lock NISSAN TEANA 2014 Service Manual

POWER DOOR LOCK SYSTEMDLK-53
< WIRING DIAGRAM >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
ABKWA2181GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-54
< WIRING DIAGRAM >
POWER DOOR LOCK SYSTEM
ABKIA3596GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

POWER DOOR LOCK SYSTEMDLK-55
< WIRING DIAGRAM >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
ABKIA4842GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-56
< WIRING DIAGRAM >
POWER DOOR LOCK SYSTEM
ABKIA4830GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

POWER DOOR LOCK SYSTEMDLK-57
< WIRING DIAGRAM >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
ABKIA3599GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-58
< WIRING DIAGRAM >
POWER DOOR LOCK SYSTEM
ABKIA3600GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

POWER DOOR LOCK SYSTEMDLK-59
< WIRING DIAGRAM >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
ABKIA4812GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-60
< WIRING DIAGRAM >
POWER DOOR LOCK SYSTEM
ABKIA4811GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-92
< DTC/CIRCUIT DIAGNOSIS >
B26FD SHIFT LOCK SOLENOID
B26FD SHIFT LOCK SOLENOID
DTC LogicINFOID:0000000009461818
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES >> Refer to DLK-92, "Diagnosis Procedure".
NO >> Shift lock solenoid is OK.
Diagnosis ProcedureINFOID:0000000009461819
Regarding Wiring Diagram information, refer to DLK-61, "Wiring Diagram".
1. CHECK POWER SOURCE (STOP LAMP SWITCH)
1. Turn ignition switch OFF.
2. Disconnect stop lamp switch connector.
3. Check voltage between stop lamp switch connector E38 terminal 1 and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Check the following: • Harness for short or open between fuse block (J/B) and stop lamp switch
• 10A fuse (No. 10, located in fuse block [J/B])
2.CHECK STOP LAMP SWITCH
Check stop lamp switch. Refer to BRC-78, "Diagnosis Procedure"
.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace stop lamp switch. Refer to BR-18, "Exploded View"
.
3.CHECK GROUND CIRCUIT (STOP LAMP RELAY)
1. Remove the stop lamp relay.
2. Check continuity between stop lamp relay connector E57 terminal 1 and ground.
Is the inspection result normal?
DTC CONSULT display
description DTC detecting condition Possible cause
B26FD SHIFT LOCK SOLE-
NOID BCM shift lock solenoid output control is OFF but
shift lock solenoid output feedback is ON. • Shift lock solenoid
• Harness or connector
• Shift lock solenoid circuit is open or shorted
Stop lamp switch
GroundVoltage
Connector Terminal
E38 1 Battery voltage
Sto p l am p rela y GroundContinuity
Connector Terminal (+)
E57 1 Yes
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

B26FD SHIFT LOCK SOLENOIDDLK-93
< DTC/CIRCUIT DIAGNOSIS >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
YES >> GO TO 4.
NO >> Repair or replace damaged parts.
4.CHECK HARNESS BETWEEN STOP LAMP RELAY AND BCM
1. Check continuity between stop lamp relay connecto r E57 terminal 3 and BCM connector M17 terminal 27.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace damaged parts.
5.CHECK HARNESS BETWEEN STOP LAMP SWITCH AND STOP LAMP RELAY
1. Check continuity between stop lamp relay connector E57 terminal 2 and stop lamp switch connector E38
terminal 2.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace damaged parts.
6.CHECK GROUND CIRCUIT (STOP LAMP RELAY)
1. Remove the stop lamp relay.
2. Check continuity between stop lamp relay connector E57 terminal 1 and ground.
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace damaged parts.
7.CHECK POWER SOURCE (STOP LAMP RELAY)
1. Check voltage between stop lamp relay connector E57 terminal 5 and ground.
Is the inspection result normal?
YES >> GO TO 8.
NO >> Repair or replace damaged parts.
8.CHECK HARNESS BETWEEN BCM AND CVT SHIFT SELECTOR FOR OPEN
1. Disconnect CVT shift selector connector.
2. Check continuity between BCM connector M20 termi nal 108 and CVT shift selector connector M23 termi-
nal 3.
BCM Stop lamp relay Continuity
Connector Terminal Connector Terminal
M17 27 E57 3 Yes
Stop lamp switch Stop lamp relay Continuity
Connector Terminal Connector Terminal
E38 2 E57 2 Yes
St op la mp rel ay GroundContinuity
Connector Terminal (+)
E57 1 Yes
St op la mp rel ay GroundContinuity
Connector Terminal (+)
E57 5 Battery voltage
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM