turn signal OPEL FRONTERA 1998 Manual PDF

8A–2LIGHTING SYSTEM
Vanity Mirror Illumination Bulb 8A–16. . . . . . . . . . . . .
Removal 8A–16. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A–16. . . . . . . . . . . . . . . . . . . . . . . . . . .
Starter Switch 8A–17. . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 8A–17. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A–17. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lighting Switch (Combination Switch) 8A–18. . . . . .
Removal 8A–18. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A–18. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fog Light Switch 8A–19. . . . . . . . . . . . . . . . . . . . . . . .
Removal 8A–19. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A–19. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stoplight Switch (W/O Cruise Control) 8A–20. . . . . .
Removal 8A–20. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A–20. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Switch (W/Cruise Control) 8A–21. . . . . . . . . .
Removal 8A–21. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A–21. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal Switch (Combination Switch) 8A–21. . .
Removal and Installation 8A–21. . . . . . . . . . . . . . .
Hazard Warning Switch 8A–22. . . . . . . . . . . . . . . . . .
Removal 8A–22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation 8A–22. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tailgate Switch 8A–23. . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 8A–23. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A–23. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Door Switch 8A–23. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 8A–23. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A–23. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Defogger Switch 8A–24. . . . . . . . . . . . . . . . . . .
Removal 8A–24. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A–24. . . . . . . . . . . . . . . . . . . . . . . . . . .
Seat Heater Switch 8A–25. . . . . . . . . . . . . . . . . . . . . .
Removal 8A–25. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A–25. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Key Remind Switch (Starter Switch) 8A–25. . . . . . .
Removal and Installation 8A–25. . . . . . . . . . . . . . .
Illumination Controller 8A–26. . . . . . . . . . . . . . . . . . . .
Removal 8A–26. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A–26. . . . . . . . . . . . . . . . . . . . . . . . . . .
Power/Winter Switch 8A–27. . . . . . . . . . . . . . . . . . . . .
Removal 8A–27. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8A–27. . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Data and Specifications 8A–28. . . . . . . . . . . . .
Service Precaution
WARNING: IF SO EQUIPPED WITH A
SUPPLEMENTAL RESTRAINT SYSTEM (SRS),
REFER TO THE SRS COMPONENT AND WIRING
LOCATION VIEW IN ORDER TO DETERMINE
WHETHER YOU ARE PERFORMING SERVICE ON OR
NEAR THE SRS COMPONENTS OR THE SRS
WIRING. WHEN YOU ARE PERFORMING SERVICE
ON OR NEAR THE SRS COMPONENTS OR THE SRS
WIRING, REFER TO THE SRS SERVICE
INFORMATION. FAILURE TO FOLLOW WARNINGS
COULD RESULT IN POSSIBLE AIR BAG
DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or other
corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener. When
you install fasteners, use the correct tightening
sequence and specifications. Following these
instructions can help you avoid damage to parts and
systems.

8A–10LIGHTING SYSTEM
High Mount Stoplight
Removal
1. Disconnect the battery ground cable.
2. Remove the clips(2).
3. Pull out the high mount stoplight(1).
4. Remove the connector.
5. Remove the high mount stoplight.
803RS003
Installation
1. Insert the clips(1)(3) into the high mount stoplight(2).
2. Reconnect the connector.
3. Install the high mount stoplight.
803RS004
Front Turn Signal Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the screw at the upper portion of the light
bracket, and remove the bracket from the fender.
3. Remove the front combination light(1).
4. Remove the turn signal light socket(3) by turning it
counterclockwise.
5. Remove the bulb(2) by turning it counterclockwise
while pushing it at the same time.
801RS002
Installation
To install, follow the removal steps in the reverse order.

LIGHTING SYSTEM8A–11
Side Turn Signal Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Pull the light/bulb(1) toward you while pushing the
light housing in the rear direction of the vehicle to
release its lock.
3. Remove the bulb by turning it counterclockwise while
pushing it at the same time.
801RW013
Installation
To install, follow the removal steps in the reverse order.
Rear Turn Signal Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the three screws and release the lock at two
positions.
3. Remove the rear combination light(3).
4. Remove the turn signal light socket/bulb(1) by turning
it counterclockwise.
5. Remove the bulb(2) by turning it counterclockwise
while pushing it at the same time.
803RS002
Installation
To install, follow the removal steps in the reverse order.

