ignition Oldsmobile Intrigue 2002 Owner's Manuals

1-4 Heated Front Seat (If Equipped)
If your vehicle has this
feature, the driver's and
passenger's heated seat
switches are located on the
instrument panel near the
comfort controls.
The driver's switch is on the left, and the passenger's
switch is on the right.
There are two settings, LO and HI. To choose the LO
setting, press the top part of the switch twice. The circle
next to LO on the switch will light, indicating the LO
setting has been selected.
To choose the HI setting, press the top part of the switch
once. The circle next to HI on the switch will light,
indicating the HI setting has been selected.
To turn the system off, press the lower part of the switch
once. The light should go out when the system is not in
use. The heated seats will turn off when the ignition is
turned off.
Reclining Front Seatbacks
The release levers for the driver's and passenger's front
seatbacks are located on the outboard sides of each front
seat cushion.
Lift the lever to release the seatback, then move the
seatback to where you want it. Release the lever to lock
the seatback in place. Pull up on the lever without pushing
on the seatback and the seatback will move forward.

1-28 Servicing Your Air Bag-Equipped Vehicle
Air bags affect how your vehicle should be serviced.
There are parts of the air bag system in several places
around your vehicle. You don't want the system to
inflate while someone is working on your vehicle. Your
dealer and the service manual have information about
servicing your vehicle and the air bag system. To
purchase a service manual, see ªService and Owner
Publicationsº in the Index.
CAUTION:
For up to 10 seconds after the ignition key is
turned off and the battery is disconnected, an air
bag can still inflate during improper service. You
can be injured if you are close to an air bag when
it inflates. Avoid yellow connectors. They are
probably part of the air bag system. Be sure to
follow proper service procedures, and make sure
the person performing work for you is qualified
to do so.
The air bag system does not need regular maintenance.
Rear Seat Passengers
It's very important for rear seat passengers to buckle up!
Accident statistics show that unbelted people in the rear
seat are hurt more often in crashes than those who are
wearing safety belts.
Rear passengers who aren't safety belted can be thrown
out of the vehicle in a crash. And they can strike others
in the vehicle who are wearing safety belts.
Rear Seat Outside Passenger Positions

2-
2-1
Section 2 Features and Controls
Here you can learn about the many standard and optional features on your vehicle, and information on starting,
shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is
working properly
-- and what to do if you have a problem.
2
-2 Windows
2
-4 Keys
2
-6 Door Locks
2
-11 Remote Keyless Entry System (If Equipped)
2
-17 Trunk
2
-18 Theft
2
-20 Passlock

2-20 New Vehicle ªBreak-Inº
2
-21 Ignition Positions
2
-22 Starting Your Engine
2
-23 Engine Coolant Heater (Option)
2
-24 Automatic Transaxle Operation
2
-29 Parking Brake
2
-30 Shifting Into PARK (P)
2
-32 Shifting Out of PARK (P)
2
-33 Parking Over Things That Burn
2
-33 Engine Exhaust2
-34 Running Your Engine While You're Parked
2
-34 Horn
2
-35 Tilt Wheel
2
-35 Turn Signal/Multifunction Lever
2
-42 Exterior Lamps
2
-45 Interior Lamps
2
-48 Mirrors
2
-52 Storage Compartments
2
-53 Ashtray and Cigarette Lighter
2
-54 Accessory Power Outlets
2
-56 OnStar
System (If Equipped)
2
-59 Power Sunroof (Option)
2
-60 HomeLink
Transmitter (If Equipped)
2
-64 The Instrument Panel -- Your
Information System
2
-68 Warning Lights, Gages and Indicators

2-3 Power Windows
Switches located on the driver's door armrest
operate each of the windows when the ignition is on.
In addition, each passenger door has an individual
window switch.Express
-Down Window
The driver's window switch has an auto
-down feature.
This switch is labeled AUTO. Tap the switch rearward,
and the driver's window will open a small amount. If the
switch is moved all the way back, the window will go all
the way down.
To stop the window while it is lowering tap the
switch forward. To raise the window, press and hold
the switch forward.
Lock
-Out Switch
The driver's window
controls also include a
lock
-out switch. Press
LOCK to stop front and rear
passengers from using their
window switches.
The driver can still operate all windows with the lock
on. Press the other side of the LOCK switch to return to
normal window operation.

2-4
Keys
CAUTION:
Leaving children in a vehicle with the ignition
key is dangerous for many reasons. A child or
others could be badly injured or even killed.
They could operate the power windows or other
controls or even make the vehicle move. Don't
leave the keys in a vehicle with children.

2-5
Master Key Spare Key
Your vehicle comes with two master keys and one spare
key. The keys can be used for the ignition, as well as all
door locks, trunk and storage compartments.
These keys don't have key plugs. Your Oldsmobile
dealer has a code for your key and can assist you if you
need a new key.
NOTICE:
Your vehicle has a number of features that can
help prevent theft. But you can have a lot of
trouble getting into your vehicle if you ever
lock your key inside. You may have to damage
your vehicle to get in. So be sure you have an
extra key.
In an emergency contact Oldsmobile Roadside
Assistance. See ªRoadside Assistanceº in the Index
for more information.
If your vehicle is equipped with the OnStar system with
an active subscription and you lock your keys inside the
vehicle, OnStar may be able to send a command to
unlock your vehicle. See ªOnStarº in the Index for
more information.

