fuel NISSAN TIIDA 2007 Service Owner's Manual

BCM (BODY CONTROL MODULE)
DLK-565
< ECU DIAGNOSIS >[WITHOUT I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
TURN SIGNAL LAMP CONTROL
BCM detects the turn signal lamp circuit status from the terminal voltage.
BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal
lamp operating.
NOTE:
The blinking speed is normal while activating the hazard warning lamp.
DTC Inspection Priority ChartINFOID:0000000001397105
DTC IndexINFOID:0000000001397106
NOTE:
Details of time display
 CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni-
tion switch OFF → ON again.
 PAST: Displays when there is a malfunction that is detected in the past and stored.
 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condition if the malfunction is detected again.
Display contents of CONSULT Fail-safe Cancellation
B2190: NATS ANTENNA AMP Inhibits engine cranking
Fuel cut (ECM)Erase DTC
B2191: DIFFERENCE OF KEY Inhibits engine cranking
Fuel cut (ECM)Erase DTC
B2192: ID DISCORD BCM-ECM Fuel cut (ECM) Erase DTC
B2193: CHAIN OF BCM-ECM Fuel cut (ECM) Erase DTC
B2194: DISCORD BCM-I-KEY Inhibits engine cranking
Fuel cut (ECM)Erase DTC
B2195: ANTI SCANNING Inhibits engine cranking
Fuel cut (ECM)Erase DTC
B2196: DONGLE NG Inhibits engine cranking
Fuel cut (ECM)Erase DTC
Priority DTC
1 U1000: CAN COMM CIRCUIT
 U1010: CONTROL UNIT (CAN)
2 B2190: NATS ANTENNA AMP
 B2191: DIFFERNCE OF KEY
 B2192: ID DISCORD BCM-ECM
 B2193: CHAIN OF BCM-ECM
 B2194: DISCORD BCM-I-KEY
 B2195: ANTI SCANNING
 B2196: DONGLE NG
CONSULT display TIME Fail-safe Refer to
No DTC is detected.
further testing
may be required.—— — —
U1000: CAN COMM CIRCUIT 0 1 - 39 —XX-XX, "*****"
U1010: CONTROL UNIT (CAN) 0 1 - 39 —XX-XX, "*****"
B2190: NATS ANTENNA AMP CRNT PAST×XX-XX, "*****"
B2191: DIFFERENCE OF KEY CRNT PAST×XX-XX, "*****"
B2192: ID DISCORD BCM-ECM CRNT PAST×XX-XX, "*****"

DLK-598
< REMOVAL AND INSTALLATION >[WITHOUT I-KEY & SUPER LOCK]
FUEL FILLER LID OPENER
FUEL FILLER LID OPENER
Removal and Installation of Fuel Filler Lid OpenerINFOID:0000000001732043
REMOVAL
1. Remove trunk side finisher (RH). Refer to XX-XX, "*****".
2. Remove fuel filler lid opener cable lock ring.
3. Remove front and rear kicking plates. Refer to XX-XX, "*****"
.
4. Remove rear cushion assembly. Refer to XX-XX, "*****"
.
5. Remove the bolts and the fuel filler lid opener handle.
6. Remove fuel filler lid opener cable clips from the vehicle.
7. Remove the fuel filler lid opener cable (LH drive).
8. Remove the fuel filler lid opener cable (RH drive).
PIIB3831J
LIIA2670E
LIIA2629E
ALKIA0651GB

FUEL FILLER LID OPENER
DLK-599
< REMOVAL AND INSTALLATION >[WITHOUT I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
INSTALLATION
Installation is in the reverse order of removal.

