warning NISSAN TIIDA 2007 Service Owner's Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2007, Model line: TIIDA, Model: NISSAN TIIDA 2007Pages: 5883, PDF Size: 78.95 MB
Page 229 of 5883
REAR DISC BRAKE
BR-37
< DISASSEMBLY AND ASSEMBLY >
C
D
E
G
H
I
J
K
L
MA
B
BR
N
O
P
REAR DISC BRAKE
Disassembly and AssemblyINFOID:0000000001724669
DISASSEMBLY
1. Remove the sliding pin bolt, and then remove the pad, shim, shim cover, and pad retainer from the torque
member and cylinder.
2. Remove sliding pin boot from torque member.
3. Remove the retaining ring from the cylinder body using a screw-
driver or suitable tool, as shown.
4. Place a wooden block as shown, and blow air from connecting
bolt mounting hole to remove pistons and piston boots.
WARNING:
Do not place your finger in front of piston.
5. Remove piston seals from cylinder body using a screwdriver or
suitable tool, as shown.
CAUTION:
Be careful not to damage cylinder inner wall.
CALIPER INSPECTION
Cylinder Body
CAUTION:
Use new brake fluid to clean. Never use mineral oils such as gasoline or kerosene.
Check inner wall of cylinder for corrosion, wear, and damage. If any non-standard condition is
detected, replace cylinder body.
Minor flaws caused by corrosion or a foreign material can be removed by polishing the surface with
a fine sandpaper. Replace the cylinder body, if necessary.
Torque Member
Check for wear, cracks, and damage. If damage or deformation is present, replace the affected part.
Piston
CAUTION:
SBR028A
BRD0041D
PFIA0269E
Page 235 of 5883
BRC-2
C1110, C1170 ABS ACTUATOR AND ELEC-
TRIC UNIT (CONTROL UNIT) ...........................
38
DTC Logic ...............................................................38
Diagnosis Procedure ..............................................38
Special Repair Requirement ...................................38
C1111 ABS MOTOR, MOTOR RELAY SYS-
TEM ....................................................................
39
Description ..............................................................39
DTC Logic ...............................................................39
Diagnosis Procedure ..............................................39
Component Inspection ............................................40
Special Repair Requirement ...................................40
C1115 WHEEL SENSOR ...................................41
Description ..............................................................41
DTC Logic ...............................................................41
Diagnosis Procedure ..............................................41
Component Inspection ............................................42
Special Repair Requirement ...................................43
C1116 STOP LAMP SWITCH ............................44
Description ..............................................................44
DTC Logic ...............................................................44
Diagnosis Procedure ..............................................44
Special Repair Requirement ...................................45
C1120, C1122, C1124, C1126 IN ABS SOL .....46
Description ..............................................................46
DTC Logic ...............................................................46
Diagnosis Procedure ..............................................46
Component Inspection ............................................47
Special Repair Requirement ...................................48
C1121, C1123, C1125, C1127 OUT ABS SOL ...49
Description ..............................................................49
DTC Logic ...............................................................49
Diagnosis Procedure ..............................................49
Component Inspection ............................................50
Special Repair Requirement ...................................51
C1130, C1131, C1132, C1133, C1136 EN-
GINE SIGNAL ....................................................
52
Description ..............................................................52
DTC Logic ...............................................................52
Diagnosis Procedure ..............................................52
Special Repair Requirement ...................................52
C1140 ACTUATOR RLY ...................................54
Description ..............................................................54
DTC Logic ...............................................................54
Diagnosis Procedure ..............................................54
Component Inspection ............................................55
Special Repair Requirement ...................................55
C1155 BRAKE FLUID LEVEL SWITCH ............56
Description ..............................................................56
DTC Logic ...............................................................56
Diagnosis Procedure ..............................................56
Component Inspection ............................................57
Special Repair Requirement ...................................57
U1000 CAN COMM CIRCUIT ............................59
Description ..............................................................59
DTC Logic ...............................................................59
Diagnosis Procedure ...............................................59
Special Repair Requirement ...................................59
ABS WARNING LAMP ......................................60
Description ..............................................................60
Component Function Check ...................................60
Diagnosis Procedure ...............................................60
BRAKE WARNING LAMP .................................61
Description ..............................................................61
Component Function Check ...................................61
Diagnosis Procedure ...............................................61
ECU DIAGNOSIS .......................................62
ABS ACTUATOR AND ELECTRIC UNIT
(CONTROL UNIT) ..............................................
