Instrument panel NISSAN TIIDA 2007 Service Owner's Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2007, Model line: TIIDA, Model: NISSAN TIIDA 2007Pages: 5883, PDF Size: 78.95 MB
Page 806 of 5883
HOOD
DLK-217
< REMOVAL AND INSTALLATION >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
5. Remove hood opener on bottom left of instrument panel, and
then remove hood lock cable.
6. Remove grommet on lower dashboard, and pull out hood lock
cable from passenger room side.
CAUTION:
While pulling the cable, be careful not to damage (peel)
hood opener cable outer surface on edges of body through
hole.
INSTALLATION
Installation is in the reverse order of removal.
Perform hood fitting adjustment. Refer to DLK-213, "
Fitting Adjustment".
Hood Lock Reinforcement
When installing hood lock reinforcement, loosen hood bolts, and
then tighten bolts in the order as shown.
Hood Lock Cable
1. Pull the hood lock cable through the panel hole to the engine compartment.
CAUTION:
Be careful not to bend the cable too much, keeping the
radius 100 mm (3.94 in) or more.
2. Check that the cable is not offset from the positioning grommet,
and push the grommet into the panel hole securely.
3. Apply the sealant around the grommet (at * mark).
4. Install cable securely to lock.
5. After installing, check hood lock adjustment and hood opener
operation.
Hood Lock Control InspectionINFOID:0000000001315834
CAUTION:
If the hood lock cable is bent or deformed, replace it.
LIIA2667E
23.6 N·m (2.4 kg-m, 17 ft-lb)
PIIB6513E
PIIB5801E
PIIB6537E
Page 835 of 5883
DLK-246
< FUNCTION DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
DOOR LOCK FUNCTION
DOOR LOCK AND UNLOCK SWITCH : Component Parts Location
INFOID:0000000001396672
1. BCM M18, M19, M20
(view with glove box removed)2. Intelligent Key unit M52 3. Front door switch (driver side) B34
(Passenger side) B27
4. Front door lock actuator (driver side) D14
(Passenger side) D114
Door unlock sensor (driver side) D145. Rear door switch LH B71
RH B536. Rear door lock actuator LH D205
RH D305
7. Key switch and ignition knob switch (A/T)
M328. Key switch and ignition knob switch
(M/T) M329. Instrument panel warning lamp as-
sembly (door lock) M37
ALKIA0811ZZ
Page 839 of 5883
DLK-250
< FUNCTION DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
DOOR LOCK FUNCTION
ALKIA0815ZZ
1. Combination meter M24 2. Key warning lamp (combination meter) 3. Lock warning lamp (combination meter)
4. Stop lamp switch E13
(view with instrument panel LH re-
moved)5. Steering lock solenoid M6
(bottom view of steering column)6. Key switch and ignition knob switch (A/
T) M32
7. Key switch and ignition knob
switch (M/T) M328. Instrument panel antenna M10
(view with glove box removed)9. BCM M18, M19, M20
10. Intelligent Key Unit M52 11. Intelligent key warning buzzer (driver side)
D6 (view with front door finisher removed)12. Front outside antenna (driver side) D10
(Passenger side) D106
13. Front door request switch (driver
side) D5
(Passenger side) D10314. Door unlock sensor D14
[Front door lock actuator (driver side)]15. Front door switch (driver side) B34
(Passenger side) B29
16. Front console antenna B45
(view with front console removed)17. Rear door switch LH B71
RH B5318. Rear floor antenna B46
(behind rear seat)
19. Trunk request switch B67
(sedan)20. Rear bumper antenna B81
(view with rear fascia removed)21. Intelligent Key warning buzzer (trunk)
B82 (sedan)
(view with trunk finisher LH removed)
22. Back door request switch D406
(hatchback)23. Back door lock assembly (back door switch)
D405 (hatchback view with back door open)
Page 843 of 5883
DLK-254
< FUNCTION DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
DOOR LOCK FUNCTION
ALKIA0815ZZ
1. Combination meter M24 2. Key warning lamp (combination meter) 3. Lock warning lamp (combination meter)
4. Stop lamp switch M203
(view with instrument panel LH re-
moved)5. Steering lock solenoid M6
(bottom view of steering column)6. Key switch and ignition knob switch (A/
T) M32
7. Key switch and ignition knob
switch (M/T) M328. Instrument panel antenna M10
(view with glove box removed)9. BCM M18, M19, M20
10. Intelligent Key Unit M52 11. Intelligent key warning buzzer (driver side)
D6 (view with front door finisher removed)12. Front outside antenna (driver side) D10
(Passenger side) D106
13. Front door request switch (driver
side) D5
(Passenger side) D10314. Door unlock sensor D14
[Front door lock actuator (driver side)]15. Front door switch (driver side) B34
(Passenger side) B29
16. Front console antenna B45
(view with front console removed)17. Rear door switch LH B71
RH B5318. Rear floor antenna B46
(behind rear seat)
19. Trunk request switch B67
(sedan)20. Rear bumper antenna B81
(view with rear fascia removed)21. Intelligent Key warning buzzer (trunk)
B82 (sedan)
(view with trunk finisher LH removed)
22. Back door request switch D406
(hatchback)23. Back door lock assembly (back door switch)
D405 (hatchback view with back door open)
Page 845 of 5883
DLK-256
< FUNCTION DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
DOOR LOCK FUNCTION
CAUTION:
The above function operates when the Intelligent Key is inside the vehicle. However, there may be
times when the Intelligent Key can not be detected, and this function will not operate when the Intelli-
gent Key is on the instrument panel, rear parcel shelf or in the glove box. Also, this system some times
does not operate if the Intelligent Key is in the door pocket for the open door.