DLK-716
< ECU DIAGNOSIS >[WITHOUT I-KEY, WITH SUPER LOCK]
BCM (BODY CONTROL MODULE)
TURN SIGNAL LAMP CONTROL
BCM detects the turn signal lamp circuit status from the terminal voltage.
BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal
lamp operating.
NOTE:
The blinking speed is normal while activating the hazard warning lamp.
DTC Inspection Priority ChartINFOID:0000000001397330
DTC IndexINFOID:0000000001397331
NOTE:
Details of time display
 CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni-
tion switch OFF → ON again.
 PAST: Displays when there is a malfunction that is detected in the past and stored.
 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condition if the malfunction is detected again.
Display contents of CONSULT Fail-safe Cancellation
B2190: NATS ANTENNA AMP Inhibits engine cranking
Fuel cut (ECM)Erase DTC
B2191: DIFFERENCE OF KEY Inhibits engine cranking
Fuel cut (ECM)Erase DTC
B2192: ID DISCORD BCM-ECM Fuel cut (ECM) Erase DTC
B2193: CHAIN OF BCM-ECM Fuel cut (ECM) Erase DTC
B2194: DISCORD BCM-I-KEY Inhibits engine cranking
Fuel cut (ECM)Erase DTC
B2195: ANTI SCANNING Inhibits engine cranking
Fuel cut (ECM)Erase DTC
B2196: DONGLE NG Inhibits engine cranking
Fuel cut (ECM)Erase DTC
Priority DTC
1 U1000: CAN COMM CIRCUIT
 U1010: CONTROL UNIT (CAN)
2 B2190: NATS ANTENNA AMP
 B2191: DIFFERNCE OF KEY
 B2192: ID DISCORD BCM-ECM
 B2193: CHAIN OF BCM-ECM
 B2194: DISCORD BCM-I-KEY
 B2195: ANTI SCANNING
 B2196: DONGLE NG
CONSULT display TIME Fail-safe Refer to
No DTC is detected.
further testing
may be required.—— — —
U1000: CAN COMM CIRCUIT 0 1 - 39 —XX-XX, "*****"
U1010: CONTROL UNIT (CAN) 0 1 - 39 —XX-XX, "*****"
B2190: NATS ANTENNA AMP CRNT PAST×XX-XX, "*****"
B2191: DIFFERENCE OF KEY CRNT PAST×XX-XX, "*****"
B2192: ID DISCORD BCM-ECM CRNT PAST×XX-XX, "*****"

FUEL FILLER LID OPENER
DLK-749
< REMOVAL AND INSTALLATION >[WITHOUT I-KEY, WITH SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
FUEL FILLER LID OPENER
Removal and Installation of Fuel Filler Lid OpenerINFOID:0000000001732061
REMOVAL
1. Remove trunk side finisher (RH). Refer to XX-XX, "*****".
2. Remove fuel filler lid opener cable lock ring.
3. Remove front and rear kicking plates. Refer to XX-XX, "*****"
.
4. Remove rear cushion assembly. Refer to XX-XX, "*****"
.
5. Remove the bolts and the fuel filler lid opener handle.
6. Remove fuel filler lid opener cable clips from the vehicle.
7. Remove the fuel filler lid opener cable (LH drive).
8. Remove the fuel filler lid opener cable (RH drive).
PIIB3831J
LIIA2670E
LIIA2629E
ALKIA0651GB

DLK-750
< REMOVAL AND INSTALLATION >[WITHOUT I-KEY, WITH SUPER LOCK]
FUEL FILLER LID OPENER
INSTALLATION
Installation is in the reverse order of removal.

EC-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION EC
A
EC
N
O
P
CONTENTS
ENGINE CONTROL SYSTEM
HR16DE (WITH EURO-OBD)
BASIC INSPECTION ...................................
18
DIAGNOSIS AND REPAIR WORKFLOW .........18
Work Flow ...............................................................18
Diagnostic Work Sheet ............................................20
INSPECTION AND ADJUSTMENT ....................22
BASIC INSPECTION .................................................22
BASIC INSPECTION : Special Repair Require-
ment ........................................................................
22
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT ........................................................
25
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description ................................
25
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement .....
25
IDLE SPEED ..............................................................25
IDLE SPEED : Description ......................................26
IDLE SPEED : Special Repair Requirement ...........26
IGNITION TIMING ......................................................26
IGNITION TIMING : Description ..............................26
IGNITION TIMING : Special Repair Requirement ....26
ACCELERATOR PEDAL RELEASED POSITION
LEARNING ................................................................
26
ACCELERATOR PEDAL RELEASED POSITION
LEARNING : Description .........................................
26
ACCELERATOR PEDAL RELEASED POSITION
LEARNING : Special Repair Requirement ..............
26
THROTTLE VALVE CLOSED POSITION LEARN-
ING .............................................................................
27
THROTTLE VALVE CLOSED POSITION
LEARNING : Description .........................................
27
THROTTLE VALVE CLOSED POSITION
LEARNING : Special Repair Requirement ..............
27
IDLE AIR VOLUME LEARNING ................................27
IDLE AIR VOLUME LEARNING : Description .........27
IDLE AIR VOLUME LEARNING : Special Repair
Requirement ............................................................
27
MIXTURE RATIO SELF-LEARNING VALUE
CLEAR .......................................................................
29
MIXTURE RATIO SELF-LEARNING VALUE
CLEAR : Description ................................................
29
MIXTURE RATIO SELF-LEARNING VALUE
CLEAR : Special Repair Requirement .....................
29
FUNCTION DIAGNOSIS ..............................30
ENGINE CONTROL SYSTEM ..........................30
System Diagram .....................................................30
System Description ..................................................31
Component Parts Location ....................................31
Component Description ...........................................36
MULTIPORT FUEL INJECTION SYSTEM .......38
System Diagram .....................................................38
System Description ..................................................38
Component Parts Location ....................................41
Component Description ...........................................46
ELECTRIC IGNITION SYSTEM ........................47
System Diagram .....................................................47
System Description ..................................................47
Component Parts Location ....................................48
Component Description ...........................................53
AIR CONDITIONING CUT CONTROL ..............54
System Diagram ......................................................54
System Description ..................................................54
Component Parts Location ....................................55
Component Description ...........................................60
AUTOMATIC SPEED CONTROL DEVICE
(ASCD) ..............................................................
61
System Diagram ......................................................61
System Description ..................................................61

EC-3
C
D
E
F
G
H
I
J
K
L
M
ECA
N
O
P
P0171 FUEL INJECTION SYSTEM FUNC-
TION .................................................................
179
DTC Logic .............................................................179
Diagnosis Procedure .............................................180
P0172 FUEL INJECTION SYSTEM FUNC-
TION .................................................................
183
DTC Logic .............................................................183
Diagnosis Procedure .............................................184
P0222, P0223 TP SENSOR .............................187
Description ............................................................187
DTC Logic .............................................................187
Diagnosis Procedure .............................................187
Component Inspection ..........................................189
Special Repair Requirement .................................189
P0300, P0301, P0302, P0303, P0304 MIS-
FIRE ..................................................................
190
DTC Logic .............................................................190
Diagnosis Procedure .............................................191
P0327, P0328 KS .............................................195
Description ............................................................195
DTC Logic .............................................................195
Diagnosis Procedure .............................................195
Component Inspection ..........................................196
P0335 CKP SENSOR (POS) ............................197
Description ............................................................197
DTC Logic .............................................................197
Diagnosis Procedure .............................................198
Component Inspection ..........................................200
P0340 CMP SENSOR (PHASE) .......................201
Description ............................................................201
DTC Logic .............................................................201
Diagnosis Procedure .............................................202
Component Inspection ..........................................203
P0420 THREE WAY CATALYST FUNCTION ..205
DTC Logic .............................................................205
Component Function Check ..................................206
Diagnosis Procedure .............................................207
P0444 EVAP CANISTER PURGE VOLUME
CONTROL SOLENOID VALVE .......................
210
Description ............................................................210
DTC Logic .............................................................210
Diagnosis Procedure .............................................210
Component Inspection ..........................................211
P0500 VSS .......................................................213
Description ............................................................213
DTC Logic .............................................................213
Component Function Check ..................................214
Diagnosis Procedure .............................................214
P0605 ECM .......................................................215
Description ............................................................215
DTC Logic .............................................................215
Diagnosis Procedure .............................................216
P1065 ECM .....................................................217
Description .............................................................217
DTC Logic ..............................................................217
Diagnosis Procedure .............................................217
P1111 IVT CONTROL SOLENOID VALVE ....219
Description .............................................................219
DTC Logic ..............................................................219
Diagnosis Procedure .............................................219
Component Inspection ...........................................220
P1121 ELECTRIC THROTTLE CONTROL
ACTUATOR .....................................................
222
Description .............................................................222
DTC Logic ..............................................................222
Diagnosis Procedure .............................................222
Special Repair Requirement ..................................223
P1122 ELECTRIC THROTTLE CONTROL
FUNCTION ......................................................
224
Description .............................................................224
DTC Logic ..............................................................224
Diagnosis Procedure .............................................224
Component Inspection ...........................................227
Special Repair Requirement ..................................227
P1124, P1126 THROTTLE CONTROL MO-
TOR RELAY ....................................................
228
Description .............................................................228
DTC Logic ..............................................................228
Diagnosis Procedure .............................................228
P1128 THROTTLE CONTROL MOTOR .........231
Description .............................................................231
DTC Logic ..............................................................231
Diagnosis Procedure .............................................231
Component Inspection ...........................................232
Special Repair Requirement ..................................232
P1143 HO2S1 ..................................................233
Description .............................................................233
DTC Logic ..............................................................233
Diagnosis Procedure .............................................234
Component Inspection ...........................................235
P1144 HO2S1 ..................................................238
Description .............................................................238
DTC Logic ..............................................................238
Diagnosis Procedure .............................................239
Component Inspection ...........................................240
P1146 HO2S2 ..................................................243
Description .............................................................243
DTC Logic ..............................................................243
Component Function Check ..................................245
Diagnosis Procedure .............................................246
Component Inspection ...........................................247
P1147 HO2S2 ..................................................250

EC-4
Description .............................................................250
DTC Logic ..............................................................250
Component Function Check ..................................252
Diagnosis Procedure .............................................253
Component Inspection ...........................................254
P1212 TCS COMMUNICATION LINE .............256
Description .............................................................256
DTC Logic ..............................................................256
Diagnosis Procedure .............................................256
P1217 ENGINE OVER TEMPERATURE .........257
DTC Logic ..............................................................257
Component Function Check ..................................257
Diagnosis Procedure .............................................258
P1225 TP SENSOR .........................................261
Description .............................................................261
DTC Logic ..............................................................261
Diagnosis Procedure .............................................261
Special Repair Requirement ..................................262
P1226 TP SENSOR .........................................263
Description .............................................................263
DTC Logic ..............................................................263
Diagnosis Procedure .............................................263
Special Repair Requirement ..................................264
P1229 SENSOR POWER SUPPLY .................265
DTC Logic ..............................................................265
Diagnosis Procedure .............................................265
P1564 ASCD STEERING SWITCH .................267
Description .............................................................267
DTC Logic ..............................................................267
Diagnosis Procedure .............................................267
Component Inspection ...........................................269
P1572 ASCD BRAKE SWITCH .......................270
Description .............................................................270
DTC Logic ..............................................................270
Diagnosis Procedure .............................................271
Component Inspection (ASCD Brake Switch) .......275
Component Inspection (ASCD Clutch Switch) .......276
Component Inspection (Stop Lamp Switch) ..........276
P1574 ASCD VEHICLE SPEED SENSOR ......278
Description .............................................................278
DTC Logic ..............................................................278
Diagnosis Procedure .............................................278
P1706 PNP SWITCH .......................................280
Description .............................................................280
DTC Logic ..............................................................280
Component Function Check ..................................281
Diagnosis Procedure .............................................281
P1805 BRAKE SWITCH ..................................283
Description .............................................................283
DTC Logic ..............................................................283
Diagnosis Procedure .............................................283
Component Inspection (Stop Lamp Switch) ..........284
P2122, P2123 APP SENSOR ...........................286
Description ............................................................286
DTC Logic .............................................................286
Diagnosis Procedure .............................................286
Component Inspection ..........................................288
Special Repair Requirement .................................288
P2127, P2128 APP SENSOR ...........................290
Description ............................................................290
DTC Logic .............................................................290
Diagnosis Procedure .............................................290
Component Inspection ..........................................293
Special Repair Requirement .................................293
P2135 TP SENSOR ..........................................294
Description ............................................................294
DTC Logic .............................................................294
Diagnosis Procedure .............................................294
Component Inspection ..........................................296
Special Repair Requirement .................................296
P2138 APP SENSOR .......................................297
Description ............................................................297
DTC Logic .............................................................297
Diagnosis Procedure .............................................297
Component Inspection ..........................................300
Special Repair Requirement .................................300
ASCD BRAKE SWITCH ...................................302
Description ............................................................302
Component Function Check .................................302
Diagnosis Procedure .............................................302
Component Inspection (ASCD Brake Switch) .......305
Component Inspection (ASCD Clutch Switch) ......305
ASCD INDICATOR ...........................................306
Description ............................................................306
Component Function Check .................................306
Diagnosis Procedure .............................................306
COOLING FAN .................................................307
Description ............................................................307
Component Function Check .................................307
Diagnosis Procedure .............................................307
Component Inspection ..........................................309
ELECTRICAL LOAD SIGNAL ..........................311
Description ............................................................311
Component Function Check .................................311
Diagnosis Procedure .............................................311
FUEL INJECTOR ..............................................313
Description ............................................................313
Component Function Check .................................313
Diagnosis Procedure .............................................313
Component Inspection ..........................................314
FUEL PUMP .....................................................316
Description ............................................................316

