engine control NISSAN TIIDA 2007 Service Manual PDF

BRC-24
[ABS]
TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
ACTIVE TEST
CAUTION:

Do not perform active test while driving.

Make sure to completely bleed air from the brake system.

The ABS and brake warning lamps turn on during the active test.
Operation Procedure
1. Connect the CONSULT-II and CONSULT-II CONVERTER to the data link connector and start the engine.
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
2. Touch “START (NISSAN BASED VHCL)” on the display screen.
3. Touch “ABS”.
If “ABS” is not indicated, go to GI-40, "
CONSULT-II Data Link Connector (DLC) Circuit" .
4. Touch “ACTIVE TEST”.
5. The SELECT TEST ITEM screen is displayed.
6. Touch necessary test item.
7. With the “MAIN SIGNALS” display selected, touch “START”.
8. The Active Test screen will be displayed, so conduct the following test.
Solenoid Valve Operation Chart
NOTE:

If active test is performed with brake pedal depressed, pedal stroke may change. This is normal.

“TEST IS STOPPED” is displayed approximately 10 seconds after operation starts.

After “TEST IS STOPPED” is displayed, to perform test again, repeat Step 6.
ABS Motor
Touch “ON” and “OFF” on the screen. Check that ABS motor relay
operates as shown in table below.
NOTE:

If active test is performed with brake pedal depressed, pedal
stroke may change. This is normal.

“TEST IS STOPPED” is displayed approximately 10 seconds
after operation starts.
WFIA0045E
TEST ITEM CONDITION JUDGEMENT
FR RH SOL
FR LH SOL
RR RH SOL
RR LH SOLIgnition switch is turned ON.Brake fluid pressure control operation
IN SOL OUT SOL
UP (Increase): OFF OFF
KEEP (Hold): ON OFF
DOWN (Decrease): ON ON
Operation ON OFF
ABS actuator relay ON ON
ABS motor relay ON OFF
SFIA0593E

BRC-32
[ABS]
TROUBLE DIAGNOSES FOR SYMPTOMS
Revision: June 20062007 Versa
Long Stopping DistanceEFS006LY
1. CHECK BASE BRAKING SYSTEM PERFORMANCE
1. Disable ABS by disconnecting ABS actuator and electric unit (control unit) connector.
2. Drive vehicle and check brake operation.
NOTE:

Stopping distance may be longer than vehicles without ABS when road condition is slippery.

Driving the vehicle with the ABS actuator and electric unit (control unit) disconnected may induce DTCs
in electrical control units using CAN communication. After the inspection, clear all DTCs. Refer to LAN-
4, "SYSTEM DESCRIPTION" .
OK or NG
OK >> Go to BRC-30, "ABS Works Frequently" .
NG >> Perform Basic Inspection. Refer to BRC-17, "
Basic Inspection" .
ABS Does Not WorkEFS006LZ
CAUTION:
The ABS does not operate when the vehicle speed is 10 km/h (6 MPH) or less.
1. CHECK WARNING LAMP ACTIVATION
Turn ignition switch ON and check for warning lamp activation.

Warning lamp should activate for approximately 2 seconds after turning the ignition switch ON.
OK or NG
OK >> Carry out self-diagnosis. Refer to BRC-20, "SELF-DIAGNOSIS" .
NG >> Go to BRC-17, "
ABS WARNING LAMP INSPECTION" .
Pedal Vibration or ABS Operation NoiseEFS006M0
NOTE:
During ABS activation, pedal vibration may be felt and a noise may be heard. This is normal and does not indi-
cate a malfunction.
1. CHECK SYMPTOM
1. Apply brake.
2. Start engine.
Does the symptom occur only when engine is started?
YES >> Carry out self-diagnosis. Refer to BRC-20, "SELF-DIAGNOSIS" .
NO >> GO TO 2.
2. RECHECK SYMPTOM
Does the symptom occur only when electrical equipment switches (such as headlamps) are turned on?
YES >> Check for radio, antenna or related wiring that is routed too close to the ABS actuator and electric
unit (control unit) and reroute as necessary.
NO >> Go to BRC-30, "
ABS Works Frequently" .

BRC-36
[ABS]
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)
Revision: June 20062007 Versa
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)PFP:47660
Removal and InstallationEFS006L6
CAUTION:

Before servicing, disconnect battery cables.

To remove brake tube, use flare nut wrench to prevent flare nuts and brake tube from being dam-
aged. To install, use flare nut torque wrench, tighten flare nut to the specified torque. Refer to BR-
11, "Hydraulic Circuit" .

Do not apply excessive impact to ABS actuator and electric unit (control unit), such as dropping it.

Do not remove and install actuator by holding harness.