LIGHTING SYSTEM8A–21
Brake Switch (W/Cruise Control)
Removal
1. Disconnect the battery ground cable.
2. Disconnect the connector(1), loosen the lock nut(3)
and then remove the brake switch(2) by turning it.
310RW010
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Check to see if the brake pedal has been returned by
the return spring to the specified position.
2. Turn the switch clockwise until the tip of the threaded
portion of the brake switch contacts the pedal arm.
3. Turn the switch counterclockwise until the space
between the tip of the threaded portion and the pedal
arm is 0.5 to 1.0 mm (0.02 – 0.04 in.).
310RS003
Turn Signal Switch (Combination Switch)
Removal and Installation
Refer to the removal and installation steps of the Lighting
Switch (Combination Switch) in this section.

8A–28LIGHTING SYSTEM
Main Data and Specifications
Light and Bulb Specifications
D08RW539
Legend
(1) Dome Light
(2) Luggage Room Light
(3) Courtesy Light
(4) Side Turn Signal Light
(5) Front Turn Signal Light
(6) Clearance Light
(7) Front Combination Light
(8) Headlight
(9) Fog Light(10) Meter
(11) Map Light
(12) High Mount Step Light
(13) License Plate Light
(14) Rear combination Light
(15) Taillight/Stoplight
(16) Rear Fog Light
(17) Backup Light
(18) Rear Turn Signal Light.

LIGHTING SYSTEM8A–29
Light NameRated PowerNumber of
BulbsLens ColorRemarks
Headlight60w/55w2WhiteHalogen
FrontTurn signal light21w2Whitecombination
lightClearance light5w2Amber
FRT fog light55w2WhiteHalogen
Taillight/Stoplight5w/21w2Red
RearBumperTurn signal light21w2Ambercombination
lightTaillight/Stoplight5w/21w2RedBodyTurn signal light21w2Amber
Backup light21w2White
RR fog light21w2Red
Side turn signal light5w2Amber
License plate lightBumper5w2White
Body5W1White
High mount stoplight——RedLED
Map light5w2White
Dome light10w1White
Luggage room light8w1White
Courtesy light3.8w2White
A/C SW60mA1
RR defogger SW0.84w1
Mirror defogger SW0.84w1
FRT fog light SW0.7w1
RR fog light SW0.7w1
Cruise (Set)1.4w1Meter
Cruise (Main)1.4w1Meter
Check trans3w1Meter
Anti-theft3w1Warning box
Turn signal1.4w2Meter
Golw1.4w1Meter
Water sedimenter1.4w1Meter
Indicator/High beam1.4w1MeterWa rnin g
lightABS1.4w1Meter
Check engine1.4w1Meter
Low fuel1.4w1Meter
4WD1.4w1Meter
Oil Pressure1.4w1Meter
Brake system1.4w1Meter
Charge1.4w1Meter
Seat belt2w1Meter
A/T shift position0.91w7Meter
A/T oil temp3w1Meter

I-115
B-53
B1
H-2716
H-257
B-53
2 L
H-25100.85
R/B0.85
G/O
H-1612
HAZARD
WARNING
SW
TURN SIGNAL
LIGHT SWFLASHER
UNIT
0.85
G/B0.85
G/B
0.85
G/B0.85
P/B
0.85
P/B2.0
G/O0.3
R/G 0.85
G/R
ILLUMINATION
CONTROLLER
(3) 0.85
P/B 2.0
LG/B 0.5
B
1.25
B2.0
LG/B
2.0
LG/B
2.0
LG/B2.0
B/R2.0
B/R
0.85
R/B 0.85
R/B2.0
G/O
5.0
W BATT.(+)
F-3 15A
HORN,HAZARD3.0
B/Y STARTER SW
(IG1)
C-3 10A
TURN
BACK
B-12
B-12
4
B-12
5 3
LR
A
I-11I-11I-11I-11
64 2 1
I-117I-118I-11 TAIL RELAY
(4) BACK UP
LIGHT
3
B
B-53
3 E
HORN RELAY
(2)
H-276H-2710
B-19
BODY-RH
D08RW683