EC-5
C
D
E
F
G
H
I
J
K
L
M
ECA
N
O
P Component Function Check ..................................
316
Diagnosis Procedure .............................................316
Component Inspection (Fuel Pump) .....................318
IGNITION SIGNAL ...........................................319
Description ............................................................319
Component Function Check ..................................319
Diagnosis Procedure .............................................319
Component Inspection (Ignition Coil with Power
Transistor) .............................................................
322
Component Inspection (Condenser) .....................322
MALFUNCTION INDICATOR ...........................324
Description ............................................................324
Component Function Check ..................................324
Diagnosis Procedure .............................................324
POSITIVE CRANKCASE VENTILATION ........325
Description ............................................................325
Component Inspection ..........................................325
REFRIGERANT PRESSURE SENSOR ...........326
Description ............................................................326
Component Function Check ..................................326
Diagnosis Procedure .............................................326
ECU DIAGNOSIS .......................................328
ECM ..................................................................328
Reference Value ...................................................328
Wiring Diagram - ENGINE CONTROL SYSTEM - ..339
Fail Safe ...............................................................358
DTC Inspection Priority Chart .............................360
DTC Index ............................................................361
How to Set SRT Code ........................................363
Test Value and Test Limit ..................................365
SYMPTOM DIAGNOSIS ............................366
ENGINE CONTROL SYSTEM SYMPTOMS ....366
Symptom Table .....................................................366
NORMAL OPERATING CONDITION ...............370
Description ............................................................370
PRECAUTION ............................................371
PRECAUTIONS ................................................371
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................
371
Precaution for Procedure without Cowl Top Cover ..371
Precautions For Xenon Headlamp Service ...........371
On Board Diagnostic (OBD) System of Engine
and A/T ..................................................................
372
General Precautions .............................................372
PREPARATION .........................................375
PREPARATION ................................................375
Special Service Tools ............................................375
Commercial Service Tools ....................................375
ON-VEHICLE MAINTENANCE ..................377
FUEL PRESSURE ...........................................377
Inspection ..............................................................377
EVAPORATIVE EMISSION SYSTEM .............379
Inspection ..............................................................379
SERVICE DATA AND SPECIFICATIONS
(SDS) ..........................................................
380
SERVICE DATA AND SPECIFICATIONS
(SDS) ...............................................................
380
Idle Speed .............................................................380
Ignition Timing .......................................................380
Calculated Load Value ..........................................380
Mass Air Flow Sensor ............................................380
HR16DE (WITHOUT EURO-OBD)
BASIC INSPECTION .................................
381
DIAGNOSIS AND REPAIR WORKFLOW ......381
Work Flow ..............................................................381
Diagnostic Work Sheet ..........................................383
INSPECTION AND ADJUSTMENT ................385
BASIC INSPECTION ...............................................385
BASIC INSPECTION : Special Repair Require-
ment .......................................................................
385
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT ......................................................
388
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description ...............................
388
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement ....
388
IDLE SPEED ............................................................388
IDLE SPEED : Description ....................................389
IDLE SPEED : Special Repair Requirement .........389
IGNITION TIMING ....................................................389
IGNITION TIMING : Description ............................389
IGNITION TIMING : Special Repair Requirement ..389
ACCELERATOR PEDAL RELEASED POSITION
LEARNING ...............................................................
389
ACCELERATOR PEDAL RELEASED POSITION
LEARNING : Description .......................................
389
ACCELERATOR PEDAL RELEASED POSITION
LEARNING : Special Repair Requirement ............
389
THROTTLE VALVE CLOSED POSITION LEARN-
ING ...........................................................................
390
THROTTLE VALVE CLOSED POSITION
LEARNING : Description .......................................
390
THROTTLE VALVE CLOSED POSITION
LEARNING : Special Repair Requirement ............
390
IDLE AIR VOLUME LEARNING ..............................390
IDLE AIR VOLUME LEARNING : Description .......390