service NISSAN TEANA 2014 Manual PDF

DAS-3
C
D E
F
G H
I
J
K L
M B
DAS
N
P
A
BASIC INSPECTION .......
..........................100
DIAGNOSIS AND REPAIR WORK FLOW .... ..100
Work Flow ........................................................... ..100
Diagnostic Work Sheet ..........................................101
PRE-INSPECTION FOR DIAGNOSIS ..............103
Inspection Procedure .......................................... ..103
ACTION TEST ..................................................104
Description .......................................................... ..104
Inspection Procedure ............................................104
ADDITIONAL SERVICE WHEN REPLACING
REAR VIEW CAMERA ................................... ..
106
Description .......................................................... ..106
Work Procedure ....................................................106
REAR VIEW CAMERA CALIBRATION ...........107
Description .......................................................... ..107
Work Procedure (Preparation) ..............................107
Work Procedure (Target Setting) ..........................108
Work Procedure (Rear View Camera Calibration) ..109
DTC/CIRCUIT DIAGNOSIS .......................111
C1A03 VEHICLE SPEED SENSOR ............... ..111
DTC Logic ........................................................... ..111
Diagnosis Procedure .............................................111
C1A04 ABS/TCS/VDC SYSTEM ......................112
DTC Logic ........................................................... ..112
Diagnosis Procedure .............................................112
C1A39 STEERING ANGLE SENSOR ..............113
DTC Logic ........................................................... ..113
Diagnosis Procedure .............................................113
U0122 VDC P-RUN DIAG ................................114
DTC Logic ........................................................... ..114
Diagnosis Procedure .............................................114
U0416 VDC CHECKSUM DIAG .......................115
DTC Logic ........................................................... ..115
Diagnosis Procedure .............................................115
U0428 STEERING ANGLE SENSOR ..............116
DTC Logic ........................................................... ..116
Diagnosis Procedure .............................................116
U1000 CAN COMM CIRCUIT ...........................117
Description .......................................................... ..117
DTC Logic .............................................................117
Diagnosis Procedure .............................................117
U1010 CONTROL UNIT (CAN) ........................118
Description .......................................................... ..118
DTC Logic .............................................................118
Diagnosis Procedure .............................................118
U111A REAR CAMERA IMAGE SIGNAL CIR-
CUIT ................................................................
119
DTC Logic ............................................................ ..119
Diagnosis Procedure .............................................119
U1232 STEERING ANGLE SENSOR .............121
DTC Logic ..............................................................121
Diagnosis Procedure .............................................121
U1305 CAMERA IMAGE CALIB .....................122
DTC Logic ..............................................................122
Diagnosis Procedure .............................................122
U1308 CAMERA CONFIG ..............................123
DTC Logic ..............................................................123
Diagnosis Procedure .............................................123
U1309 PUMP UNIT CURRENT .......................124
DTC Logic ..............................................................124
Diagnosis Procedure .............................................124
U130B REAR CAMERA COMM ERROR .......127
DTC Logic ..............................................................127
Diagnosis Procedure .............................................127
U1310 PUMP UNIT CIRCUIT ..........................128
DTC Logic ..............................................................128
Diagnosis Procedure .............................................128
POWER SUPPLY AND GROUND CIRCUIT ..131
Diagnosis Procedure .............................................131
WARNING SYSTEMS SWITCH CIRCUIT ......132
Component Function Check ..................................132
Diagnosis Procedure .............................................132
Component Inspection ...........................................133
WARNING SYSTEMS ON INDICATOR CIR-
CUIT ................................................................
134
Component Function Check ................................ ..134
Diagnosis Procedure .............................................134
Component Inspection ...........................................135
WARNING BUZZER CIRCUIT ........................136
Component Function Check ..................................136
Diagnosis Procedure .............................................136
SYMPTOM DIAGNOSIS ............................137
LDW SYSTEM SYMPTOMS ...........................137
Symptom Table ................................................... ..137
LANE DEPARTURE WARNING LAMP DOES
NOT TURN ON ................................................