2-8
Programmable Modes
Mode 1: Last Door Closed Locking Feature is off.
Mode 2: Last Door Closed Locking Feature is on.
Before your vehicle was shipped from the factory, it was
programmed to Mode 2. The mode to which your
vehicle was programmed may have been changed since
it left the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Close all doors and turn the ignition switch to ON.
2. Press and hold the power door lock switch in the
unlock position.
3. While holding the door unlock switch, cycle the
transaxle out of and back into PARK (P). Count the
number of chimes you hear. The number of chimes
tells you which mode your vehicle is set for. (If you
do not wish to change the current mode, you can
either exit the programming mode by following the
instructions listed here or program the next feature
available on your vehicle).4. A single chime will be heard if the last door closed
locking feature is disabled, and two chimes will be
heard if the feature is enabled. After the initial
transaxle cycle, each additional cycle will turn the
last door closed locking feature on or off.
5. When the door unlock switch is released, the vehicle
will remain in the most recent operating mode.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions above or program the next feature
available on your vehicle.
Disconnecting the battery for up to a year will not
change or delete any previously programmed modes.

2-9 Programmable Automatic Door Locks
Programmable automatic door locks is a standard
feature intended to provide enhanced security and
convenience by automatically locking and unlocking
vehicle doors. The automatic locking and unlocking
of the vehicle will occur if the ignition key is in ON and
the driver's door is closed when the vehicle is shifted
out of PARK (P).
Programmable Modes
Mode 1: No automatic door lock or unlock.
Mode 2: Automatic all door lock when the transaxle is
shifted out of PARK (P). No automatic door unlock.
Mode 3: Automatic all door lock when the transaxle is
shifted out of PARK (P). Automatic all door unlock
when the transaxle is shifted into PARK (P).
Mode 4: Automatic all door lock when the transaxle is
shifted out of PARK (P). Automatic driver's door only
unlock when the transaxle is shifted into PARK (P).
Before your vehicle was shipped from the factory, it was
programmed to Mode 3. The mode to which your
vehicle was programmed may have been changed since
it left the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:1. Close all doors and turn the ignition switch to ON.
2. Press and hold the power door lock switch in the
lock position.
3. While holding the door lock switch, cycle the
transaxle out of and back into PARK (P). The door
lock and unlock functions will operate as defined,
depending upon the current mode selected. (If you
do not wish to change the current mode, you can
either exit the programming mode by following the
instructions listed here or program the next feature
available on your vehicle).
4. After an initial transaxle cycle, each additional cycle
will advance the operating mode by one, starting
from the current operating mode.
5. If cycled beyond Mode 4, the vehicle will enter
operating Mode 1. When the door lock switch is
released, the vehicle will remain in the most recent
operating mode.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions above or program the next feature
available on your vehicle.
Disconnecting the battery for up to a year will not
change or delete any previously programmed modes.

2-10 Rear-Door Security Locks
Your vehicle is equipped with rear door security locks
that help prevent passengers from opening the rear doors
of your vehicle from the inside.
To use one of these locks, do the following:
1. Open one of the rear doors.
2. On the inside of the rear
door will be a lock with
a label as shown. Slide
the lever located next to
the label upward to
engage the lock.
3. Close the door.
4. Repeat the procedure on the other rear door lock.To disengage the lock(s), reverse the steps.
The rear doors on your vehicle cannot be opened from
the inside when this feature is in use. If you want to
open the rear door when the security lock is on, unlock
the door from the inside and then open the door from
the outside.
Lockout Prevention
Lockout Prevention is a standard feature intended to
provide enhanced security and convenience. This feature
prevents a driver who has left the key in the ignition
from locking the doors using the power door lock switch
while any door is open.
This feature cannot guarantee that you will never be
locked out of your vehicle. If you don't leave the key in
the ignition, or if you use the manual door lock, you
could still lock your keys inside your vehicle. Always
remember to take your keys with you.

2-11
Programmable Modes
Mode 1: Turns feature on.
Mode 2: Turns feature off.
Before your vehicle was shipped from the factory, it was
programmed to Mode 1. The mode to which your
vehicle was programmed may have been changed since
it left the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Open a door and put the key in the ignition.
2. Hold down the power door lock switch for more than
three seconds. This will turn the feature off or on,
depending upon the current mode selected. (If you
do not wish to change the current mode, you can
either exit the programming mode by following the
instructions listed here or program the next feature
available on your vehicle).
3. When the door lock switch is released, the vehicle
will remain in the most recent operating mode.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions above or program the next feature
available on your vehicle.Remote Keyless Entry System
(If Equipped)
If your vehicle has this feature, you can lock and unlock
your doors or unlock your trunk from about 3 feet (1 m)
up to 30 feet (9 m) away using the remote keyless entry
transmitter supplied with your vehicle.
Your keyless entry system operates on a radio frequency
subject to Federal Communications Commission (FCC)
Rules and with Industry Canada.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
This device complies with RSS
-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation of
the device.