wheel Peugeot 208 2017 Owner's Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2017, Model line: 208, Model: Peugeot 208 2017Pages: 304, PDF Size: 11.45 MB
Page 127 of 304

125
To register a speed higher than the previous
setting, there are two possibilities.
Without using the accelerator
- Press the SET + button.
A short press increases the speed setting by
1
mph (km/h).
Pressing and holding increases the setting in
steps of 5
mph (km/h).
By using the accelerator
- Exceed the saved speed until you reach the desired speed. -
P
ress the SET – or
SET + button.
To register a speed lower than the previous
setting:
-
P
ress the SET –
button.
A short press decreases the setting by 1 mph
(km/h).
Pressing and holding decreases the setting in
steps of 5 mph (km/h).
Switching the system off
- Place the thumbwheel at the 0 position:
cruise control mode is deselected. The
display returns to the total mileage recorder.
After switching off the ignition, all registered
speed settings are lost.
Operating fault
The registered speed is erased, then replaced
by three dashes.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
Changing the registered
speed setting
6
Driving
Page 130 of 304

128
The collision can be automatically avoided
if the speed difference between your
vehicle and the one ahead is not more
than 9 mph (15 km/h).
Above this threshold, the system will do
what is possible to avoid or reduce the
seriousness of the accident by lowering
the speed of impact.
Activation / Deactivation
It is possible to activate or
deactivate the Active City Brake
from the Driving / Vehicle menu.
The system state remains in memory when the
ignition is switched off.
Each subsequent time the ignition is switched
on, if the automatic emergency braking function
is deactivated, a temporary message will
be displayed indicating the speed threshold
(6
mph (10 km/h)). Please deactivate the Active City
Brake:
-
F
ollowing impact damage to the
windscreen close to sensor,
-
W
hen towing a trailer,
-
W
hen the vehicle is being towed,
-
W
hen the vehicle is about to cross a
toll barrier.
-
W
hen the vehicle is passing through
an automatic car wash,
Operating limits
Not detected are:
- Pe destrians, animals, motorcyclists,
cyclists.
-
F
ixed and non-reflective materials and
objects (cardboard box, wall, etc.).
-
V
ehicles not travelling in the same direction.
This system will not trigger or inter vene if the
driver:
-
p
resses the accelerator pedal firmly,
-
t
urns the wheel sharply (avoiding
manoeuvre).
-
m
ay stop the vehicle, holding the brakes on
for around 1.5
seconds when stationary to
allow the driver time to take back control of
the vehicle,
-
m
ay cause the engine to stall,
-
m
ay give rise to a pumping noise, due to the
pressurisation of the braking system.
Operating faults
Clean or clear any dirt, mist or objects (stickers,
leaves, etc.) from the top of the windscreen that
could obstruct the laser's field of vision. In the following cases, you should have the
system checked by a PEUGEOT dealer or a
qualified workshop:
-
T
he message "
Automatic braking system "
fault detected accompanied by an audible
signal indicates that a fault has been
detected.
-
F
ollowing an impact, the system is
automatically put out of ser vice, it no longer
works. The system detects the deployment
of airbags.
Do not attempt to remove, adjust or test
the sensor.
Only a PEUGEOT dealer or a qualified
workshop is able to work on the system.
Misting of the windscreen or accumulations
of snow on the bonnet could inter fere with the
operation of the laser. A message appears if
the laser is obstructed.
Use windscreen demisting and regularly clean
the area of the windscreen in front of the
sensor.
Be particularly vigilant when driving in poor
weather (very heavy rain, hail, fog, snow, etc.).
This is because braking distances increase
while the laser's calculation parameters remain
the same.
Driving
Page 133 of 304

131
Park Assist
The system detects a parking space and then
provides assistance with the parallel parking
manoeuvres.
It controls the steering and provides visual and
audible information to the driver.
The driver manages the accelerator, brakes,
gears and the clutch in the case of a manual
gearbox.
The driver can take control at any time by
gripping the steering wheel.The Park Assist system cannot in any
circumstances replace the need for
vigilance on the part of the driver.
The driver must remain in control of their
vehicle ensuring that the space remains
clear during the manoeuvre.
In some circumstances, the sensors may
not detect small obstacles located in their
blind spots.
During manoeuvring phases, the steering
wheel per forms rapid turns: do not hold
the steering wheel, do not put your hands
between the spokes of the steering wheel.
Watch out for any object that could block
the manoeuvre (loose clothing, scar ves,
ties, etc.) – Risk of injury! For entry into a parallel parking space the
system does not detect spaces which are
clearly much smaller or larger than the
size of the vehicle.
The "Parking sensors" function activates
automatically during the manoeuvres, it is
possible that a warning lamp illuminates
on the screen, accompanied by an audible
signal, without affecting the parking.
Changing tyre sizes (out-size tyres, winter
tyres, etc.) can inter fere with the correct
operation of the parking assistance
system.
When the Park Assist is active, it prevents
the Stop & Start going into STOP mode.
In STOP mode, activating Park Assist
restarts the engine.
Entering a parallel parking
space
F Once you have detected an available space,
limit the speed of the vehicle to 12 mph
(20
km/h).
F
P
osition your vehicle before this space.
The system provides assistance in entering and
exiting a parking space when parallel parking.
6
Driving
Page 134 of 304

132
To activate the Park Assist system:
F
P
ress this control.
The indicator lamp in the control remains off.
A message is displayed in the screen.
F
S
elect the enter parking space manoeuvre.
The indicator lamp in the control comes on.
F
O
perate the direction indicator on the
parking side. F
M
ove for wards alongside the parking
space at a speed below 12
mph (20 km/h)
to measure it, keeping at a distance of
between 0.5 and 1.5
metres from the row of
parked vehicles.
Once measurement is complete, if the space is
large enough a message indicates that parking
is possible.
F
M
ove your vehicle for ward until a new
message is displayed. F
S
elect reverse and release the steering
wheel.
The assisted parking manoeuvre is in progress.
Without exceeding 5
mph (8 km/h), continue
the manoeuvres following the information given
by the "parking assistance" system, until the
end of manoeuvre message is displayed.
The indicator lamp in the control goes off,
accompanied by an audible signal.
Driving
Page 135 of 304

133
The driver takes back control of the vehicle's
steering.
Exit from a parallel parking
space
F When you want to exit from a parallel parking space, start the engine.
With the vehicle stationary, to activate the Park
Assist system:
F
P
ress this control.
The indicator lamp in the control remains off.
A message is displayed in the screen. F
S
elect the exit parking space manoeuvre.
The indicator lamp in the control comes on.
F
O
perate the direction indicator on the exit
from parking side.
The direction indicator flashes throughout
the manoeuvre, whatever the position of the
control stalk.
F
S
elect a for ward or reverse gear then
release the steering wheel.
The assisted exit from parking manoeuvre is in
progress.
Without exceeding 3 mph (5 km/h), continue
the manoeuvres following the information given
by the "parking assistance" system, until the
end of manoeuvre message is displayed.
The manoeuvre is complete once the front
wheels of the vehicle are out of the parking
space.
The indicator lamp in the control goes off,
accompanied by an audible signal. The driver takes back control of the vehicle's
steering.
Deactivation
The system is deactivated automatically:
-
o n switching off the ignition,
-
i
f the engine stalls,
-
i
f no manoeuvre is per formed within
5
minutes of selecting the type of
manoeuvre,
-
a
fter a prolonged stop of the vehicle during
a manoeuvre,
-
i
f the road wheel anti-slip regulation (ASR)
is triggered,
-
i
f the speed of the vehicle exceeds the
stated limit,
-
w
hen the driver interrupts movement of the
steering wheel,
-
i
f the driver presses the Park Assist control,
6
Driving
Page 136 of 304