138
Description ........................................................... ..138
Diagnosis Procedure .............................................138
THE SYSTEM OPERATES EVEN WHEN US-
ING TURN SIGNAL .........................................
139
Description ........................................................... ..139
Diagnosis Procedure .............................................139
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-4
LDW SYSTEM SETTINGS CANNOT BE
TURNED ON/OFF IN VEHICLE INFORMA-
TION DISPLAY ............................................... .
140
Description ........................................................... ..140
Diagnosis Procedure .............................................140
NORMAL OPERATING CONDITION ..............141
Description ........................................................... ..141
REMOVAL AND INSTALLATION ..............142
WARNING SYSTEMS SWITCH ..................... .142
Removal and Installation ..................................... ..142
REAR VIEW CAMERA ....................................143
Exploded View ..................................................... ..143
Removal and Installation .......................................143
REAR VIEW CAMERA WASHER CONTROL
UNIT ................................................................ .
144
Exploded View ..................................................... ..144
Removal and Installation .......................................144
REAR VIEW CAMERA AIR PUMP MOTOR ...145
Exploded View ..................................................... ..145
Removal and Installation .......................................145
BSW
PRECAUTION .............. ..............................
146
PRECAUTIONS .............................................. .146
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .............................................................. ..
146
Precaution for Work ...............................................146
Precautions For Harness Repair ...........................146
Precaution for BSW System Service .....................147
PREPARATION ..........................................148
PREPARATION .............................................. .148
Special Service Tool ............................................ ..148
SYSTEM DESCRIPTION ...........................149
COMPONENT PARTS .................................... .149
Component Parts Location .................................. ..149
Component Description .........................................150
SYSTEM .......................................................... .152
System Description .............................................. ..152
Fail-safe (ITS Control Unit) ....................................154
OPERATION ................................................... .155
Switch Name and Function .................................. ..155
System Display and Warning ................................155
HANDLING PRECAUTION ..............................157
Precautions for Blind Spot Warning ..................... ..157
DIAGNOSIS SYSTEM (ITS CONTROL UNIT) .158
CONSULT Function (AVM) ................................. ..158
ECU DIAGNOSIS INFORMATION ............161
ITS CONTROL UNIT ........................................161
Reference Value .................................................. .161
Fail-safe ................................................................163
DTC Inspection Priority Chart .............................. .163
DTC Index ............................................................ .164
WIRING DIAGRAM ...................................166
DRIVER ASSISTANCE SYSTEMS ................ ..166
Wiring Diagram .................................................... .166
BASIC INSPECTION .................................175
DIAGNOSIS AND REPAIR WORK FLOW ..... ..175
Work Flow ............................................................ .175
Diagnostic Work Sheet .........................................176
PRE-INSPECTION FOR DIAGNOSIS ..............178
Inspection Procedure ........................................... .178
ACTION TEST ..................................................179
Description ........................................................... .179
Inspection Procedure ............................................179
ADDITIONAL SERVICE WHEN REPLACING
REAR VIEW CAMERA ................................... ..
181
Description ........................................................... .181
Work Procedure ....................................................181
REAR VIEW CAMERA CALIBRATION ...........182
Description ........................................................... .182
Work Procedure (Preparation) ..............................182
Work Procedure (Target Se tting) ..........................183
Work Procedure (Rear View Camera Calibration) .184
DTC/CIRCUIT DIAGNOSIS .......................186
C1A03 VEHICLE SPEED SENSOR .................186
DTC Logic ............................................................ .186
Diagnosis Procedure .............................................186
C1A04 ABS/TCS/VDC SYSTEM ......................187
DTC Logic ............................................................ .187
Diagnosis Procedure .............................................187
C1A39 STEERING ANGLE SENSOR ..............188
DTC Logic ............................................................ .188
Diagnosis Procedure .............................................188
U0122 VDC P-RUN DIAG .................................189
DTC Logic ............................................................ .189
Diagnosis Procedure .............................................189
U0416 VDC CHECKSUM DIAG .......................190
DTC Logic ............................................................ .190
Diagnosis Procedure .............................................190
U0428 STEERING ANGLE SENSOR ..............191
DTC Logic ............................................................ .191
Diagnosis Procedure .............................................191
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-5
C
D E
F
G H
I
J
K L
M B
DAS
N
P
A
U1000 CAN COMM CI
RCUIT ...........................192
Description .......................................................... ..192
DTC Logic .............................................................192
Diagnosis Procedure .............................................192
U1010 CONTROL UNIT (CAN) ........................193
Description .......................................................... ..193
DTC Logic .............................................................193
Diagnosis Procedure .............................................193
U111A REAR CAMERA IMAGE SIGNAL CIR-
CUIT ................................................................ ..