62
Reference Value .....................................................62
Wiring Diagram - LHD .............................................67
Wiring Diagram - RHD ............................................69
Fail-Safe ..................................................................70
DTC No. Index ........................................................71
SYMPTOM DIAGNOSIS ............................73
ABS ....................................................................73
Symptom Table .......................................................73
EXCESSIVE ABS FUNCTION OPERATION
FREQUENCY .....................................................
74
Diagnosis Procedure ...............................................74
UNEXPECTED PEDAL REACTION ..................75
Diagnosis Procedure ...............................................75
THE BRAKING DISTANCE IS LONG ...............76
Diagnosis Procedure ...............................................76
ABS FUNCTION DOES NOT OPERATE ..........77
Diagnosis Procedure ...............................................77
PEDAL VIBRATION OR ABS OPERATION
SOUND OCCURS ..............................................
78
Diagnosis Procedure ...............................................78
NORMAL OPERATING CONDITION ................79
Description ..............................................................79
PRECAUTION ............................................80
PRECAUTIONS .................................................80
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .................................................................
80
Precaution for Brake System ..................................80
Precaution for Brake Control ...................................80
Precaution for Harness Repair ................................81
Page 237 of 5883
BRC-4
C1115 WHEEL SENSOR .................................124
Description .............................................................124
DTC Logic ..............................................................124
Diagnosis Procedure .............................................124
Component Inspection ...........................................125
Special Repair Requirement ..................................126
C1116 STOP LAMP SWITCH ..........................127
Description .............................................................127
DTC Logic ..............................................................127
Diagnosis Procedure .............................................127
Special Repair Requirement ..................................128
C1120, C1122, C1124, C1126 IN ABS SOL ...129
Description .............................................................129
DTC Logic ..............................................................129
Diagnosis Procedure .............................................129
Component Inspection ...........................................130
Special Repair Requirement ..................................131
C1121, C1123, C1125, C1127 OUT ABS SOL .132
Description .............................................................132
DTC Logic ..............................................................132
Diagnosis Procedure .............................................132
Component Inspection ...........................................133
Special Repair Requirement ..................................134
C1130, C1131, C1132, C1133, C1136 EN-
GINE SIGNAL ..................................................
135
Description .............................................................135
DTC Logic ..............................................................135
Diagnosis Procedure .............................................135
Special Repair Requirement ..................................135
C1140 ACTUATOR RLY .................................137
Description .............................................................137
DTC Logic ..............................................................137
Diagnosis Procedure .............................................137
Component Inspection ...........................................138
Special Repair Requirement ..................................138
C1142 PRESS SENSOR .................................139
Description .............................................................139
DTC Logic ..............................................................139
Diagnosis Procedure .............................................139
Component Inspection ...........................................141
Special Repair Requirement ..................................141
C1143, C1144 STEERING ANGLE SENSOR .142
Description .............................................................142
DTC Logic ..............................................................142
Diagnosis Procedure .............................................142
Component Inspection ...........................................143
Special Repair Requirement ..................................143
C1155 BRAKE FLUID LEVEL SWITCH ..........145
Description .............................................................145
DTC Logic ..............................................................145
Diagnosis Procedure .............................................145
Component Inspection ...........................................146
Special Repair Requirement ..................................146
C1156 ST ANG SEN COM CIR ........................148
Description ............................................................148
DTC Logic .............................................................148
Diagnosis Procedure .............................................148
C1160 DECEL G SEN SET ..............................149
Description ............................................................149
DTC Logic .............................................................149
Diagnosis Procedure .............................................149
C1163 ST ANGLE SEN SAFE .........................150
Description ............................................................150
DTC Logic .............................................................150
Diagnosis Procedure .............................................150
C1179 ABS DELTA S SEN NG ........................151
Description ............................................................151
DTC Logic .............................................................151
Diagnosis Procedure .............................................151
Component Inspection ..........................................152
Special Repair Requirement .................................152
U1000 CAN COMM CIRCUIT ...........................153
Description ............................................................153
DTC Logic .............................................................153
Diagnosis Procedure .............................................153
Special Repair Requirement .................................153
VDC OFF SWITCH ...........................................154
Description ............................................................154
Component Function Check .................................154
Diagnosis Procedure .............................................154
Component Inspection ..........................................155
ABS WARNING LAMP .....................................156
Description ............................................................156
Component Function Check .................................156
Diagnosis Procedure .............................................156
BRAKE WARNING LAMP ................................157
Description ............................................................157
Component Function Check .................................157
Diagnosis Procedure .............................................157
VDC OFF INDICATOR LAMP ..........................158
Description ............................................................158
Component Function Check .................................158
Diagnosis Procedure .............................................158
SLIP INDICATOR LAMP ..................................159
Description ............................................................159
Component Function Check .................................159
Diagnosis Procedure .............................................159
ECU DIAGNOSIS ......................................160
ABS ACTUATOR AND ELECTRIC UNIT
(CONTROL UNIT) .............................................
160
Reference Value ...................................................160
Wiring Diagram - LHD ...........................................165
Wiring Diagram - RHD ..........................................167
Page 241 of 5883
![NISSAN TIIDA 2007 Service Owners Manual BRC-8
< BASIC INSPECTION >[ABS]
DIAGNOSIS AND REPAIR WORKFLOW
2.PERFORM THE SELF-DIAGNOSIS
Check the DTC display with the self-diagnosis function. Refer to BRC-25, "
CONSULT-III Function (ABS)".
Is th](/img/5/57395/w960_57395-240.png "NISSAN TIIDA 2007 Service Owners Manual BRC-8
< BASIC INSPECTION >[ABS]
DIAGNOSIS AND REPAIR WORKFLOW
2.PERFORM THE SELF-DIAGNOSIS
Check the DTC display with the self-diagnosis function. Refer to BRC-25, \"
CONSULT-III Function (ABS)\".
Is th")
BRC-8
< BASIC INSPECTION >[ABS]
DIAGNOSIS AND REPAIR WORKFLOW
2.PERFORM THE SELF-DIAGNOSIS
Check the DTC display with the self-diagnosis function. Refer to BRC-25, "
CONSULT-III Function (ABS)".
Is there any DTC displayed?
YES >> GO TO 3
NO >> GO TO 4
3.PERFORM THE SYSTEM DIAGNOSIS
Perform the diagnosis applicable to the displayed DTC. Refer to BRC-71, "
DTC No. Index".
>> GO TO 7
4.CHECK THE SYMPTOM THAT IS NOT CONSIDERED A SYSTEM MALFUNCTION
Check that the symptom is a normal operation that is not considered a system malfunction. Refer to BRC-79,
"Description".
Is the symptom a normal operation?
YES >> INSPECTION END
NO >> GO TO 5
5.CHECK THE WARNING LAMP AND INDICATOR LAMP FOR ILLUMINATION
Check that the warning lamp and indicator lamp illuminate.
• ABS warning lamp: Refer to BRC-60, "
Description".
Brake warning lamp: Refer to BRC-61, "
Description".
VDC OFF indicator lamp: Refer to XX-XX, "*****"
.
SLIP indicator lamp: Refer to XX-XX, "*****"
.
Is ON/OFF timing normal?
YES >> GO TO 6
NO >> GO TO 2
6.PERFORM THE DIAGNOSIS BY SYMPTOM
Perform the diagnosis applicable to the symptom.
>> GO TO 7
7.REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the specified malfunctioning parts.
>> GO TO 8
8.FINAL CHECK
Perform the self-diagnosis again, and check that the malfunction is repaired completely. After checking, erase
the self-diagnosis memory. Refer to BRC-25, "
CONSULT-III Function (ABS)".
Is no other DTC present and the repair completed?
YES >> INSPECTION END
NO >> GO TO 3
Page 248 of 5883
![NISSAN TIIDA 2007 Service Owners Manual VDC
BRC-15
< FUNCTION DIAGNOSIS >[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
Component DescriptionINFOID:0000000001731211
1. Front wheel sensor
LH E18
RH E1172. ABS actuator and electric unit (con-
trol un](/img/5/57395/w960_57395-247.png "NISSAN TIIDA 2007 Service Owners Manual VDC
BRC-15
< FUNCTION DIAGNOSIS >[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
Component DescriptionINFOID:0000000001731211
1. Front wheel sensor
LH E18
RH E1172. ABS actuator and electric unit (con-
trol un")
VDC
BRC-15
< FUNCTION DIAGNOSIS >[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
Component DescriptionINFOID:0000000001731211
1. Front wheel sensor
LH E18
RH E1172. ABS actuator and electric unit (con-
trol unit) E1253. Combination meter M24
4. Rear wheel sensor
LH C11
RH C105. Yaw rate/side/decel G sensor M108 6. Steering angle sensor M17 (view
with steering wheel removed)
7. VDC OFF switch M257 8. Active booster E49 9. Delta stroke sensor E114
10. Brake fluid level switch E21 11. Front pressure sensor E31 12. Rear pressure sensor E32
Component parts Reference
ABS actuator and electric unit (control unit)Pump
BRC-39, "
Description"Motor
Actuator relayBRC-54, "
Description"
Solenoid valveBRC-46, "Description"
VDC switch-over valve
(CV1, CV2, SV1, SV2)XX-XX, "*****"
Wheel sensorBRC-30, "Description"
Yaw rate/side/decel G sensorXX-XX, "*****"
Steering angle sensorXX-XX, "*****"
VDC OFF switchXX-XX, "*****"
ABS warning lampBRC-60, "Description"
Brake warning lampBRC-61, "Description"
VDC OFF indicator lampXX-XX, "*****"
SLIP indicator lampXX-XX, "*****"
Front pressure sensor
XX-XX, "*****"
Rear pressure sensor
Active boosterXX-XX, "*****"
Delta stroke sensorXX-XX, "*****"
Page 251 of 5883
![NISSAN TIIDA 2007 Service Owners Manual BRC-18
< FUNCTION DIAGNOSIS >[ABS]
TCS
Component Description
INFOID:0000000001731215
1. Front wheel sensor
LH E18
RH E1172. ABS actuator and electric unit (con-
trol unit) E1253. Combination meter M24](/img/5/57395/w960_57395-250.png "NISSAN TIIDA 2007 Service Owners Manual BRC-18
< FUNCTION DIAGNOSIS >[ABS]
TCS
Component Description
INFOID:0000000001731215
1. Front wheel sensor
LH E18
RH E1172. ABS actuator and electric unit (con-
trol unit) E1253. Combination meter M24")
BRC-18
< FUNCTION DIAGNOSIS >[ABS]
TCS
Component Description
INFOID:0000000001731215
1. Front wheel sensor
LH E18
RH E1172. ABS actuator and electric unit (con-
trol unit) E1253. Combination meter M24
4. Rear wheel sensor
LH C11
RH C105. Yaw rate/side/decel G sensor M108 6. Steering angle sensor M17 (view
with steering wheel removed)
7. VDC OFF switch M257 8. Active booster E49 9. Delta stroke sensor E114
10. Brake fluid level switch E21 11. Front pressure sensor E31 12. Rear pressure sensor E32
Component parts Reference
ABS actuator and electric unit (control unit)Pump
BRC-39, "
Description"Motor
Actuator relayBRC-54, "
Description"
Solenoid valveBRC-46, "Description"
VDC switch-over valve
(CV1, CV2, SV1, SV2)XX-XX, "*****"
Wheel sensorBRC-30, "Description"
Yaw rate/side/decel G sensorXX-XX, "*****"
Steering angle sensorXX-XX, "*****"
VDC OFF switchXX-XX, "*****"
ABS warning lampBRC-60, "Description"
Brake warning lampBRC-61, "Description"
VDC OFF indicator lampXX-XX, "*****"
SLIP indicator lampXX-XX, "*****"
Front pressure sensor
XX-XX, "*****"
Rear pressure sensor
Active boosterXX-XX, "*****"
Delta stroke sensorXX-XX, "*****"
Page 254 of 5883
![NISSAN TIIDA 2007 Service Owners Manual ABS
BRC-21
< FUNCTION DIAGNOSIS >[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
Component DescriptionINFOID:0000000001731219
1. Front wheel sensor
LH E18
RH E1172. ABS actuator and electric unit (con-
trol un](/img/5/57395/w960_57395-253.png "NISSAN TIIDA 2007 Service Owners Manual ABS
BRC-21
< FUNCTION DIAGNOSIS >[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
Component DescriptionINFOID:0000000001731219
1. Front wheel sensor
LH E18
RH E1172. ABS actuator and electric unit (con-
trol un")
ABS
BRC-21
< FUNCTION DIAGNOSIS >[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
Component DescriptionINFOID:0000000001731219
1. Front wheel sensor
LH E18
RH E1172. ABS actuator and electric unit (con-
trol unit) E1253. Combination meter M24
