XX-XX NISSAN TIIDA 2007 Service Owner's Manual

AV-92
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
MICROPHONE SIGNAL CIRCUIT
Are voltage readings as specified?
YES >> Replace NAVI control unit. Refer to XX-XX, "*****".
NO >> Replace microphone. Refer to XX-XX, "*****"
.
Connector(+) (-)
Reference signal
Terminal Terminal
B68 8 7While speaking into MIC
PKIB5037J

AV-108
< SYMPTOM DIAGNOSIS >[AUDIO WITH NAVIGATION]
MULTI AV SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
MULTI AV SYSTEM SYMPTOMS
Symptom TableINFOID:0000000001728767
RELATED TO NAVIGATION
NOTE:
Combined part of AV switch and audio unit.
RELATED TO REAR VIEW MONITOR
Symptoms Check items Possible malfunction location/Action to take
AV switch cannot be operated.
(All switches cannot be operated.)“MULTI AV” is displayed on “SELECT
SYSTEM” screen of CONSULT-III.Perform the self-diagnosis using CONSULT-III.
(AV- 4 8 , "
CONSULT - III Function (MULTI AV)")
“MULTI AV” is not displayed on “SE-
LECT SYSTEM” screen of CON-
SULT-III. NAVI control unit power supply and ground circuit
(AV- 8 0 , "
NAVI CONTROL UNIT : Diagnosis Proce-
dure")
 Perform CAN diagnosis when “Please wait” is indi-
cated on the screen for approximately 120 seconds
after ignition switch ON.
AV switch cannot be operated.
(Only specified switch cannot be
operated.)CONSULT-III self-diagnosis detects
a malfunction.Perform the self-diagnosis using CONSULT-III.
(AV- 4 8 , "
CONSULT - III Function (MULTI AV)")
CONSULT-III self-diagnosis does not
detect a malfunction.Audio unit (XX-XX, "*****"
)
Map screen is not displayed.
(RGB image other than map is
normal.)–Perform the self-diagnosis using CONSULT-III.
(AV- 4 8 , "
CONSULT - III Function (MULTI AV)")
Fuel economy information display
is malfunctioning.–NAVI control unit power supply and ground circuit (Igni-
tion signal) (AV- 8 0 , "
NAVI CONTROL UNIT : Diagnosis
Procedure")
Voice guidance is not heard. – Voice guidance signal circuit
Traffic information (RDS-TMC) is
not received.Radio broadcasts are received. Audio unit (XX-XX, "*****"
)
Radio broadcasts are not received. Radio antenna (XX-XX, "*****"
)
 Antenna feeder (XX-XX, "*****"
)
Symptoms Check items Possible malfunction location/Action to take
Warning message under the dis-
play is not displayed at rear view
monitor image.– Horizontal synchronizing (HP) signal circuit (AV- 8 7 ,
"Diagnosis Procedure")
 Vertical synchronizing (VP) signal circuit (AV- 8 8 , "
Di-
agnosis Procedure")
 RGB area (YS) signal circuit (AV- 8 6 , "
Diagnosis Pro-
cedure")
Camera image is not shown.
(Only warning message under the
display is displayed.)“REAR VIEW CAMERA” is displayed
on “SELECT SYSTEM” screen of
CONSULT-III. Camera image signal circuit (positive circuit)
(Between camera control unit and display unit)
(XX-XX, "*****"
)
 Camera ON signal circuit (XX-XX, "*****"
)
 Camera image signal circuit
(Between rear view camera and camera control unit)
(XX-XX, "*****"
)
“REAR VIEW CAMERA” is not dis-
played on “SELECT SYSTEM”
screen of CONSULT-III.Camera control unit power supply and ground circuit
(XX-XX, "*****"
)
Camera image is rolling. –Camera image signal circuit (negative circuit)
(Between camera control unit and display unit)
(XX-XX, "*****"
)

AV
MULTI AV SYSTEM SYMPTOMS
AV-109
< SYMPTOM DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
RELATED TO AUDIO
RELATED TO RGB IMAGE
RELATED TO VOICE ACTIVATED CONTROL
RELATED TO HANDS FREE PHONE
It cannot be switched to rear view
monitor.CONSULT-III self-diagnosis detects
a malfunction.Perform the self-diagnosis using CONSULT-III (MULTI
AV ) (AV- 4 8 , "CONSULT - III Function (MULTI AV)").
CONSULT-III self-diagnosis does not
detect a malfunction.NAVI control unit reverse signal circuit Symptoms Check items Possible malfunction location/Action to take
Symptom Check items Possible malfunction location / Action to take
Audio sound is not heard.No sound from all speakers Audio unit (XX-XX, "*****"
)
Sound is not heard only from the specif-
ic places (Front RH, rear RH, front LH
and rear LH).Sound signal circuit of suspect system
Symptoms Check items Possible malfunction location/Action to take
Color of RGB image is not proper.Light blue (Cyan) tintRGB signal (R: red) circuit (AV- 8 2 , "
Diagnosis Proce-
dure")
Purple (Magenta) tint and image is
rolling.RGB signal (G: green) circuit (AV- 8 3 , "
Diagnosis Proce-
dure")
Screen looks yellowish.RGB signal (B: blue) circuit (AV- 8 4 , "
Diagnosis Proce-
dure")
 RGB image is too dark.
 RGB image is too fuzzy.– RGB ground circuit
RGB image is not displayed.
(Nothing is displayed on the
screen.)“MULTI AV” is displayed on “SELECT
SYSTEM” screen of CONSULT-III.Perform the self-diagnosis using CONSULT-III (AV- 4 8 ,
"CONSULT - III Function (MULTI AV)").
“MULTI AV” is not displayed on “SE-
LECT SYSTEM” screen of CON-
SULT-III.NAVI control unit power supply and ground circuit (AV-
80, "NAVI CONTROL UNIT : Diagnosis Procedure")
Symptoms Check items Possible malfunction location/Action to take
The voice cannot be controlled
even if the voice control screen is
displayed.Voice sounds at “Speaker Test” and
“Voice Microphone Test” of “Confir-
mation / Adjustment Mode”.NAVI control unit (XX-XX, "*****"
)
Voice does not sound at “Speaker
Test” and “Voice Microphone Test” of
“Confirmation / Adjustment Mode”. MIC. power supply circuit (AV- 9 1 , "
Diagnosis Proce-
dure")
 Shield (MIC.) circuit (AV- 9 1 , "
Diagnosis Procedure")
 MIC. signal circuit (AV- 9 1 , "
Diagnosis Procedure")
The voice cannot be controlled.
(Voice control screen is not dis-
played.)TEL operation screen is displayed by
pressing and holding “ ” switch
of steering wheel switch.NAVI control unit (XX-XX, "*****"
)
 TEL operation screen is not dis-
played by pressing and holding
“ ” switch of steering wheel
switch.
 Other steering wheel switches are
normal.Steering switch (XX-XX, "*****"
)
“BACK”, “VOL UP”, “VOL DOWN”
and “ ” switches of steering
wheel switch are not operated.Steering switch signal B circuit XX-XX, "*****"
(XX-XX,
"*****")
All steering switches are not operat-
ed.Steering switch signal ground circuit (XX-XX, "*****"
)

AV-110
< SYMPTOM DIAGNOSIS >[AUDIO WITH NAVIGATION]
MULTI AV SYSTEM SYMPTOMS
 Check that the cellular phone is corresponding type (Bluetooth® enabled) when the hands free related mal-
function vehicle is in service before performing a diagnosis.
 There is a case that malfunction occurs due to the version change of the phone type, etc. even though it is a
corresponding type. Therefore, confirm it by changing the cellular phone to another corresponding type
phone, and check that it operates normally. It is necessary to distinguish whether the cause is the vehicle or
cellular phone. Check to ensure the customers phone is supported by checking the phone compatibility for
the hands free system.
Trouble diagnosis chart by symptom
RELATED TO STEERING WHEEL SWITCH
Symptoms Check items Possible malfunction location/Action to take
Does not recognize cellular
phone connection.Repeat the registration of cellular phone. NAVI control unit (XX-XX, "*****"
)
Hands free phone cannot be
established. Hands free phone operation can be
made, but the communication cannot
be established.
 Hands free phone operation can be
performed, however, voice between
each other cannot be heard during the
conversation.NAVI control unit (XX-XX, "*****"
)
The other party's voice cannot
be heard by hands free phone.Check the “microphone speaker ”in In-
spection & Adjustment Mode if sound is
heard.NAVI control unit (AV- 4 8 , "
CONSULT - III Function
(MULTI AV)")
Check the “microphone speaker ”in In-
spection & Adjustment Mode if sound is
not heard.TEL voice signal circuit
Originating sound is not heard
by the other party with hands
free phone communication.Sound operation function is normal. NAVI control unit (XX-XX, "*****"
)
Sound operation function does not work.Microphone signal circuit (AV- 9 1 , "
Diagnosis Proce-
dure")
Symptoms Possible malfunction location/Action to take
All steering switches are not operated. Steering switch signal ground circuit (XX-XX, "*****"
)
Only specified switch cannot be operated. Steering switch (XX-XX, "*****"
)
“ENTER”, “MENU UP”, “MENU DOWN” and “SOURCE”
switches are not operated.Steering switch signal A circuit (XX-XX, "*****"
)
“BACK”, “ ”, “VOL UP” and “VOL DOWN” switches are
not operated.Steering switch signal B circuit (XX-XX, "*****"
)

BRC-8
< BASIC INSPECTION >[ABS]
DIAGNOSIS AND REPAIR WORKFLOW
2.PERFORM THE SELF-DIAGNOSIS
Check the DTC display with the self-diagnosis function. Refer to BRC-25, "
CONSULT-III Function (ABS)".
Is there any DTC displayed?
YES >> GO TO 3
NO >> GO TO 4
3.PERFORM THE SYSTEM DIAGNOSIS
Perform the diagnosis applicable to the displayed DTC. Refer to BRC-71, "
DTC No. Index".
>> GO TO 7
4.CHECK THE SYMPTOM THAT IS NOT CONSIDERED A SYSTEM MALFUNCTION
Check that the symptom is a normal operation that is not considered a system malfunction. Refer to BRC-79,
"Description".
Is the symptom a normal operation?
YES >> INSPECTION END
NO >> GO TO 5
5.CHECK THE WARNING LAMP AND INDICATOR LAMP FOR ILLUMINATION
Check that the warning lamp and indicator lamp illuminate.
• ABS warning lamp: Refer to BRC-60, "
Description".
 Brake warning lamp: Refer to BRC-61, "
Description".
 VDC OFF indicator lamp: Refer to XX-XX, "*****"
.
 SLIP indicator lamp: Refer to XX-XX, "*****"
.
Is ON/OFF timing normal?
YES >> GO TO 6
NO >> GO TO 2
6.PERFORM THE DIAGNOSIS BY SYMPTOM
Perform the diagnosis applicable to the symptom.
>> GO TO 7
7.REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the specified malfunctioning parts.
>> GO TO 8
8.FINAL CHECK
Perform the self-diagnosis again, and check that the malfunction is repaired completely. After checking, erase
the self-diagnosis memory. Refer to BRC-25, "
CONSULT-III Function (ABS)".
Is no other DTC present and the repair completed?
YES >> INSPECTION END
NO >> GO TO 3

VDC
BRC-15
< FUNCTION DIAGNOSIS >[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
Component DescriptionINFOID:0000000001731211
1. Front wheel sensor
LH E18
RH E1172. ABS actuator and electric unit (con-
trol unit) E1253. Combination meter M24
4. Rear wheel sensor
LH C11
RH C105. Yaw rate/side/decel G sensor M108 6. Steering angle sensor M17 (view
with steering wheel removed)
7. VDC OFF switch M257 8. Active booster E49 9. Delta stroke sensor E114
10. Brake fluid level switch E21 11. Front pressure sensor E31 12. Rear pressure sensor E32
Component parts Reference
ABS actuator and electric unit (control unit)Pump
BRC-39, "
Description"Motor
Actuator relayBRC-54, "
Description"
Solenoid valveBRC-46, "Description"
VDC switch-over valve
(CV1, CV2, SV1, SV2)XX-XX, "*****"
Wheel sensorBRC-30, "Description"
Yaw rate/side/decel G sensorXX-XX, "*****"
Steering angle sensorXX-XX, "*****"
VDC OFF switchXX-XX, "*****"
ABS warning lampBRC-60, "Description"
Brake warning lampBRC-61, "Description"
VDC OFF indicator lampXX-XX, "*****"
SLIP indicator lampXX-XX, "*****"
Front pressure sensor
XX-XX, "*****"
Rear pressure sensor
Active boosterXX-XX, "*****"
Delta stroke sensorXX-XX, "*****"

BRC-18
< FUNCTION DIAGNOSIS >[ABS]
TCS
Component Description
INFOID:0000000001731215
1. Front wheel sensor
LH E18
RH E1172. ABS actuator and electric unit (con-
trol unit) E1253. Combination meter M24
4. Rear wheel sensor
LH C11
RH C105. Yaw rate/side/decel G sensor M108 6. Steering angle sensor M17 (view
with steering wheel removed)
7. VDC OFF switch M257 8. Active booster E49 9. Delta stroke sensor E114
10. Brake fluid level switch E21 11. Front pressure sensor E31 12. Rear pressure sensor E32
Component parts Reference
ABS actuator and electric unit (control unit)Pump
BRC-39, "
Description"Motor
Actuator relayBRC-54, "
Description"
Solenoid valveBRC-46, "Description"
VDC switch-over valve
(CV1, CV2, SV1, SV2)XX-XX, "*****"
Wheel sensorBRC-30, "Description"
Yaw rate/side/decel G sensorXX-XX, "*****"
Steering angle sensorXX-XX, "*****"
VDC OFF switchXX-XX, "*****"
ABS warning lampBRC-60, "Description"
Brake warning lampBRC-61, "Description"
VDC OFF indicator lampXX-XX, "*****"
SLIP indicator lampXX-XX, "*****"
Front pressure sensor
XX-XX, "*****"
Rear pressure sensor
Active boosterXX-XX, "*****"
Delta stroke sensorXX-XX, "*****"

BRC-66
< ECU DIAGNOSIS >[ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
NOTE:
 1: Confirm tire pressure is normal.
 2: Only 4WD models.
 3: On and off timing for warning lamp and indicator lamp.
- ABS warning lamp: Refer to BRC-60, "
Description".
- Brake warning lamp: Refer to BRC-61, "
Description".
- VDC OFF indicator lamp: Refer to XX-XX, "*****"
.
- SLIP indicator lamp: Refer to XX-XX, "*****"
.
TERMINAL LAYOUT
DELTA S SEN Value detected by delta stroke sensorWhen brake pedal is depressed 1.05 - 1.80 mm
When brake pedal is released 0.00 mm (+0.6/-0.4)
RELEASE SWITCH
NO Active booster signal statusWhen brake pedal is depressed ON
When brake pedal is released OFF
RELEASE SWITCH
NC Active booster signal statusWhen brake pedal is depressed OFF
When brake pedal is released ON Monitor item Display contentData monitor
ConditionReference value in
normal operation
AWFIA0032ZZ