194
DTC Logic ........................................................... ..194
Diagnosis Procedure .............................................194
U1232 STEERING ANGLE SENSOR ..............196
DTC Logic ........................................................... ..196
Diagnosis Procedure .............................................196
U1305 CAMERA IMAGE CALIB ......................197
DTC Logic ........................................................... ..197
Diagnosis Procedure .............................................197
U1308 CAMERA CONFIG ................................198
DTC Logic ........................................................... ..198
Diagnosis Procedure .............................................198
U1309 PUMP UNIT CURRENT ........................199
DTC Logic ........................................................... ..199
Diagnosis Procedure .............................................199
U130B REAR CAMERA COMM ERROR ........202
DTC Logic ........................................................... ..202
Diagnosis Procedure .............................................202
U1310 PUMP UNIT CIRCUIT ...........................203
DTC Logic ........................................................... ..203
Diagnosis Procedure .............................................203
POWER SUPPLY AND GROUND CIRCUIT ....206
Diagnosis Procedure ........................................... ..206
WARNING SYSTEMS SWITCH CIRCUIT .......207
Component Function Check ................................ ..207
Diagnosis Procedure .............................................207
Component Inspection ..........................................208
WARNING SYSTEMS ON INDICATOR CIR-
CUIT ................................................................ ..
209
Component Function Check ................................ ..209
Diagnosis Procedure .............................................209
Component Inspection ..........................................210
WARNING BUZZER CIRCUIT .........................211
Component Function Check ................................ ..211
Diagnosis Procedure .............................................211
SYMPTOM DIAGNOSIS ............................212
BSW SYSTEM SYMPTOMS .......................... ..212
Symptom Table ................................................... ..212
SWITCH DOES NOT TURN ON / SWITCH
DOES NOT TURN OFF ...................................
213
Description ........................................................... ..213
Diagnosis Procedure .............................................213
BSW SYSTEM SETTINGS CANNOT BE
TURNED ON/OFF IN VEHICLE INFORMA-
TION DISPLAY ................................................
215
Description ........................................................... ..215
Diagnosis Procedure .............................................215
NORMAL OPERATING CONDITION .............216
Description .............................................................216
REMOVAL AND INSTALLATION .............217
WARNING SYSTEMS SWITCH ......................217
Removal and Installation ..................................... ..217
BSW INDICATOR ...........................................218
Exploded View .......................................................218
Removal and Installation .......................................218
REAR VIEW CAMERA ....................................219
Exploded View .......................................................219
Removal and Installation .......................................219
REAR VIEW CAMERA WASHER CONTROL
UNIT ................................................................
220
Exploded View ..................................................... ..220
Removal and Installation .......................................220
REAR VIEW CAMERA AIR PUMP MOTOR ...221
Exploded View .......................................................221
Removal and Installation .......................................221
MOD
PRECAUTION ...... ......................................
222
PRECAUTIONS ...............................................222
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ..