After work is completed, bleed air from brake tube and hose. Refer to BR-10, "Bleeding Brake Sys-
tem" .
REMOVAL
1. Disconnect ABS actuator and electric unit (control unit) connector.
2. Loosen brake tube flare nuts, then remove brake tubes from ABS actuator and electric unit (control unit).
3. Remove brake booster hose from engine. Refer to BR-22, "
Removal and Installation" .
4. Remove ABS actuator and electric unit (control unit) bracket mounting bolts.
5. Remove ABS actuator and electric unit (control unit) from vehicle.
1. To front right 2. To rear left 3. To rear right
4. To front left 5. From master cylinder primary side 6. From master cylinder secondary
side
7. ABS actuator and electric unit (con-
trol unit)8. Harness connector : Front
Refer to GI section for symbol marks in the figure.
WFIA0506E

CO-1
ENGINE COOLING SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION CO
A
CO
Revision: June 20062007 Versa PRECAUTIONS .......................................................... 2
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 2
Precautions Necessary for Steering Wheel Rotation
After Battery Disconnect .......................................... 2
OPERATION PROCEDURE ................................. 2
Precautions for Liquid Gasket .................................. 2
REMOVAL OF LIQUID GASKET SEALING .......... 2
LIQUID GASKET APPLICATION PROCEDURE ..... 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
OVERHEATING CAUSE ANALYSIS .......................... 5
Troubleshooting Chart .............................................. 5
COOLING SYSTEM .................................................... 7
Cooling Circuit .......................................................... 7
ENGINE COOLANT .................................................... 8
Inspection ................................................................. 8
LEVEL CHECK ..................................................... 8
CHECKING COOLING SYSTEM FOR LEAKS ..... 8
Changing Engine Coolant ........................................ 8
DRAINING ENGINE COOLANT ........................... 8
REFILLING ENGINE COOLANT .......................... 8
FLUSHING COOLING SYSTEM ........................... 9
RADIATOR .................................................................11
Components ............................................................11
Removal and Installation ........................................ 12
REMOVAL ........................................................... 12
INSTALLATION ................................................... 12
INSPECTION AFTER INSTALLATION ............... 12
Checking Radiator Cap .......................................... 13
Checking Radiator .................................................. 13
COOLING FAN ......................................................... 15
Components (Models With A/C) ............................. 15Components (Models Without A/C) ........................ 15
Removal and Installation ........................................ 16
REMOVAL ........................................................... 16
INSTALLATION ................................................... 16
DISASSEMBLY AND ASSEMBLY .......................... 16
DISASSEMBLY ................................................... 16
INSPECTION AFTER DISASSEMBLY ............... 16
ASSEMBLY ......................................................... 16
WATER PUMP .......................................................... 17
Components ........................................................... 17
Removal and Installation ........................................ 17
REMOVAL ........................................................... 17
INSPECTION AFTER REMOVAL ....................... 17
INSTALLATION ................................................... 17
INSPECTION AFTER INSTALLATION ................ 17
THERMOSTAT .......................................................... 18
Components ........................................................... 18
Removal and Installation ........................................ 18
REMOVAL ........................................................... 18
INSPECTION AFTER REMOVAL ....................... 18
INSTALLATION ................................................... 19
INSPECTION AFTER INSTALLATION ................ 19
WATER OUTLET AND WATER CONTROL VALVE ... 20
Components ........................................................... 20
Removal and Installation ........................................ 20
REMOVAL ........................................................... 20
INSPECTION AFTER REMOVAL ....................... 21
INSTALLATION ................................................... 21
INSPECTION AFTER INSTALLATION ................ 22
SERVICE DATA AND SPECIFICATIONS (SDS) ...... 23
Standard and Limit .................................................. 23
CAPACITY ........................................................... 23
THERMOSTAT .................................................... 23
WATER CONTROL VALVE ................................. 23
RADIATOR .......................................................... 23

ENGINE COOLANT
CO-9
C
D
E
F
G
H
I
J
K
L
MA
CO
Revision: June 20062007 Versa

If water drain plug on cylinder block is removed, close and tighten it. Refer to EM-77, "CYLIN-
DER BLOCK" .
CAUTION:
Be sure to clean radiator drain plug and install with new O-ring. Refer to CO-11, "
Components" .
3. Make sure that each hose clamp has been firmly tightened.
4. Remove air duct assembly. Refer to EM-16, "
AIR CLEANER AND AIR DUCT" .
5. Disconnect heater hose (1) at position ( ) as shown.

Front

Reposition heater hose as high as possible.
6. Fill radiator and reservoir tank to specified level.

Pour engine coolant through engine coolant filler neck
slowly of less than 2 (2 1/8 US qt, 1-3/4 lmp qt) a minute
to allow air in system to escape.

Use NISSAN Genuine Engine Coolant or equivalent
mixed with water (distilled or demineralized). Fill cooling
system to specification. Refer to MA-11, "
RECOM-
MENDED FLUIDS AND LUBRICANTS".

When engine coolant overflows disconnected heater hose,
connect heater hose, and continue filling the engine coolant, if
heater hose is disconnected.
7. Install radiator cap.
8. Install air duct assembly. Refer to EM-16, "
AIR CLEANER AND AIR DUCT" .
9. Warm up until opening thermostat. Standard for warming-up time is approximately 10 minutes at 3,000
rpm.

Make sure thermostat opening condition by touching radiator hose (lower) to see a flow of warm water.
CAUTION:
Watch water temperature gauge so as not to overheat the engine.
10. Stop engine and cool down to less than approximately 50°C (122°F).

Cool down using fan to reduce the time.

If necessary, refill radiator up to filler neck with engine coolant.
11. Refill reservoir tank to “MAX” level line with engine coolant.
12. Repeat steps 6 through 11 two or more times with radiator cap installed until engine coolant level no
longer drops.
13. Check cooling system for leaks with engine running.
14. Warm up engine, and check for sound of engine coolant flow while running engine from idle up to 3,000
rpm with heater temperature controller set at several position between “COOL” and “WARM”.

Sound may be noticeable at heater unit.
15. Repeat step 14 three times.
16. If sound is heard, bleed air from cooling system by repeating steps 6 through 11 until engine coolant level
no longer drops.
FLUSHING COOLING SYSTEM
1. Install reservoir tank if removed. Refer to CO-11, "RADIATOR" .
2. Install radiator drain plug.
PBIC3802E
SM A18 2B

CO-16Revision: June 2006
COOLING FAN
2007 Versa
Removal and InstallationEBS00U83
REMOVAL
1. Drain engine coolant from radiator. Refer to CO-8, "DRAINING ENGINE COOLANT" .
CAUTION:

Perform this step when engine is cold.

Do not spill engine coolant on drive belt.
2. Remove air duct (inlet). Refer to EM-16, "
Components" .
3. Remove reservoir tank. Refer to CO-11, "
Components" .
4. Disconnect radiator hose (upper) at radiator side. Refer to CO-11, "
Components" .
5. Disconnect harness connectors from fan motor, and move harness to aside.
6. Remove cooling fan assembly.
CAUTION:
Be careful not to damage or scratch the radiator core.
INSTALLATION
Installation is the reverse order of removal.

Cooling fans are controlled by ECM. For details, refer to EC-443, "DTC P1217 ENGINE OVER TEMPER-
AT U R E" .
CAUTION:
Be careful not to damage or scratch the radiator core.
DISASSEMBLY AND ASSEMBLYEBS00V62
DISASSEMBLY
1. Remove cooling fan from fan motor.
2. Remove fan motor from fan shroud.
INSPECTION AFTER DISASSEMBLY
Inspect cooling fan for crack or unusual bend.

If anything is found, replace cooling fan.
ASSEMBLY
Assembly is the reverse order of disassembly.

CO-20Revision: June 2006
WATER OUTLET AND WATER CONTROL VALVE
2007 Versa
WATER OUTLET AND WATER CONTROL VALVEPFP:11060
ComponentsEBS00U86
Removal and InstallationEBS00U87
REMOVAL
1. Drain engine coolant. Refer to CO-8, "DRAINING ENGINE COOLANT" .
CAUTION:
Perform this step when the engine is cold.
2. Remove air duct. Refer to EM-16, "
Components" .
3. Remove radiator hose (upper). Refer to CO-11, "
Components" .
4. Remove heater hoses and water hoses.
5. Remove water outlet.
6. Remove water control valve.
7. Remove engine coolant temperature sensor, if necessary.
CAUTION:

Handle carefully to avoid any shock to engine coolant temperature sensor.

Replace the gasket with a new one.
1. Engine coolant temperature sensor 2. Rubber ring 3. Water control valve
4. Gasket 5. Water hose 6. Gasket
7. Water hose 8. Water outlet 9. Heater hose
10. Heater hose 11. Radiator hose (upper) Front
A. To heater B. To electric throttle control actuator C. To radiator
PBIC4699E

CO-22Revision: June 2006
WATER OUTLET AND WATER CONTROL VALVE
2007 Versa
Water H oses
Install water hoses (3),(5) as shown.

Electric throttle control actuator (1)

Clamp (2)

Water outlet (4)

Paint mark (A)

Clamp shall not interfere with the bulged area (B)
INSPECTION AFTER INSTALLATION

Check for leaks of engine coolant. Refer to CO-8, "Inspection" .

