check oil NISSAN TIIDA 2007 Service Repair Manual

SIDE OIL SEAL
TM-673
< ON-VEHICLE REPAIR >[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
ON-VEHICLE REPAIR
SIDE OIL SEAL
Exploded ViewINFOID:0000000001381636
Refer to TM-635, "Exploded View".
Removal and InstallationINFOID:0000000001381637
REMOVAL
1. Remove front drive shafts. Refer to FAX-10, "Removal and Installation (Left Side)" and FA X - 11 , "Removal
and Installation (Right Side)".
2. Remove differential side oil seals (1) using a suitable tool.
CAUTION:
Do not damage transaxle case and clutch housing.
INSTALLATION
Installation is in the reverse order of removal.
 Install differential side oil seals (1) to transaxle case side (B) and
clutch housing side (C) using Tool (A).
CAUTION:
 Do not reuse differential side oil seal.
 When installing, never incline differential side oil seal.
 Do not damage clutch housing and transaxle case.
 Check oil level and oil leakage after installation. Refer to TM-628,
"Inspection".
SCIA7625E
Tool number : KV38100300
Dimension “L
1” : 1.2 - 1.8 mm (0.047 - 0.071 in)
Dimension “L
2” : 2.7 - 3.3 mm (0.106 - 0.130 in)
JPDIC0120ZZ

TM-682
< REMOVAL AND INSTALLATION >[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
K9K
Tighten bolts to the specified torque.
 Refer to CL-11, "
Removal and Installation" for CSC (Concentric Slave Cylinder) installation procedure.
 Refer to TM-674, "
Removal and Installation" for select cable and shift cable installation procedure.
 Bleed the air from the clutch hydraulic system. Refer to CL-8, "
Air Bleeding Procedure".
 After installation, check for oil leakage and oil level. Refer to TM-672, "
Inspection".
“ ” mm (in)60 (2.36) 50 (1.97)
Tightening torque
N·m (kg-m, ft-lb)62.0 (6.3, 46) Bolt symbol A B
: Transaxle to engine
: Engine to transaxle
Bolt symbol A B C
Quantity 2 2 4
“ ” mm (in)50 (1.97) 80 (3.15) 65 (2.56)
Tightening torque
N·m (kg-m, ft-lb)48 (4.9, 35)
JPDIC0054ZZ

TM-698
< DISASSEMBLY AND ASSEMBLY >[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
23. While lifting up fork rod (1), install 3rd-4th and 5th-6th fork rod
assembly to clutch housing.
CAUTION:
Replace the 5th-6th shift fork, the 3rd-4th shift fork, and the
3rd-4th and 5th-6th fork rod as a set.
24. Install retaining pin into 5th-6th shift fork using suitable tool.
CAUTION:
Do not reuse retaining pin.
25. Move 1st-2nd fork rod (1), 3rd-4th and 5th-6th fork rod assembly
(2), and reverse fork rod (3) to neutral position.
26. Install selector (4) into clutch housing.
27. Install spring of selector into return bushing.
28. Apply recommended sealant onto the mating surface of tran-
saxle case.
CAUTION:
 Remove old sealant adhering to the mating surfaces. Also
remove any moisture, oil, or foreign material adhering to
both mating surfaces.
 Check for damage on the mating surface.
 Use Genuine Liquid Gasket, Three Bond 1215 or an equiv-
alent
 Apply a continuous bead of liquid gasket to the mating surface.
29. Engage shift finger and selector by moving selector lever (1).
Install transaxle case to clutch housing.
PCIB1700E
PCIB1699E
SCIA7782E
JPDIC0110ZZ

INTAKE SENSOR
VTL-11
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
INTAKE SENSOR
Removal and InstallationINFOID:0000000001696284
REMOVAL
1. Remove the evaporator. Refer to VTL-16, "Removal and Installation".
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
2. Remove the intake sensor (1) from the evaporator (2).
CAUTION:
Mark the position of intake sensor on the evaporator for
installation.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
 Replace O-rings for A/C piping with new ones, and then apply compressor oil to it when installing it.
 Install the intake sensor in the same position as the original intake sensor.
 When recharging refrigerant, check for leaks.
ZJIA0798J

A/C UNIT ASSEMBLY
VTL-13
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
7. Remove console box assembly. Refer to IP-11, "Removal and Installation"
8. Remove the instrument stay nuts (A) and harness clamps (B),
and then remove instrument stay (1).
9. Disconnect intake sensor connector (1).
10. Remove instrument panel and pad. Refer to IP-11, "
Removal and Installation".
11. Remove side ventilator ducts. Refer to VTL-23, "
Removal and Installation".
12. Remove center ventilator ducts. Refer to VTL-23, "
Removal and Installation".
13. Remove the side kicking plates. Refer to INT-20, "
Removal and Installation".
14. Disconnect the fuel filler door cable and the rear hatch door cable (if equipped).
15. Remove A/C unit assembly bolts, steering member bolts, steering column nuts and harness clips.
16. Remove steering member, and then remove A/C unit assembly.
INSTALLATION
Installation is in the reverse order of removal.
 Fill the cooling system with coolant. Refer to CO-11, "
Changing Engine Coolant" (HR16DE), CO-35, "Chang-
ing Engine Coolant" (MR18DE), CO-58, "Refilling" (K9K).
 Recharge the refrigerant. Refer to HA-29, "
HFC-134a (R-134a) Service Procedure".
CAUTION:
 Replace O-rings for A/C piping with new ones, and then apply compressor oil to it when installing it.
 When recharging refrigerant, check for leaks.
SJIA0646E
SJIA0690E
A/C unit assembly bolt : 6.9 N·m (0.7 kg-m, 61 in-lb)
Steering member bolt : 12 N·m (1.25 kg-m, 9 ft-lb)
Steering column nut : -Refer to ST-9, "
Removal and Installation".