222
Precaution for Work ...............................................222
Precautions For Harness Repair ...........................222
PREPARATION .........................................224
PREPARATION ...............................................224
Special Service Tool ............................................ ..224
SYSTEM DESCRIPTION ...........................225
COMPONENT PARTS ....................................225
Component Parts Location .................................. ..225
Component Description .........................................226
SYSTEM ..........................................................228
System Description .............................................. ..228
OPERATION ...................................................231
System Display and Warning ................................231
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-6
HANDLING PRECAUTION ..............................232
Precautions for Moving Objects Detection .......... ..232
DIAGNOSIS SYSTEM (ITS CONTROL UNIT) .233
CONSULT Function (AVM) ................................. ..233
ECU DIAGNOSIS INFORMATION .............236
ITS CONTROL UNIT ....................................... .236
Reference Value .................................................. ..236
Fail-safe .................................................................238
DTC Inspection Priority Chart ................................238
DTC Index .............................................................239
WIRING DIAGRAM ....................................241
DRIVER ASSISTANCE SYSTEMS ................ .241
Wiring Diagram .................................................... ..241
BASIC INSPECTION ..................................250
DIAGNOSIS AND REPAIR WORK FLOW ..... .250
Work Flow ............................................................ ..250
Diagnostic Work Sheet ..........................................251
PRE-INSPECTION FOR DIAGNOSIS .............253
Inspection Procedure ........................................... ..253
ACTION TEST .................................................254
Description ........................................................... ..254
Inspection Procedure .............................................254
ADDITIONAL SERVICE WHEN REPLACING
REAR VIEW CAMERA ................................... .
255
Description ........................................................... ..255
Work Procedure .....................................................255
REAR VIEW CAMERA CALIBRATION ..........256
Description ........................................................... ..256
Work Procedure (Preparation) ...............................256
Work Procedure (Target Setting) ...........................257
Work Procedure (Rear View Camera Calibration) ..258
DTC/CIRCUIT DIAGNOSIS ...................... ..260
C1A03 VEHICLE SPEED SENSOR ............... .260
DTC Logic ............................................................ ..260
Diagnosis Procedure .............................................260
C1A04 ABS/TCS/VDC SYSTEM .....................261
DTC Logic ............................................................ ..261
Diagnosis Procedure .............................................261
C1A39 STEERING ANGLE SENSOR .............262
DTC Logic ............................................................ ..262
Diagnosis Procedure .............................................262
U0122 VDC P-RUN DIAG ................................263
DTC Logic ............................................................ ..263
Diagnosis Procedure .............................................263
U0416 VDC CHECKSUM DIAG ......................264
DTC Logic ............................................................ .264
Diagnosis Procedure .............................................264
U0428 STEERING ANGLE SENSOR ..............265
DTC Logic ............................................................ .265
Diagnosis Procedure .............................................265
U1000 CAN COMM CIRCUIT ...........................266
Description ........................................................... .266
DTC Logic .............................................................266
Diagnosis Procedure .............................................266
U1010 CONTROL UNIT (CAN) ........................267
Description ........................................................... .267
DTC Logic .............................................................267
Diagnosis Procedure .............................................267
U111A REAR CAMERA IMAGE SIGNAL CIR-
CUIT ................................................................ ..
268
DTC Logic ............................................................ .268
Diagnosis Procedure .............................................268
U1232 STEERING ANGLE SENSOR ..............270
DTC Logic ............................................................ .270
Diagnosis Procedure .............................................270
U1305 CAMERA IMAGE CALIB ......................271
DTC Logic ............................................................ .271
Diagnosis Procedure .............................................271
U1308 CAMERA CONFIG ................................272
DTC Logic ............................................................ .272
Diagnosis Procedure .............................................272
U1309 PUMP UNIT CURRENT ........................273
DTC Logic ............................................................ .273
Diagnosis Procedure .............................................273
U130B REAR CAMERA COMM ERROR .........276
DTC Logic ............................................................ .276
Diagnosis Procedure .............................................276
U1310 PUMP UNIT CIRCUIT ...........................277
DTC Logic ............................................................ .277
Diagnosis Procedure .............................................277
POWER SUPPLY AND GROUND CIRCUIT ....280
Diagnosis Procedure ............................................ .280
WARNING SYSTEMS SWITCH CIRCUIT ........281
Component Function Check ................................ .281
Diagnosis Procedure .............................................281
Component Inspection ..........................................282
WARNING SYSTEMS ON INDICATOR CIR-
CUIT ................................................................ ..