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-71
< ECU DIAGNOSIS >[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
In case of an electrical malfunction with the ABS, the ABS warning lamp, VDC OFF indicator lamp and SLIP
indicator lamp will turn on. In case of an electrical malfunction with the EBD system, the BRAKE warning lamp,
ABS warning lamp, VDC OFF indicator lamp and SLIP indicator lamp will turn on.
The system will revert to one of the following conditions of the Fail-Safe function.
1. For ABS malfunction, only the EBD is operative and the condition of the vehicle is the same condition of
vehicles without ABS/TCS/VDC system.
2. For EBD malfunction, the EBD and ABS become inoperative, and the condition of the vehicle is the same
as the condition of vehicles without ABS/TCS/VDC or EBD system.
VDC/TCS SYSTEM
In case of TCS/VDC system malfunction, the VDC OFF indicator lamp and SLIP indicator lamp are turned on
and the condition of the vehicle is the same as the condition of vehicles without TCS/VDC system. In case of
an electrical malfunction with the TCS/VDC system, the ABS control continues to operate normally without
TCS/VDC control.
DTC No. IndexINFOID:0000000001731342
DTC Items (CONSULT screen terms) Reference
C1101 RR RH SENSOR-1
BRC-30, "
Description"C1102 RR LH SENSOR-1
C1103 FR RH SENSOR-1
C1104 FR LH SENSOR-1
C1105 RR RH SENSOR-2
BRC-33, "
Description"C1106 RR LH SENSOR-2
C1107 FR RH SENSOR-2
C1108 FR LH SENSOR-2
C1109 BATTERY VOLTAGE [ABNORMAL]BRC-36, "
Description"
C1110 CONTROLLER FAILUREBRC-38, "DTC Logic"
C 1111 P U M P M O T O RBRC-39, "Description"
C1113 G-SENSORXX-XX, "*****"
C1115 ABS SENSOR [ABNORMAL SIGNAL]BRC-41, "Description"
C1116 STOP LAMP SWBRC-44, "Description"
C1120 FR LH IN ABS SOLBRC-46, "Description"
C1121 FR LH OUT ABS SOLBRC-49, "Description"
C1122 FR RH IN ABS SOLBRC-46, "Description"
C1123 FR RH OUT ABS SOLBRC-49, "Description"
C1124 RR LH IN ABS SOLBRC-46, "Description"
C1125 RR LH OUT ABS SOLBRC-49, "Description"
C1126 RR RH IN ABS SOLBRC-46, "Description"
C1127 RR RH OUT ABS SOLBRC-49, "Description"
C1130 ENGINE SIGNAL 1
BRC-52, "
Description"
C1131 ENGINE SIGNAL 2
C1132 ENGINE SIGNAL 3
C1133 ENGINE SIGNAL 4
C1136 ENGINE SIGNAL 6
C1140 ACTUATOR RLYBRC-54, "
Description"
C1142 PRESS SEN CIRCUITXX-XX, "*****"
C1143 ST ANG SEN CIRCUIT
XX-XX, "*****"
C1144 ST ANG SEN SIGNAL

BRC-72
< ECU DIAGNOSIS >[ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
C1145 YAW RATE SENSOR
XX-XX, "*****"
C1146 SIDE G-SEN CIRCUIT
C1155 BR FLUID LEVEL LOWBRC-56, "
Description"
C1156 ST ANG SEN COM CIRXX-XX, "*****"
C1160 DECEL G SEN SETXX-XX, "*****"
C1163 ST ANGL SEN SAFEXX-XX, "*****"
C1164 CV1
XX-XX, "*****"
C1165 CV2
C1166 SV1
C1167 SV2
C1170 VARIANT CORDINGBRC-38, "
DTC Logic"
C1178 ABS ACTIVE BOOSTER SV NGXX-XX, "*****"
C1179 ABS DELTA S SEN NGXX-XX, "*****"
C1181 ABS ACTIVE BOOSTER RESPONSE NG
XX-XX, "*****"
C1184 ABS BRAKE RELEASE SW NG
C1189 ABS BRAKE BOOSTER DEFECT
U1000 CAN COMM CIRCUITBRC-59, "
Description"
DTC Items (CONSULT screen terms) Reference