1.25
B1.25
B
0.5
B0.5
B 0.85
P/B 0.85
P/B
RR TURN
SIGNAL
LIGHT-RH
(BODY)FRT TURN
SIGNAL
LIGHT-RHSIDE TURN
SIGNAL
LIGHT-RHR-124
H-3222
1
R-12
0.85
P/B
C-313
1
1
C-311
H-7
0.85
P/B 0.85
P/B0.85
P/B
C-611
2
C-61
B
7
H-15
C-167C-39
FENDER-LH FENDER-RH FENDER-LH
A
C-701
C-70
2
C-223
C-22
1
H-714
C-16 0.5
B
SIDE TURN
SIGNAL
LIGHT-LHFRT TURN
SIGNAL
LIGHT-LH
0.5
B 0.85
G/B 0.85
G/B 0.85
G/B0.85
G/B
TURN SIGNAL
INDICATOR
LIGHT
(METER)
8
C-16
FENDER-LH1
R-134
H-3221
R-13
1
RR TURN
SIGNAL
LIGHT-LH
(BODY)
0.85
G/B
R-4
BODY-RR
D08RWC67

1.25
B
1.25
B 1.25
B
1.25
B1.25
B
0.5
B0.5
B
RR TURN
SIGNAL
LIGHT-RH
(BUMPER)FRT TURN
SIGNAL
LIGHT-RHSIDE TURN
SIGNAL
LIGHT-RH
0.85
P/B
C-313
1
1
C-311
H-7
0.85
P/B 0.85
P/B0.85
P/B
C-611
2
C-61
B
7
H-15
C-167C-39
FENDER-LH FENDER-RH FENDER-LH
A
C-701
C-70
2
C-223
C-22
1
H-714H-719
C-16 0.5
B
SIDE TURN
SIGNAL
LIGHT-LHFRT TURN
SIGNAL
LIGHT-LH
0.5
B 0.85
G/B 0.85
G/B 0.85
G/B0.85
G/B
0.85
G/O
0.85
G/O0.85
P/L
0.85
P/L 0.85
G/BTURN SIGNAL
INDICATOR
LIGHT
(METER)
TRAILER HARNESS
CONNECTOR
8
C-16
FENDER-LH1
F-71
H-3221
H-3311
F-7
H-332
F-81
F-8
2
6RR TURN
SIGNAL
LIGHT-LH
(BUMPER)
0.85
G/B0.85
P/B
0.85
P/B
H-3222
H-335
H-44
4
H-591
H-443
H-3320
H-592
H-447
0.85
P/B
R-4
BODY-RR
D08RWC66

I-115
B-53
B1
H-204
H-202
B-53
2 L
H-25170.85
R/B0.85
G/O
H-1614
HAZARD
WARNING
SW
TURN SIGNAL
LIGHT SWFLASHER
UNIT
0.85
G/B0.85
G/B
0.85
G/B0.85
P/B
0.85
P/B2.0
G/O0.3
R/G 0.85
G/R
ILLUMINATION
CONTROLLER
(3) 0.85
P/B 2.0
LG/B 0.5
B
1.25
B2.0
LG/B
2.0
LG/B
2.0
LG/B2.0
B/R2.0
B/R
0.85
R/B 0.85
R/B2.0
G/O
5.0
W BATT.(+)
F-3 15A
HORN,HAZARD3.0
B/Y STARTER SW
(IG1)
C-3 10A
TURN
BACK
B-12
B-12
4
B-12
5 3
LR
A
I-11I-11I-11I-11
64 2 1
I-117I-118I-11 TAIL RELAY
(4) BACK UP
LIGHT
3
B
B-53
3 E
HORN RELAY
(2)
H-2519H-2520
B-19
BODY-LH
D08RW872