283
Component Function Check ................................ .283
Diagnosis Procedure .............................................283
Component Inspection ..........................................284
WARNING BUZZER CIRCUIT .........................285
Component Function Check ................................ .285
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-8
< PRECAUTION >[ITS CONTROL UNIT]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint Syst
em (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009951635
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISS AN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harn esses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precautions For Harness RepairINFOID:0000000009464647
ITS communication uses a twisted pair line. Be careful when repairing it.
• Solder the repaired area and wrap tape around the soldered area.
NOTE:
A fray of twisted lines must be within 110 mm (4.33 in).
• Bypass connection is never allowed at the repaired area. NOTE:
Bypass connection may cause ITS communication error. The
spliced wire becomes separated and the characteristics of twisted
line are lost.
SKIB8766E
SKIB8767E
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
ACTION TESTDAS-35
< BASIC INSPECTION > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
ACTION TEST
DescriptionINFOID:0000000009464661
• Perform action test to verify the customer's concern.
• Perform action test and check the system operation after system diagnosis.
WARNING:
Be careful of traffic conditions and safety aro und the vehicle when performing road test.
CAUTION:
• Fully understand the following it ems well before the road test;
- Precautions: Refer to DAS-73, "Precaution for LDW System Service"
.
- System description for LDW: Refer to DAS-77, "System Description"
.
- System description for BSW: Refer to DAS-152, "System Description"
.
- System description for MOD: Refer to DAS-228, "System Description"
.
- Handling precaution: Refer to DAS-82, "Precautions for Lane Departure Warning"
.
Inspection ProcedureINFOID:0000000009464662
WARNING:
Be careful of traffic conditions and safety aro und the vehicle when performing road test.
CAUTION:
• Fully understand the following it ems well before the road test;
- Precautions: Refer to DAS-73, "Precaution for LDW System Service"
.
- System description for LDW: Refer to DAS-77, "System Description"
.
- System description for BSW: Refer to DAS-152, "System Description"
.
- System description for MOD: Refer to DAS-228, "System Description"
.
- Handling precaution: Refer to DAS-232, "Precautions for Moving Objects Detection"
.
1.CHECK LDW SYSTEM SETTING
1. Start the engine.
2. Check that the LDW system setting can be enabl ed/disabled on the vehicle information display.
3. Turn OFF the ignition switch and wait for 30 seconds or more.
4. Check that the previous setting is saved when the engine starts again.
>> GO TO 2.
2.ACTION TEST FOR LDW
1. Enable the setting of the LDW system on the vehicle information display.
2. Turn warning systems switch ON (w arning systems ON indicator is ON).
3. Check the LDW operation according to the following table.
Vehicle condition/ Driver's operation Action Warning sys-
tems ON indi-
cator Indication on the combination
meter Buzzer
Less than
Approx. 60 km/h (40 MPH) Close to lane marker No action ON —
ALOIA0191GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
ADDITIONAL SERVICE WHEN REPLACING REAR VIEW CAMERA
DAS-37
< BASIC INSPECTION > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
ADDITIONAL SERVICE WHEN RE PLACING REAR VIEW CAMERA
DescriptionINFOID:0000000009464663
Always perform the calibration after removing and installing or replacing the rear view camera.
CAUTION:
The system does not operate normally unless the rear view camera aiming adjustment is performed.
Always perform it.
Work ProcedureINFOID:0000000009464664
1.CAMERA AIMING ADJUSTMENT
Perform the camera aiming adjustment with CONSULT. Refer to DAS-38, "Description"
.
>> GO TO 2.
2.PERFORM SELF-DIAGNOSIS
Perform the self-diagnosis of rear view camera with CONSULT. Check if any DTC is detected.
Is any DTC detected?
YES >> Perform the trouble diagnosis for the detected DTC. Refer to DAS-20, "DTC Index".
NO >> GO TO 3.
3.LDW/BSW SYSTEM ACTION TEST
1. Perform the LDW/BSW syst em action test. Refer to DAS-35, "Description"
.
2. Check that the LDW/BSW system operates normally.
Is the inspection result normal?
YES >> Inspection End.
NO >> GO TO 4.
4.LDW/BSW ACTIVE TEST
1. Perform WASH ACTIVE on Active Test using CONSULT.
2. Perform air and washer tube connection check by AIR & WASH ACTIVE on Active Test:
(1) Washer fluid output count on the rear view camera is 3 to 5 times → OK
(2) Washer fluid output count on the rear view camera is 10 times → Check tube with yellow marking
(3) Washer fluid output count on the rear view camera is 1 time → Check tube with green marking
(4) No washer fluid output → Check tube with blue marking or check valve
>> Inspection End.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-40
< BASIC INSPECTION >[ITS CONTROL UNIT]
REAR VIEW CAMERA CALIBRATION
CAUTION:
Make sure that the black/white pattern of the center target is rotated as compared with the left and
right targets.
>> Go to DAS-40, "Work Procedure (Rear View Camera Calibration)"
.
Work Procedure (Rear View Camera Calibration)INFOID:0000000009464668
CAUTION:
Perform the calibration under the sp ecified vehicle condition (fuel full, no-load, specified tire pressure,
etc.). Refer to DAS-38, "Work Procedure (Preparation)"
.
1.CHECK REAR VIEW CAMERA HEIGHT
Measure the rear view camera height “H”.
>> GO TO 2.
2.REAR VIEW CAMERA CALIBRATION
1. Select “Work Support” on “AVM” with CONSULT.
2. Select “REAR CAMERA ITS”.
3. Select "OK". CAUTION:
• Perform the calibration after the ignition or engine has been kept on for at least 10 minutes to
stabilize camera.
• Operate CONSULT outside the vehicle, and close al l doors to retain appropriate vehicle altitude.
4. Input the rear view camera height "H", and then touch "APPLY".
5. Confirm that the same value is displayed on the center display.
6. Confirm the following items:
- The target should be accurately placed.
- The vehicle should be stopped.
- The vehicle should be under the specified vehicle condition.
7. Select “Start” to perform calibration.
8. Confirm the displayed item.
- “Completed”: Select “Completion”.
- Otherwise, perform the following services:
ALOIA0192GB
ALOIA0188ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
REAR VIEW CAMERA CALIBRATIONDAS-41
< BASIC INSPECTION > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
NOTE:
Replace camera unit if “00H Routine not activated” or “10H Writing error” are repeatedly indicated during the
above two services are performed.
9. Confirm that “Completed” is displayed and then select “End” to close the calibration procedure.
>> GO TO 3.
3.PERFORM SELF-DIAGNOSIS
Perform self-diagnosis of IT S control unit with CONSULT.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repa ir or replace the applicable item. Refer to DAS-
20, "DTC Index".
NO >> GO TO 4.
4.ACTION TEST
Test the system operation by action test. Refer to DAS-35, "Description"
.
>> Work End.
Displayed item Possible cause Service procedure
SUSPENSION —
Temporary malfunction in internal processing of the rear
view camera. Go back to Step 1
00H Routine not ac-
tivated Rear view camera unit malfunction.
Position the target appro-
priately again. Perform
the aiming again. Refer
to DAS-39, "Work Proce-
dure (Target Setting)".
10H Writing error • Temporary malfunction in internal processing of the
rear view camera.
• Rear view camera malfunction.
X AIMING NG Y
(X: 0 - 7, Y: 1 - 8) —• A target is not-yet-placed.
(The rear view camera cannot detect a target.)
• The position of the rear view camera is not correct.
• Inappropriate work environment.
• Inappropriate vehicle condition. Position the target appro-
priately again. Perform
the aiming again. Refer
to DAS-38, "Work Proce-
dure (Preparation)".
ABNORMALLY COM-
PLETED —
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-72
< PRECAUTION >[LDW]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint Syst
em (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009951640
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISS AN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harn esses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for WorkINFOID:0000000009464716
• When removing or disassembling each component, be careful not to damage or deform it. If a component may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a s hop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
Precautions For Harness RepairINFOID:0000000009464717
ITS communication uses a twisted pair line. Be careful when repairing it.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM