light PEUGEOT 2008 2016 User Guide

33
2008_en_Chap01_controle-de-marche_ed01-2016
Coolant temperature
gauge
With the engine running, when the needle is:
- i n zone A , the temperature is correct,
-

i
n zone B, the temperature is too high;
the maximum temperature and the
central STOP warning lamps come on,
accompanied by an audible signal and a
warning message in the screen.
You MUST stop as soon as it is safe to
do
so.
Wait a few minutes before switching off the
engine.
Contact a PEUGEOT dealer or a qualified
workshop. After driving for a few minutes, the temperature
and pressure in the cooling system increase.
To top up the level:
F

w
ait for the engine to cool,
F
u
nscrew the cap slightly to allow the
pressure to drop,
F
w
hen the pressure has dropped, remove
the cap,
F
t
op up the level to the "MA X" mark.
Be aware of the risk of burns when
topping up the cooling system. Do not
fill above the maximum level (indicated
on the header tank).
1
Monitoring

34
Touch screen
For reasons of safety, the driver
should only carr y out operations
that require close attention, with the
vehicle stationary.
Some functions are not accessible
when driving.
It gives access to:
-

m

enus for adjusting settings for vehicle
functions and systems,
-

a

udio and display configuration menus,
-

a

udio system and telephone controls and
the display of associated information.
And, depending on equipment, it allows:
-

t

he display of alert messages and the
visual parking sensors information,
-

a

ccess to the controls for the navigation
system and Internet services, and the
display of associated information.
General operation
Recommendations
It is necessary to press firmly, particularly for
"flick" gestures (scrolling through lists, moving
the map...).
A light wipe is not enough.
The screen does not recognise pressing with
more than one finger.
This technology allows use at all temperatures
and when wearing gloves.
Do not use pointed objects on the touch
screen.
Do not touch the touch screen with wet hands.
Uses a soft clean cloth to clean the touch
screen.
State of indicator lamps
Some buttons contain an indicator lamp that
gives the state of the corresponding function.
Green indicator: you have switched on the
corresponding function.
Orange indicator: you have switched off the
corresponding function.
Principles
Press the " MENU" button for access to the
different menus, then press the virtual buttons
in the touch screen.
Each menu is displayed over one or two pages
(primary page and secondary page).
Use this button to go to the
secondary page.
After a few moments with no action on
the secondary page, the primary page
is displayed automatically. Use this button to return to the
primary page.
Use this button for access to
additional information and to the
settings for certain functions.
Use this button to confirm.
Use this button to quit.
Monitoring

37
2008_en_Chap01_controle-de-marche_ed01-2016
"Driving" menu
The functions accessible from this menu are detailed in the table below.Button Corresponding function Comments
Vehicle settings The functions with settings that can be adjusted are grouped together under these tabs:
-
"Driving assistance "
●

"
Automatic rear wiper in reverse" (Activation of rear wiper coupled to reverse gear; see
the corresponding section)
-
"Lighting "
●

"
Guide-me-home lighting" (Automatic guide me home lighting; see the corresponding
section),
●

"
LED daytime running lamps" (see the corresponding section),
●

"
Mood lighting" (Interior mood lighting; see the corresponding section).
Select or deselect the tabs at the bottom of the screen to display the functions required.
Speed settings Memorisation of speeds for use with the speed limiter or cruise control.
Under-inflation initialisation Initialisation of the under-inflation detection system.
1
Monitoring

43
2008_en_Chap02_ouvertures_ed01-2016
System for the central unlocking or locking
of the vehicle using the door lock or from a
distance.
It is also used to locate and start the vehicle, as
well as providing protection against theft.
Remote control key
Unlocking the vehicle
F Turn the key in the driver's door lock towards the front of the vehicle to unlock it.
Using the remote control
F Press the open padlock to unlock the vehicle.
Unlocking is confirmed by rapid
flashing of the direction indicators for
approximately 2 seconds.
According to version, the door mirrors
unfold at the same time.
Unlocking with the key does not
deactivate the alarm.
F

P

ress this button to unfold the key.
A. U
nfolding / Folding.
B.


Unlocking.
D

isarming the alarm.
C.


Locking.
L

ocating the vehicle.
A

rming the alarm.
D.
G

uide-me-home lighting.
Unfolding the key
Using the key
2
Access

44
2008_en_Chap02_ouvertures_ed01-2016
Locking is confirmed by fixed
lighting of the direction indicators for
approximately 2 seconds.
According to version, the door mirrors
fold at the same time.
As a safety measure (children on
board), never leave the vehicle without
taking your key, even for a short period.
Locking the vehicle
Using the remote control
F Press the closed padlock to lock the vehicle.
F

T

urn the key in the driver's door lock
towards the rear to lock the vehicle.
Maintaining the locking action (key or remote
control) automatically closes the windows. If one of the doors or the boot is still
open or if an electronic key has been
left inside the vehicle, the central
locking does not take place.
When the vehicle is locked, if it is
unlocked inadvertently, it will lock
itself again automatically after about
30
seconds unless a door is opened.
When the key is in the ignition switch,
its locking/unlocking functions are
deactivated.
The folding and unfolding of the door
mirrors by the remote control can be
deactivated by a PEUGEOT dealer or a
qualified workshop.
Using the key
Access

