensor uses a ther mistor which is sensitive to the
change in temperature. The electrical resistance of the thermistor
decreases as temperature increases.

*: These data are reference values and are measured between ECM terminals 95 (Fuel tank temperature sensor) and ground.
Heated Oxygen Sensor 2INFOID:0000000009462500
DESCRIPTION
The heated oxygen sensor 2, after three way catalyst (manifold),
monitors the oxygen level in the exhaust gas.
Even if switching characteristics of the air fuel ratio (A/F) sensor 1
are shifted, the air fuel ratio is c ontrolled to stoichiometric, by the sig-
nal from the heated oxygen sensor 2.
This sensor is made of ceramic zirconia. The zirconia generates volt-
age from approximately 1 V in richer conditions to 0 V in leaner con-
ditions.
Under normal conditions the heated oxygen sensor 2 is not used for
engine control operation.
HEATED OXYGEN SENSOR 2 HEATER
Heated oxygen sensor 2 heater is integrated in the sensor.
The ECM performs ON/OFF control of the heated oxygen sensor 2 heater corresponding to the engine speed,
amount of intake air and engine coolant temperature.
Condition Fuel pump operation
Ignition switch is turned to ON. Operates for 1 second.
Engine running and cranking Operates.
When engine is stopped Stops in 1.5 seconds.
Except as shown above Sto ps .
Fluid temperature
[° C ( °F)] Voltage*
(V) Resistance
(kΩ)
20 (68) 3.5 2.3 - 2.7
50 (122) 2.2 0.79 - 0.90
SEF012P
SEF327R
Engine speed Heated oxygen sensor 2 heater
Above 3,600 rpm OFF
Below 3,600 rpm after the following conditions are met.
• Engine: After warming up
• Keeping the engine speed between 3,500 and 4,000 rpm for 1
minute and at idle for 1 minute under no load ON
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

SYSTEMEC-567
< SYSTEM DESCRIPTION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
P0117
P0118 Engine coolant tempera-
ture sensor circuit Engine coolant temperature will be determined by ECM based on the following condition.
CONSULT displays the engine coolant temperature decided by ECM.
Condition Engine coolant temperature decided
(CONSULT display)
Just as ignition switch is turned ON
or START 40
°C (104 °F)
Approx 4 minutes or more after en-
gine starting 80
°C (176 °F)
Except as shown above 40 - 80
°C (104 - 176 °F)
(Depends on the time)
When the fail-safe system for engine coolant temperature sensor is activated, the cooling
fan operates while engine is running.
P0122
P0123
P0222
P0223
P2135 Throttle position sensor The ECM controls the electric throttle control actuator in regulating the throttle opening in
order for the idle position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal
condition.
Therefore, the acceleration will be poor.
P0196
P0197
P0198 Engine oil temperature
sensor Intake valve timing control does not function.
P0500 Vehicle speed sensor The cooling fan operates (Highest) while engine is running.
P0524 Engine oil pressure • ECM illuminates oil pressure warning lamp on the combination meter.
• Engine speed will not rise more than 4,000 rpm due to the fuel cut.
• Fail-safe is canceled when ignition switch OFF → ON.
P0605 ECM (When ECM calculation function is malfunctioning:) ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
ECM deactivates ASCD operation.
P0643 Sensor power supply ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.
P1805 Brake switch ECM controls the electric throttle control actuator by regulating the throttle opening to a small range.
Therefore, acceleration will be poor.
Vehicle condition Driving condition
When engine is idling Normal
When accelerating Poor acceleration
P2100
P2103 Throttle control motor relay ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P2101 Electric th rottle control
function ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P2118 Throttle control motor ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.
DTC No. Detected items Engine operating condition in fail-safe mode
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

SYSTEMEC-569
< SYSTEM DESCRIPTION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
*1: ECM determines the start signal status
by the signals of engine speed and battery voltage.
*2: This sensor is not used to contro l the engine system under normal conditions.
*3: Automatic air conditioning system
*4: Manual air conditioning system
SYSTEM DESCRIPTION
The amount of fuel injected from the fuel injector is determined by the ECM. The ECM controls the length of
time the valve remains open (injection pulse duration). T he amount of fuel injected is a program value in the
ECM memory. The program value is preset by engi ne operating conditions. These conditions are determined
by input signals (for engine speed and intake air) from t he crankshaft position sensor (POS), camshaft position
sensor (PHASE) and the mass air flow sensor.
VARIOUS FUEL INJECTION INCREASE/DECREASE COMPENSATION
In addition, the amount of fuel injected is compens ated to improve engine performance under various operat-
ing conditions as listed below.

• During warm-up
• When starting the engine
• During acceleration
• Hot-engine operation
• When selector lever position is changed from N to D
• High-load, high-speed operation

• During deceleration
• During high engine speed operation
Sensor Input signal to ECM ECM function Actuator
Crankshaft position sensor (POS) Engine speed
*1
Fuel injection
& mixture ratio
control Fuel injector
Camshaft position sensor (PHASE) Piston position
Mass air flow sensor Amount of intake air
Intake air temperature sensor Intake air temperature
Engine coolant temperature sensor Engine coolant temperature
Air fuel ratio (A/F) sensor 1 Density of oxygen in exhaust gas
Throttle position sensor Throttle position
Accelerator pedal position sensor Accelerator pedal position
Transmission range switch Gear position
Battery Battery voltage
*1
Knock sensor Engine knocking condition
Heated oxygen sensor 2
*2Density of oxygen in exhaust gas
ABS actuator and electric unit (control unit) • VDC operation signal
• TCS operation signal
CAN communi-
cation
Power steering control module EPS operation signal
Combination meter Vehicle speed signal
A/C auto amp.
*3• A/C ON signal
• Blower fan ON signal
BCM
*4
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM