lock NISSAN TIIDA 2007 Service Repair Manual

TM-660
< DISASSEMBLY AND ASSEMBLY >[5MT: RS5F91R]
FINAL DRIVE
 Check side gears, thrust washers, pinion mate shaft, pinion mate
gears, lock ring and differential case. If necessary, replace with a
new one.
BEARING
 Check for bearing damage and rough rotation. If necessary,
replace with a new one.
CAUTION:
When replacing tapered roller bearing, replace outer and inner
races as a set.
PCIB0977J
SPD715

CONTROL LINKAGE
TM-675
< ON-VEHICLE REPAIR >[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
3. Disconnect connectors (A) and then remove bracket (1).
4. While pressing the lock of the select cable in the direction of the
arrow shown, remove the select cable from the selector lever.
5. While pressing the lock of the shift cable in the direction of the
arrow shown, remove the shift cable from the shifter lever.
6. While pulling the lock of the select cable in the direction of the
arrow shown, remove the select cable from the cable mounting
bracket.
7. While pulling the lock of the shift cable in the direction of the
arrow shown, remove the shift cable from the cable mounting
bracket.
8. Remove the control lever knob.
9. Remove console finisher assembly and the center console
assembly. Refer to IP-11, "
Removal and Installation".
10. Shift the control lever to the neutral position.
11. While pressing the lock of the select cable in the direction of the
arrow shown, remove the select cable from the control device
assembly.
12. While pressing the lock of the shift cable in the direction of the
arrow shown, remove the shift cable from the control device
assembly.
13. While pulling the lock of the select cable in the direction of the
arrow shown, remove the select cable from the control device
assembly.
14. While pulling the lock of the shift cable in the direction of the
arrow shown, remove the shift cable from the control device
assembly.
15. Remove the control device assembly.
16. Remove the heat plate.
17. Remove the bracket.
JPDIA0240ZZ
JPDIC0066ZZ
JPDIC0067ZZ
JPDIC0066ZZ
JPDIC0067ZZ

TM-676
< ON-VEHICLE REPAIR >[6MT: RS6F94R]
CONTROL LINKAGE
18. Remove the grommet and then remove the shift cable and select cable from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
 Shift the control lever to the neutral position.
 Securely assemble each cable and the selector lever and shifter lever.
 Securely assemble each cable and the cable mounting bracket.
 Securely assemble each cable and the control device assembly.
 Make sure that the claws of grommet are in contact with the floor.
 Be careful about the installation direction and push the control lever knob into the control lever.
CAUTION:
Never reuse control lever knob.
 Tapping work for tapping bolt is not applied to new clutch housing. Do not perform tapping by other than
screwing tapping bolt because tapping is formed by screwing tapping bolt into clutch housing.
CAUTION:
Never reuse tapping bolt.
Install the select cable (the control device assembly side) with the following procedure.
1. While pulling the lock of the select cable in the direction of the
arrow shown, install the select cable to the control device
assembly.
2. Slide the lock (1) of the select cable in the direction of the arrow
as shown to pull up the stopper (2) of the select cable.
3. Install the end of the select cable to the pin of the control device
assembly.
4. Install the lever stopper pin (1) or a pin [3 mm (0.12 in) dia.] to
the control device assembly.
CAUTION:
Select cable cannot be adjusted accurately without a use of
a lever stopper pin or a pin [3 mm (0.12 in) dia.].
NOTE:
A lever stopper pin is not included in control device assembly.
Therefore, if the control device assembly is not replaced, pre-
pare a pin [3 mm (0.12 in) dia.].
5. Check that the control lever does not move in the direction of the
select. If it moves, repeat step 3.
6. Shift the control lever to 4th gear position.
JPDIC0067ZZ
JPDIC0064ZZ
JPDIC0069ZZ

CONTROL LINKAGE
TM-677
< ON-VEHICLE REPAIR >[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
7. With the stopper (1) of the select cable pressed into all the way,
slide lock (2) of the select cable all the way in the direction of the
arrow.
8. Remove the lever stopper pin or a pin [3 mm (0.12 in) dia.] from
the control device assembly.
9. Shift the control lever to each gear position to check that there is
no binding. If any, repeat step 3.
InspectionINFOID:0000000001381640
After installing, confirm the following items:
 When the control lever is shifted to 1st-2nd side and 5th-6th side, confirm the control lever returns to neutral
position smoothly.
 When the control lever is shifted to each position, make sure there is no binding or disconnection in each
boot.
JPDIC0065ZZ

AIR BREATHER HOSE
TM-679
< ON-VEHICLE REPAIR >[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P MR18DE Engine Models
1. Remove the battery. Refer to PG-6, "Removal and Installation".
2. Remove air duct and air cleaner case. Refer to EM-269, "
Removal and Installation".
3. Remove the air breather hose.
CAUTION:
When removing air breather hose, be sure to hold two way connector securely.
K9K Engine Models
1. Remove the air duct.
2. Remove the air breather hose.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Make sure air breather hose is not collapsed or blocked due to folding or bending when installed.
MR18DE Engine Models
 When installing air breather hose on two way connector, aim paint mark face toward the vehicle front.
 When installing air breather hose on two way connector, push it until it hits transaxle case.
 When installing air breather hose to air cleaner case, make sure that clips are fully inserted.
K9K Engine Models
 When installing air breather hose to transaxle, aim paint mark face toward the vehicle front.
 When installing air breather hose to transaxle, push it until it hits transaxle case.
 When installing air breather hose to air duct, make sure that clip is fully inserted.

TM-686
< DISASSEMBLY AND ASSEMBLY >[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
SHIFT FORK AND FORK ROD
1. Reverse output gear 2. Snap ring 3. Reverse baulk ring
4. Return spring 5. Needle bearing 6. Reverse idler shaft
7. Seal washer 8. Washer 9. Reverse input gear
10. Lock washer 11. Spring washer
SFIA3294E

TM-688
< DISASSEMBLY AND ASSEMBLY >[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
Disassembly
INFOID:0000000001381646
1. Drain the oil from the transaxle. Refer to TM-672, "Draining".
2. Remove filler plug and gasket from transaxle case.
3. Remove shift lever retaining pin (1) and shifter lever using suit-
able tool.
4. Remove bracket (2) and position switch (3) from transaxle case.
1. Side gear 2. Pinion mate gear 3. Thrust washer
4. Pinion mate shaft 5. shim 6. Differential side bearing outer race
(transaxle case side)
7. Differential side bearing inner race
(transaxle case side)8. Final gear 9. Differential case
10. Speedometer drive gear 11. Lock ring 12. Differential side bearing inner race
(clutch housing side)
13. Differential side bearing outer race
(clutch housing side)
: Replace the parts as a set.
SFIA3296E
PCIB1693E

REVERSE IDLER SHAFT AND GEAR
TM-709
< DISASSEMBLY AND ASSEMBLY >[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
REVERSE IDLER SHAFT AND GEAR
Exploded ViewINFOID:0000000001381656
Refer to TM-635, "Exploded View".
DisassemblyINFOID:0000000001381657
1. Remove reverse output gear (1).
2. Remove snap ring (1).
3. Remove reverse baulk ring (1) and return spring (2).
4. Remove snap ring (1), lock washer (2), reverse input gear (3)
and washer.
PCIB1760E
PCIB1759E
PCIB1758E
PCIB1757E

FINAL DRIVE
TM-711
< DISASSEMBLY AND ASSEMBLY >[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
FINAL DRIVE
Exploded ViewINFOID:0000000001381659
Refer to TM-635, "Exploded View".
DisassemblyINFOID:0000000001381660
1. Remove differential side bearing inner race (clutch housing side)
(1) using the drift (A) [SST: ST33061000] and a puller.
2. Remove speedometer drive gear.
3. Remove final gear mounting bolts (1), and then separate the
final gear (2) from differential case.
4. Remove differential side bearing inner race (transaxle case
side) (1) using the drift (A) [Commercial service tool] and a suit-
able puller.
5. Remove lock ring (1) from differential case.
6. Remove pinion mate shaft, pinion mate gears, side gears and
thrust washer from differential case.
AssemblyINFOID:0000000001381661
1. Install pinion mate shaft, pinion mate gears, side gears and thrust washer into differential case.
PCIB1767E
PCIB1766E
JPDIC0114ZZ
PCIB1764E

TM-712
< DISASSEMBLY AND ASSEMBLY >[6MT: RS6F94R]
FINAL DRIVE
2. Install lock ring (1) onto differential case.
CAUTION:
Make sure that lock ring is securely installed in the groove.
3. Install final gear into differential case, and tighten final gear
mounting bolts to the specified torque.
4. Install speedometer drive gear onto differential case.
5. Press-fit the differential side bearing inner race (clutch housing
side) onto the differential case using the drift (A) [Commercial
service tool] and press.
CAUTION:
Replace differential side bearing inner race and differential
side bearing outer race as a set.
6. Press-fit the differential side bearing inner race (transaxle case
side) onto the differential case using the drift (A) [Commercial
service tool] and press.
CAUTION:
Replace differential side bearing inner race and differential
side bearing outer race as a set.
InspectionINFOID:0000000001381662
GEAR, WASHER, SHAFT AND CASE
Check side gears, thrust washer, pinion mate shaft, pinion mate
gears, lock ring and differential case. If necessary, replace with a
new one.
BEARING
PCIB1764E
JPDIC0115ZZ
JPDIC0116ZZ
PCIB0977J