Start and warm up the engine. Visually check if there is no leaks of engine coolant.
PBIC4703E

SERVICE DATA AND SPECIFICATIONS (SDS)
CO-23
C
D
E
F
G
H
I
J
K
L
MA
CO
Revision: June 20062007 Versa
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
Standard and LimitEBS00T7Q
CAPACITY
Unit: (US qt, lmp qt)
THERMOSTAT
WATER CONTROL VALVE
RADIATOR
Unit: kPa (bar, kg/cm2 , psi)
Engine coolant capacity (with reservoir tank at “MAX” level) Approx. 6.8 (7 1/4, 6.0)
Valve opening temperature 80.5 - 83.5°C (177 - 182°F)
Maximum valve lift 8 mm/ 95°C (0.315 in/ 203°F)
Valve closing temperature 77°C (171°F)
Valve opening temperature 93.5 - 96.5°C (200 - 206°F)
Maximum valve lift 8 mm/ 108°C (0.315 in/ 226°F)
Valve closing temperature 90°C (194°F)
Cap relief pressureStandard 78 - 98 (0.78 - 0.98, 0.8 - 1.0, 11- 14)
Limit 59 (0.59, 0.6, 9)
Leakage test pressure 157 (1.57, 1.6, 23)

CVT-1
CVT
C TRANSMISSION/TRANSAXLE
CONTENTS
D
E
F
G
H
I
J
K
L
M
SECTION CVT
A
B
CVT
Revision: June 20062007 Versa INDEX FOR DTC ........................................................ 6
Alphabetical Index .................................................... 6
DTC No. Index ......................................................... 7
PRECAUTIONS .......................................................... 8
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 8
Precautions Necessary for Steering Wheel Rotation
After Battery Disconnect .......................................... 8
OPERATION PROCEDURE ................................. 8
Precautions for On Board Diagnostic (OBD) System
of CVT and Engine ................................................... 9
Service After Replacing TCM and Transaxle
Assembly .................................................................. 9
SERVICE AFTER REPLACING TCM AND
TRANSAXLE ASSEMBLY ..................................... 9
PATTERN A .......................................................... 9
PATTERN B .......................................................... 9
PATTERN C .........................................................11
Removal and Installation Procedure for CVT Unit
Connector ................................................................11
REMOVAL ............................................................11
INSTALLATION ................................................... 12
Precautions ............................................................ 13
Service Notice or Precautions ................................ 13
CVT FLUID COOLER SERVICE ......................... 13
OBD-II SELF-DIAGNOSIS .................................. 14
PREPARATION ......................................................... 15
Special Service Tools ............................................. 15
Commercial Service Tools ...................................... 15
CVT FLUID ............................................................... 16
Checking CVT Fluid ............................................... 16
FLUID LEVEL CHECK ........................................ 16
FLUID CONDITION CHECK ............................... 17
Changing CVT Fluid ............................................... 17
CVT Fluid Cooler Cleaning .................................... 18
CVT FLUID COOLER CLEANING PROCEDURE
... 18
CVT FLUID COOLER DIAGNOSIS PROCE-DURE .................................................................. 19
CVT FLUID COOLER INSPECTION PROCE-
DURE .................................................................. 20
CVT FLUID COOLER FINAL INSPECTION ........ 20
CVT SYSTEM ............................................................ 21
Cross-sectional View - RE0F08A ........................... 21
Control System ....................................................... 22
Hydraulic Control System ....................................... 23
TCM Function ......................................................... 24
CONTROL SYSTEM OUTLINE .......................... 24
CONTROL SYSTEM DIAGRAM ......................... 24
CAN Communication .............................................. 25
SYSTEM DESCRIPTION .................................... 25
Input/Output Signal of TCM .................................... 25
Line Pressure and Secondary Pressure Control .... 26
NORMAL CONTROL .......................................... 26
FEEDBACK CONTROL ...................................... 26
Shift Control ............................................................ 26
“D” POSITION ..................................................... 27
OVERDRIVE-OFF MODE ................................... 27
“L” POSITION ...................................................... 27
DOWNHILL ENGINE BRAKE CONTROL (AUTO
ENGINE BRAKE CONTROL) .............................. 27
ACCELERATION CONTROL .............................. 27
Lock-up and Select Control .................................... 28
TORQUE CONVERTER CLUTCH AND SELECT
CONTROL VALVE CONTROL ............................ 28
Control Valve .......................................................... 29
FUNCTION OF CONTROL VALVE ..................... 29
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 30
Introduction ............................................................. 30
OBD-II Function for CVT System ........................... 30
One or Two Trip Detection Logic of OBD-II ............ 30
ONE TRIP DETECTION LOGIC ......................... 30
TWO TRIP DETECTION LOGIC ......................... 30
OBD-II Diagnostic Trouble Code (DTC) ................. 30
HOW TO READ DTC AND 1ST TRIP DTC ......... 30
HOW TO ERASE DTC ........................................ 31
HOW TO ERASE DTC (WITH CONSULT-II) ....... 32