VTL-16
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
EVAPORATOR
EVAPORATOR
Removal and InstallationINFOID:0000000001696371
REMOVAL
1. Remove the A/C unit assembly. Refer to VTL-12, "Removal and Installation".
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
2. Remove the air conditioner filter.
3. Remove foot duct (right). Refer to VTL-23, "
Removal and Installation".
4. Remove screws (A), and then remove expansion valve cover
(1).
NOTE:
Manual A/C system shown, automatic A/C system similar.
5. Remove screws (A), and then remove evaporator cover (1).
NOTE:
Manual A/C system shown, automatic A/C system similar.
6. Remove the evaporator (1) with lower blower case (2) from the
A/C unit assembly.
7. Remove the intake sensor (3) from the evaporator (1).
CAUTION:
Note the position of the intake sensor on the evaporator for
installation.
8. Remove the evaporator (1) from the lower blower case (2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
 Replace O-rings for A/C piping with new ones, and then apply compressor oil to it when installing it.
 Install the intake sensor in the same position on the evaporator.
 When recharging refrigerant, check for leaks.
SJIA0673E
SJIA0674E
SJIA0599J

VTL-36
< ON-VEHICLE REPAIR >[MANUAL AIR CONDITIONER]
INTAKE SENSOR
INTAKE SENSOR
Removal and InstallationINFOID:0000000001700349
REMOVAL
1. Remove the evaporator. Refer to VTL-41, "Removal and Installation of Evaporator".
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
2. Remove the intake sensor (1) from the evaporator (2).
CAUTION:
Mark the position of intake sensor on the evaporator for
installation.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
 Replace O-rings for A/C piping with new ones, and then apply compressor oil to it when installing it.
 Install the intake sensor in the same position as the original intake sensor.
 When recharging refrigerant, check for leaks.
ZJIA0798J

VTL-38
< ON-VEHICLE REPAIR >[MANUAL AIR CONDITIONER]
A/C UNIT ASSEMBLY
7. Remove console box assembly. Refer to IP-11, "Removal and Installation" .
8. Remove instrument stay nuts (A) and harness clamps (B), and
then remove instrument stay (1).
9. Disconnect thermo control amp. connector (1).
10. Remove instrument panel and pad. Refer to IP-11, "
Removal and Installation".
11. Remove side ventilator ducts. Refer to VTL-48, "
Removal and Installation".
12. Remove center ventilator ducts. Refer to VTL-48, "
Removal and Installation".
13. Remove side kicking plates. Refer to INT-20, "
Removal and Installation".
14. Disconnect the fuel filler door cable and the rear hatch door cable.
15. Remove A/C unit assembly bolts, steering member bolts, steering column nuts and harness clips.
16. Remove steering member, and then remove A/C unit assembly.
INSTALLATION
Installation is in the reverse order of removal.
 Fill the cooling system. Refer to CO-11, "
Changing Engine Coolant" (HR16DE), CO-35, "Changing Engine
Coolant" (MR18DE), CO-58, "Refilling" (K9K).
 Recharge the refrigerant.
CAUTION:
 Replace O-rings for A/C piping with new ones, and apply compressor oil when installing.
 When recharging refrigerant, check for leaks.
SJIA0646E
SJIA0647E
A/C unit assembly bolt : 6.9 N·m (0.7 kg-m, 61 in-lb)
Steering member bolt : 12 N·m (1.25 kg-m, 9 ft-lb)
Steering column nut : Refer to ST-9, "
Removal and Installation".

EVAPORATOR
VTL-41
< ON-VEHICLE REPAIR >[MANUAL AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
EVAPORATOR
Removal and Installation of EvaporatorINFOID:0000000001696533
REMOVAL
1. Remove A/C unit assembly. Refer to VTL-37, "Removal and Installation".
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
2. Remove the air conditioner filter.
3. Remove foot duct (right). Refer to VTL-48, "
Removal and Installation".
4. Remove screws (A), and then remove expansion valve cover
(1).
5. Remove screws (A), and then remove evaporator cover (1).
6. Remove the evaporator (1) with lower blower case (2) from the
A/C unit assembly.
7. Remove the thermo control amp. (3) from the evaporator (1).
CAUTION:
Note the position of the thermo control amp. on the evapo-
rator for installation.
8. Remove the evaporator (1) from the lower blower case (2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
 Replace O-rings for A/C piping with new ones, and the apply compressor oil to it when installing it.
 Install the thermo control amp. in the same position on the evaporator.
 When recharging refrigerant, check for leaks.
SJIA0673E
SJIA0674E
SJIA0599J