45
2008_en_Chap02_ouvertures_ed01-2016
Folding the key
F A press switches on the vehicle's lighting and flashes the direction
indicators for a few seconds to
help you locate your vehicle in a
car park.
Locating your vehicle
If you do not press the button when
folding the key, there is a risk of
damage to the mechanism. The original key contains a coded electronic
chip. When the ignition is switched on, starting
is only possible if the code is detected and
recognised.
This protection against theft locks the engine
management system a few moments after the
ignition is switched off and prevents starting of
the engine following a break-in.
Guide-me-home

lighting
Make a long press on this button to
operate the guide-me-home lighting
(switching on the sidelamps, dipped
beams and number plate lamps).
A second press before the end of the timed
period cancels the guide-me-home lighting.
Electronic engine immobiliser
In the event of a fault, you are
informed by illumination of the
warning lamp, an audible signal and
the display of a message.
In this case, your vehicle will not start; contact
a PEUGEOT dealer as soon as possible.
Keep away from your vehicle, the
label attached to the keys given to you
on acquisition of the vehicle. It will
help in finding the original code for
replacement of the key.
F
P
ress this button before folding the key.
Advice
2
Access

46
2008_en_Chap02_ouvertures_ed01-2016
Changing the battery
Battery ref.: CR1620 / 3 volts.Do not throw the remote control
batteries away, they contain metals
which are harmful to the environment.
Take them to an approved collection
point.
Remote control problem
Reinitialisation
F Switch off the ignition.
F
T urn the key to position 2 (Ignition) .
F

P
ress the closed padlock immediately for a
few seconds.
F

S
witch off the ignition and remove the key
from the ignition switch.
The remote control is fully operational again. Following disconnection of the vehicle battery,
replacement of the remote control battery or
in the event of a remote control malfunction,
you can no longer unlock, lock or locate your
vehicle.
F
F
irst of all, use the key in the lock to unlock
or lock your vehicle.
F
T
hen, reinitialise the remote control.
If the problem persists, contact a PEUGEOT
dealer as soon as possible.
If the battery is flat, you are informed
by lighting of this warning lamp in the
instrument panel, an audible signal
and a message in the screen.
F
U
nclip the cover using a screwdriver in the
cutout.
F
R
emove the cover.
F
E
xtract the flat battery from its location.
F P lace the new battery into its location
observing the original direction.
F

C
lip the cover in place.
Access

61
2008_en_Chap03_confort_ed01-2016
Automatic "electrochrome"
model
This system automatically and progressively
changes between the day and night uses by
means of a sensor, which measures the light
from the rear of the vehicle.
Equipped with an anti-dazzle system, which darkens the mirror glass and reduces the nuisance to
the driver caused by the sun, headlamps from other vehicles...
Rear view mirror
Manual model
Adjustment
F
A djust the mirror so that the glass is
directed correctly in the "day" position.
Day / night position
F

P
ull the lever to change to the "night" anti-
dazzle position.
F

P
ush the lever to change to the normal
"day" position. In order to ensure optimum visibility
during your manoeuvres, the mirror
lightens automatically when reverse
gear is engaged.
3
Comfort

65
2008_en_Chap03_confort_ed01-2016
If you place the air flow control at
position 0 (off), the temperature in the
vehicle will no longer be maintained.
However, a slight flow of air can still be
felt due to the movement of the vehicle.
Manual air conditioning
1. Temperature adjustment.
2. Air flow adjustment.
3.
A

ir distribution adjustment.
4.
A

ir intake/ air recirculation.
5.
A

ir conditioning On / Off.Temperature
F Turn the knob from blue (cold) to red (hot) to adjust the
temperature to your wishes.
Air flow
F Turn the knob from position 1 to position 6 , to obtain the desired
air f low.
Manual mode
Heating / Ventilation
3
Comfort

69
2008_en_Chap03_confort_ed01-2016
F Press this button several times in succession to direct the air flow
in turn towards:
-

t
he windscreen, the side
windows and the footwells,
-

t
he windscreen and side
windows (demisting or
def r o st ing),
-

t
he central and side vents,
-

t
he central vents, the side
vents and the footwells,
-

t
he footwells. F

P
ress this button to recirculate
the interior air. The indicator
lamp in the button comes on and
the air recirculation symbol is
displayed. When you modify a setting, the indicator lamp
in the "AUTO"
button goes off.
F

P
ress this "full fan" button to
increase the air flow.
F

P
ress this "empty fan" button to
reduce the air flow. Avoid prolonged operation in interior air
recirculation mode (risk of misting and
of deterioration of the air quality).
Avoid driving for too long with the
system switched off (risk of misting and
of deterioration of the air quality).
Air distribution
Air flow
The air flow symbol (a fan) appears in the
screen. It is filled in progressively in relation to
the value required.
Air intake/Air recirculation
Air recirculation prevents exterior odours
and fumes from entering the passenger
compartment. It is activated automatically when
operating the screenwash.
Manual mode
Switching the system off
Switching on
Switching off
F

A
s soon as possible, press this button
again to permit the intake of exterior air and
prevent misting. The indicator lamp in the
button goes off. Depending on your requirements, you can
make a different selection from that offered by
the system by changing a setting. The other
functions will still be controlled automatically.
F

P
ress the "empty fan" air flow
button until the fan symbol
disappears and "---" appears.
This action switches off all of the functions of the
air conditioning system.
The temperature is no longer maintained at a
comfortable level. However, a slight flow of air, due
to the movement of the vehicle, can still be felt.
Pressing the "full fan" button
reactivates the system with the
settings prior to deactivation.
3
Comfort