Operation Operation condition Operation
Driver door closeRight after driver side door is closed under the following con-
ditions
Door lock operation
Driver side door is opened
Driver side door is in unlock state.All doors unlock
Any door open to all door closeRight after all doors are closed under the following condi-
tions
Intelligent Key is inside the vehicle
Any door is opened
All doors are locked by door lock and unlock switch. All doors unlock
Honk Intelligent Key warning
buzzer
Page 847 of 5883
DLK-258
< FUNCTION DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
DOOR LOCK FUNCTION
ALKIA0815ZZ
1. Combination meter M24 2. Key warning lamp (combination meter) 3. Lock warning lamp (combination meter)
4. Stop lamp switch M203
(view with instrument panel LH re-
moved)5. Steering lock solenoid M6
(bottom view of steering column)6. Key switch and ignition knob switch (A/
T) M32
7. Key switch and ignition knob
switch (M/T) M328. Instrument panel antenna M10
(view with glove box removed)9. BCM M18, M19, M20
10. Intelligent Key Unit M52 11. Intelligent key warning buzzer (driver side)
D6 (view with front door finisher removed)12. Front outside antenna (driver side) D10
(Passenger side) D106
13. Front door request switch (driver
side) D5
(Passenger side) D10314. Door unlock sensor D14
[Front door lock actuator (driver side)]15. Front door switch (driver side) B34
(Passenger side) B29
16. Front console antenna B45
(view with front console removed)17. Rear door switch LH B71
RH B5318. Rear floor antenna B46
(behind rear seat)
19. Trunk request switch B67
(sedan)20. Rear bumper antenna B81
(view with rear fascia removed)21. Intelligent Key warning buzzer (trunk)
B82 (sedan)
(view with trunk finisher LH removed)
22. Back door request switch D406
(hatchback)23. Back door lock assembly (back door switch)
D405 (hatchback view with back door open)
Page 857 of 5883
DLK-268
< FUNCTION DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
WARNING FUNCTION
ALKIA0815ZZ
1. Combination meter M24 2. Key warning lamp (combination meter) 3. Lock warning lamp (combination meter)
4. Stop lamp switch M203
(view with instrument panel LH re-
moved)5. Steering lock solenoid M6
(bottom view of steering column)6. Key switch and ignition knob switch (A/
T) M32
7. Key switch and ignition knob
switch (M/T) M328. Instrument panel antenna M10
(view with glove box removed)9. BCM M18, M19, M20
10. Intelligent Key Unit M52 11. Intelligent key warning buzzer (driver side)
D6 (view with front door finisher removed)12. Front outside antenna (driver side) D10
(Passenger side) D106
13. Front door request switch (driver
side) D5
(Passenger side) D10314. Door unlock sensor D14
[Front door lock actuator (driver side)]15. Front door switch (driver side) B34
(Passenger side) B29
16. Front console antenna B45
(view with front console removed)17. Rear door switch LH B71
RH B5318. Rear floor antenna B46
(behind rear seat)
19. Trunk request switch B67
(sedan)20. Rear bumper antenna B81
(view with rear fascia removed)21. Intelligent Key warning buzzer (trunk)
B82 (sedan)
(view with trunk finisher LH removed)
22. Back door request switch D406
(hatchback)23. Back door lock assembly (back door switch)
D405 (hatchback view with back door open)
Page 862 of 5883
HAZARD AND BUZZER REMINDER FUNCTION
DLK-273
< FUNCTION DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
PALKIA0815ZZ
1. Combination meter M24 2. Key warning lamp (combination meter) 3. Lock warning lamp (combination meter)
4. Stop lamp switch M203
(view with instrument panel LH re-
moved)5. Steering lock solenoid M6
(bottom view of steering column)6. Key switch and ignition knob switch (A/
T) M32
7. Key switch and ignition knob
switch (M/T) M328. Instrument panel antenna M10
(view with glove box removed)9. BCM M18, M19, M20
10. Intelligent Key Unit M52 11. Intelligent key warning buzzer (driver side)
D6 (view with front door finisher removed)12. Front outside antenna (driver side) D10
(Passenger side) D106
13. Front door request switch (driver
side) D5
(Passenger side) D10314. Door unlock sensor D14
[Front door lock actuator (driver side)]15. Front door switch (driver side) B34
(Passenger side) B29
16. Front console antenna B45
(view with front console removed)17. Rear door switch LH B71
RH B5318. Rear floor antenna B46
(behind rear seat)
19. Trunk request switch B67
(sedan)20. Rear bumper antenna B81
(view with rear fascia removed)21. Intelligent Key warning buzzer (trunk)
B82 (sedan)
(view with trunk finisher LH removed)
22. Back door request switch D406
(hatchback)23. Back door lock assembly (back door switch)
D405 (hatchback view with back door open)
Page 882 of 5883
INSTRUMENT PANEL WARNING LAMP ASSEMBLY
DLK-293
< COMPONENT DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
INSTRUMENT PANEL WARNING LAMP ASSEMBLY
DescriptionINFOID:0000000001396732
The door lock and unlock switch indicates door lock status. The indicator will illuminate when a lock operation
is accomplished, and during this status, if any door is opened, the indicator will turn OFF.
Component Function CheckINFOID:0000000001396733
1.CHECK FUNCTION
With CONSULT-III
Check “DOOR LOCK IND” in “Active Test” mode with CONSULT-III.
Is the inspection result normal?
YES >> Door lock and unlock switch is OK.
NO >> Refer to DLK-293, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000001396734
1.CHECK DOOR LOCK AND UNLOCK SWITCH INDICATOR INPUT SIGNAL
Lock and unlock the door lock system using the main power window and door lock/unlock switch.
Does the door lock system operate properly?
YES >> GO TO 2.
NO >> Repair the power door lock system. Refer to DLK-286, "
DRIVER SIDE :
ComponentFunctionCheck".
2.CHECK DOOR LOCK AND UNLOCK SWITCH INDICATOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Open and keep the driver door open for the duration of this test.
3. Disconnect instrument panel warning lamp assembly.
4. Check voltage between instrument panel warning lamp assem-
bly connector M37 terminals 3 and 5.
Is the inspection result normal?
YES >> Replace instrument panel warning lamp.
NO >> GO TO 3.
Test item Condition
DOOR LOCK IND:ON Illuminated
:OFF Not illuminated
ALKIA0832ZZ
Instrument panel warning lamp assembly connector
ConditionVo l ta g e
(Approx.)
Te r m i n a l s
3 (+) 5(-)Press the door lock switch to the
LOCK positionBattery voltage
Press the door lock switch to the
UNLOCK position0
Page 883 of 5883
DLK-294
< COMPONENT DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
INSTRUMENT PANEL WARNING LAMP ASSEMBLY
3.CHECK DOOR LOCK AND UNLOCK SWITCH INDICATOR INPUT SIGNAL
Check continuity between instrument panel warning lamp assembly
connector M37 terminal 5 and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness ground.
4.CHECK DOOR LOCK AND UNLOCK SWITCH CIRCUIT
1. Disconnect BCM.
2. Check continuity between BCM connector (A) M18 terminal 32
and instrument panel warning lamp assembly connector (B)
M37 terminal 3.
3. Check continuity between BCM connector (A) M18 terminal 32 and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
5.CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
ALKIA0833ZZ
instrument panel warning lamp assembly
connectorTe r m i n a l
GroundContinuity
M37 5 Yes
ALKIA0834ZZ
BCM connector TerminalInstrument panel warning lamp
assembly connectorTerminal Continuity
M18 32 M37 3 Yes
BCM connector Terminal
GroundContinuity
M18 32 No