4. Rear wheel sensor
LH C11
RH C105. Yaw rate/side/decel G sensor M108 6. Steering angle sensor M17 (view
with steering wheel removed)
7. VDC OFF switch M257 8. Active booster E49 9. Delta stroke sensor E114
10. Brake fluid level switch E21 11. Front pressure sensor E31 12. Rear pressure sensor E32
Component parts Reference
ABS actuator and electric unit (control unit)Pump
BRC-39, "
Description"Motor
Actuator relayBRC-54, "
Description"
Solenoid valveBRC-46, "Description"
Wheel sensorBRC-30, "Description"
ABS warning lampBRC-60, "Description"
Brake warning lampBRC-61, "Description"
Page 257 of 5883
![NISSAN TIIDA 2007 Service Owners Manual BRC-24
< FUNCTION DIAGNOSIS >[ABS]
EBD
Component Description
INFOID:0000000001731223
1. Front wheel sensor
LH E18
RH E1172. ABS actuator and electric unit (con-
trol unit) E1253. Combination meter M24](/img/5/57395/w960_57395-256.png "NISSAN TIIDA 2007 Service Owners Manual BRC-24
< FUNCTION DIAGNOSIS >[ABS]
EBD
Component Description
INFOID:0000000001731223
1. Front wheel sensor
LH E18
RH E1172. ABS actuator and electric unit (con-
trol unit) E1253. Combination meter M24")
BRC-24
< FUNCTION DIAGNOSIS >[ABS]
EBD
Component Description
INFOID:0000000001731223
1. Front wheel sensor
LH E18
RH E1172. ABS actuator and electric unit (con-
trol unit) E1253. Combination meter M24
4. Rear wheel sensor
LH C11
RH C105. Yaw rate/side/decel G sensor M108 6. Steering angle sensor M17 (view
with steering wheel removed)
7. VDC OFF switch M257 8. Active booster E49 9. Delta stroke sensor E114
10. Brake fluid level switch E21 11. Front pressure sensor E31 12. Rear pressure sensor E32
Component parts Reference
ABS actuator and electric unit (control unit)Pump
BRC-39, "
Description"Motor
Actuator relayBRC-54, "
Description"
Solenoid valveBRC-46, "Description"
Wheel sensorBRC-30, "Description"
ABS warning lampBRC-60, "Description"
Brake warning lampBRC-61, "Description"
Page 258 of 5883
![NISSAN TIIDA 2007 Service Owners Manual DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
BRC-25
< FUNCTION DIAGNOSIS >[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
C](/img/5/57395/w960_57395-257.png "NISSAN TIIDA 2007 Service Owners Manual DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
BRC-25
< FUNCTION DIAGNOSIS >[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
C")
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
BRC-25
< FUNCTION DIAGNOSIS >[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
CONSULT-III Function (ABS)INFOID:0000000001731224
FUNCTION
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
SELF-DIAG RESULTS MODE
Operation Procedure
1. Before performing the self-diagnosis, start engine and drive vehicle at 30 km/h (19 MPH) or more for
approximately 1 minute.
How to Erase Self-diagnosis Results
1. After erasing DTC memory, start engine and drive vehicle at 30 km/h (19 MPH) or more for approximately
1 minute as the final inspection, and make sure that the ABS warning lamp, VDC OFF indicator lamp,
SLIP indicator lamp and brake warning lamp turn OFF.
CAUTION:
If memory cannot be erased, perform applicable diagnosis.
NOTE:
When the wheel sensor malfunctions, after inspecting the wheel sensor system, the ABS warning lamp,
VDC OFF indicator lamp, SLIP indicator lamp and brake warning lamp will not turn OFF even when the
system is normal unless the vehicle is driving at approximately 30 km/h (19 MPH) or more for approxi-
mately 1 minute.
Brake warning lamp will turn ON in case of parking brake operation (when switch is ON) or of brake fluid
level switch operation (when brake fluid is insufficient).
VDC OFF switch should not stay “ON” position.
Display Item List
Refer to BRC-71, "DTC No. Index".
DATA MONITOR MODE
Display Item List
Diagnostic test mode Function
Work supportThis mode enables a technician to adjust some devices faster and more accurately by following
the indications on CONSULT-III.
Self-diagnostic results Self-diagnostic results can be read and erased quickly.
Data monitor Input/Output data in the ABS actuator and electric unit (control unit) can be read.
Active testDiagnostic test mode is which CONSULT-III drives some actuators apart from the ABS actuator
and electric unit (control unit) and also shifts some parameters in a specified range.
ECU part number ABS actuator and electric unit (control unit) part number can be read.
CAN diagnostic support monitor The results of transmit/receive diagnosis of CAN communication can be read.
Item
(Unit)Data monitor item selection
Remarks
ECU INPUT
SIGNALSMAIN
SIGNALSSELECTION
FROM MENU
GEAR×××Gear position judged by PNP switch
signal is displayed.
FR RH SENSOR
(km/h, MPH)×××Wheel speed calculated by front RH
wheel sensor signal is displayed.
FR LH SENSOR
(km/h, MPH)×××Wheel speed calculated by front LH
wheel sensor signal is displayed.
RR RH SENSOR
(km/h, MPH)×××Wheel speed calculated by rear RH
wheel sensor signal is displayed.
Page 259 of 5883
![NISSAN TIIDA 2007 Service Owners Manual BRC-26
< FUNCTION DIAGNOSIS >[ABS]
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
RR LH SENSOR
(km/h, MPH)×××Wheel speed calculated by rear LH
wheel sensor signal is displayed](/img/5/57395/w960_57395-258.png "NISSAN TIIDA 2007 Service Owners Manual BRC-26
< FUNCTION DIAGNOSIS >[ABS]
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
RR LH SENSOR
(km/h, MPH)×××Wheel speed calculated by rear LH
wheel sensor signal is displayed")
BRC-26
< FUNCTION DIAGNOSIS >[ABS]
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
RR LH SENSOR
(km/h, MPH)×××Wheel speed calculated by rear LH
wheel sensor signal is displayed.
BATTERY VOLT
(V)×××Voltage supplied to ABS actuator
and electric unit (control unit) is dis-
played.
N POSI SIG – –×Shift position judged by PNP switch
signal.
P POSI SIG – –×Shift position judged by PNP switch
signal.
ACCEL POS SIG
(%)×–×Throttle valve open/close status
judged by CAN communication sig-
nal is displayed.
ENGINE SPEED
(rpm)×××Engine speed judged by CAN com-
munication signal is displayed.
STR ANGLE SIG
(deg)×–×Steering angle detected by steering
angle sensor is displayed.
YAW RATE SEN
(d/s)×××Yaw rate detected by yaw rate sen-
sor is displayed.
SIDE G-SENSOR
(m/s
2)×– ×Transverse acceleration detected
by side G-sensor is displayed.
STOP LAMP SW
(ON/OFF)×××Stop lamp switch (ON/OFF) status
is displayed.
OFF SW
(ON/OFF) ×× ×VDC OFF switch (ON/OFF) status
is displayed.
ABS WARN LAMP
(ON/OFF)–××ABS warning lamp (ON/OFF) status
is displayed.
SLIP LAMP
(ON/OFF)–××SLIP indicator lamp (ON/OFF) sta-
tus is displayed.
FR LH IN SOL
(ON/OFF)–××Front LH IN ABS solenoid (ON/
OFF) status is displayed.
FR LH OUT SOL
(ON/OFF)–××Front LH OUT ABS solenoid (ON/
OFF) status is displayed.
RR RH IN SOL
(ON/OFF)–××Rear RH IN ABS solenoid (ON/
OFF) status is displayed.
RR RH OUT SOL
(ON/OFF) –××Rear RH OUT ABS solenoid (ON/
OFF) status is displayed.
FR RH IN SOL
(ON/OFF)–××Front RH IN ABS solenoid (ON/
OFF) status is displayed.
FR RH OUT SOL
(ON/OFF)–××Front RH OUT ABS solenoid (ON/
OFF) status is displayed.
RR LH IN SOL
(ON/OFF)–××Rear LH IN ABS solenoid (ON/OFF)
status is displayed.
RR LH OUT SOL
(ON/OFF)–××Rear LH OUT ABS solenoid (ON/
OFF) status is displayed.
OFF LAMP
(ON/OFF)–××OFF Lamp (ON/OFF) status is dis-
played.
MOTOR RELAY
(ON/OFF)–××ABS motor relay signal (ON/OFF)
status is displayed.
ACTUATOR RLY
(ON/OFF)– ××ABS actuator relay signal (ON/OFF)
status is displayed. Item
(Unit)Data monitor item selection
Remarks
ECU INPUT
SIGNALS
MAIN
SIGNALSSELECTION
FROM MENU