fog light bulb NISSAN TIIDA 2007 Service Repair Manual

LT-2Revision: June 20062007 Versa Daytime Light Control Does Not Operate Properly
(High Beam Headlamps Operate Properly) ............ 35
Aiming Adjustment .................................................. 37
PREPARATION BEFORE ADJUSTING .............. 37
LOW BEAM AND HIGH BEAM ........................... 37
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ............ 38
Bulb Replacement .................................................. 39
HEADLAMP (HIGH/LOW) ................................... 39
PARKING (CLEARANCE) LAMP ......................... 39
FRONT TURN SIGNAL LAMP ............................ 39
Removal and Installation ........................................ 39
REMOVAL ........................................................... 39
INSTALLATION .................................................... 39
Disassembly and Assembly .................................... 40
DISASSEMBLY ................................................... 40
ASSEMBLY ......................................................... 40
FRONT FOG LAMP .................................................. 41
Component Parts and Harness Connector Location ... 41
System Description ................................................. 41
OUTLINE ............................................................. 41
FOG LAMP OPERATION .................................... 42
COMBINATION SWITCH READING FUNCTION ... 42
EXTERIOR LAMP BATTERY SAVER CONTROL ... 42
CAN Communication System Description .............. 42
Wiring Diagram — F/FOG — .................................. 43
Terminals and Reference Values for BCM .............. 45
Terminals and Reference Values for IPDM E/R ...... 45
How to Proceed With Trouble Diagnosis ................ 45
Preliminary Check .................................................. 45
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR BCM ................................................... 45
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR IPDM E/R ........................................... 45
CONSULT-II Function (BCM) .................................. 45
CONSULT-II Function (IPDM E/R) .......................... 45
Front Fog lamps Do Not Illuminate (Both Sides) .... 45
Front Fog Lamp Does Not Illuminate (One Side) ... 48
Aiming Adjustment .................................................. 49
Bulb Replacement .................................................. 49
Removal and Installation ........................................ 50
REMOVAL ........................................................... 50
INSTALLATION .................................................... 50
TURN SIGNAL AND HAZARD WARNING LAMPS ... 51
Component Parts and Harness Connector Location ... 51
System Description ................................................. 51
TURN SIGNAL OPERATION ............................... 51
HAZARD LAMP OPERATION ............................. 52
REMOTE KEYLESS ENTRY SYSTEM OPERA-
TION .................................................................... 53
COMBINATION SWITCH READING FUNCTION ... 53
CAN Communication System Description .............. 53
Schematic ............................................................... 54
Wiring Diagram — TURN — ................................... 55
Terminals and Reference Values for BCM .............. 59
How to Proceed With Trouble Diagnosis ................ 59
Preliminary Check .................................................. 59
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR BCM ................................................... 59CONSULT-II Function (BCM) ..................................59
Turn Signals Do Not Operate ..................................59
Front Turn Signal Lamp Does Not Operate ............59
Rear Turn Signal Lamp Does Not Operate .............60
Hazard Warning Lamp Does Not Operate But Turn
Signal Lamp Operates ............................................62
Turn Signal Indicator Lamp Does Not Operate .......63
Bulb Replacement of Front Turn Signal Lamp ........64
Bulb Replacement of Rear Turn Signal Lamp .........64
Removal and Installation of Front Turn Signal Lamp ...64
Removal and Installation of Rear Turn Signal Lamp ...64
LIGHTING AND TURN SIGNAL SWITCH ................65
Removal and Installation .........................................65
REMOVAL ............................................................65
INSTALLATION ....................................................65
HAZARD SWITCH .....................................................66
Removal and Installation .........................................66
REMOVAL ............................................................66
INSTALLATION ....................................................66
COMBINATION SWITCH ..........................................67
Wiring Diagram — COMBSW — ............................67
Combination Switch Reading Function ...................68
Terminals and Reference Values for BCM ..............68
CONSULT-II Function (BCM) ..................................68
Combination Switch Inspection ...............................68
Removal and Installation .........................................70
STOP LAMP ..............................................................71
Wiring Diagram — STOP/L — ................................71
Bulb Replacement of High-Mounted Stop Lamp .....72
Bulb Replacement of Rear Combination Lamp for
Stop Lamp ...............................................................72
Removal and Installation of High-Mounted Stop
Lamp .......................................................................72
REMOVAL ............................................................72
INSTALLATION ....................................................72
Removal and Installation of Rear Combination
Lamp for Stop Lamp ................................................72
BACK-UP LAMP .......................................................73
Wiring Diagram — BACK/L — ................................73
Bulb Replacement ...................................................74
Removal and Installation .........................................74
PARKING, LICENSE PLATE AND TAIL LAMPS ......75
Component Parts and Harness Connector Location ...75
System Description .................................................75
OPERATION BY LIGHTING SWITCH .................75
COMBINATION SWITCH READING FUNCTION ...76
EXTERIOR LAMP BATTERY SAVER CONTROL ...76
CAN Communication System Description ..............76
Schematic ...............................................................77
Wiring Diagram — TAIL/L — ...................................78
Terminals and Reference Values for BCM ..............81
Terminals and Reference Values for IPDM E/R ......81
How to Proceed With Trouble Diagnosis ................81
Preliminary Check ...................................................81
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR BCM ...................................................81
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR IPDM E/R ...........................................81
CONSULT-II Function (BCM) ..................................81

FRONT FOG LAMP
LT-49
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa
Aiming AdjustmentEKS00HXJ
The front fog lamp is a semi-sealed beam type which uses a replaceable halogen bulb. Before performing
aiming adjustment, make sure of the following.

Keep all tires inflated to correct pressure.

Place vehicle on level surface.

Set that there is no-load in vehicle other than the driver (or equivalent weight placed in driver’s position).
Coolant, engine oil filled up to correct level and full fuel tank.
Adjust aiming in the vertical direction by turning the adjusting screw (A).
1. Set the distance (C) between the screen and the center of front
fog lamp lens (E) as shown.
2. Turn front fog lamps (1) to ON.
3. Adjust front fog lamps using adjusting screw so that the top edge
of the high intensity zone (A) is as shown.
NOTE:
When performing adjustment, if necessary, cover the headlamps
and opposite front fog lamp.
Bulb ReplacementEKS00HXK
1. Turn lighting switch OFF.
2. Turn off the fender protector (front) to obtain work space
between the fender protector and fender.
3. Disconnect front fog lamp connector (1).
4. Turn bulb socket (2) counterclockwise unlock and remove it.
5. Remove bulb from its socket.
PKIC1070E
Aiming distance from center of fog lamp to screen (C) 25,000 mm (984.3 in)
Foglamp beam width (D) 870 mm (34.3 in)
Horizontal distance from ground to bottom edge of high
intensity zone (B)220 mm (8.7 in)
Horizontal distance from bottom edge to top edge of
high intensity zone (A)21.75 mm (0.9 in)
WKIA5419E
PKIC1071E