134
If the system is deactivated during a
manoeuvre, the driver should reactivate it
manually to repeat the measurement.
-
i
f the vehicle cannot be properly positioned
(too many manoeuvres to get the vehicle in
or out),
-
i
f the driver's door is opened,
-
i
f one of the front wheels encounters an
obstacle.
A message is displayed in the screen.
The driver then takes back control of the
vehicle's steering.
Deactivation
The system is switched off automatically:
- w hen towing a trailer,
-
i
f the driver's door is opened,
-
i
f the speed of the vehicle is above 42 mph
(70
km/h).
To switch the system off for a prolonged period,
contact a PEUGEOT dealer or a qualified
workshop.
This warning lamp comes on in
the instrument panel and/or a
message appears on the screen,
accompanied by an audible signal
(short beep).
The indicator lamp flashes for a few seconds. If
the problem occurs while using the system, the
indicator lamp goes off.
These warning lamps indicate a fault
with the power steering.
Contact a PEUGEOT dealer or a qualified
workshop.
If the lateral distance between your vehicle
and the space is too great, the system may
not be able to measure the space.
Anything projecting beyond the dimensions
of the vehicle is not taken into account by
the Park Assist system during a manoeuvre.
In bad weather and in winter, ensure that
the sensors are not covered by road dirt,
ice or snow.
In the event of a fault, have the system
checked by a PEUGEOT dealer or a
qualified workshop.
Driving
Page 137 of 304

135
Under-inflation detection
This system automatically monitors the tyre
pressure while driving.
The system monitors the pressure in all four
tyres, once the vehicle is moving.
It compares the information given by the
wheel speed sensors with reference values,
which must be reinitialised after ever y tyre
pressure adjustment or wheel change.
The system triggers an alert as soon as it
detects a drop in the pressure of one or more
tyres.
The tyre under-inflation detection system
does not replace the need for vigilance on
the part of the driver.
This system still requires you to check the
tyre inflation pressure (including the spare
wheel) every month as well as before a
long journey.
Driving with under-inflated tyres impairs
handling, extends braking distances and
causes early tyre wear, particularly in
adverse conditions (heavy loads, high
speeds, long journeys). Driving with under-inflated tyres
increases fuel consumption.
The tyre pressure specifications for your
vehicle can be found on the tyre pressure
label.
For more information on Identification
markings , including in particular the tyre
pressure label, refer to the corresponding
section.
Tyre pressures should be checked when
the tyres are "cold" (vehicle stopped for
1
hour or after a journey of less than
6
miles (10 km) at moderate speeds).
In the contrary case(hot), add 0.3
bar to
the values indicated on the label.
Under-inflation alert
This is indicated by fixed illumination
of this warning lamp, an audible
signal and, depending on the
equipment installed, a message
displayed on the screen.
F
R
educe speed immediately, avoid excessive
steering movements and sudden braking. The loss of pressure detected does not
always cause visible bulging of the tyre.
Do not be satisfied with just a visual
check.
F
I
n the event of a puncture, use the
temporary puncture repair kit or the spare
wheel (depending on equipment),
or
F
i
f you have a compressor, such as the one
in the temporary puncture repair kit, check
the pressures of the four tyres when cold,
or
F
i
f it is not possible to make this check
immediately, drive carefully at reduced
speed.
The alert is kept active until the system is
reinitialised.
The under-inflation alert can only be relied
on if the reinitialisation of the system has
been done with the pressures in the four
tyres correctly adjusted.
F
S
top the vehicle as soon as it is safe to do
so.
6
Driving
Page 138 of 304

136
Reinitialisation
The system must be reinitialised after any
adjustment to the pressures of one or more
tyres, and after changing one or more wheels.Before reinitialising the system, ensure
that the pressures of the four tyres are
correct for the use of the vehicle and in
line with the recommendations on the tyre
pressure label.
The under-inflation alert can only be relied
on if the reinitialisation of the system has
been done with the pressures in the four
tyres correctly adjusted.
The under-inflation detection system
does not give a warning if a pressure is
incorrect at the time of reinitialisation.
Without touch screen
F With the ignition on and the vehicle stationary, press this button for about
3
seconds then release it, an audible signal
confirms the reinitialisation.
With touch screen
Snow chains
The system does not have to be
reinitialised after fitting or removing snow
chains.
Operating fault
The flashing and then fixed illumination of the
under-inflation warning lamp accompanied
by illumination of the Ser vice warning lamp
indicates a fault with the system.
In this case, under-inflation monitoring of the
tyres is no longer assured.
Have the system checked by a PEUGEOT
dealer or a qualified workshop.
After carrying out any work on the system,
the pressures of the four tyres must be
checked and the system reinitialised.
Initialisation of the system is done with the
ignition on and the vehicle stationary.
The guide-me-home lighting can be
configured in the menu Driving /
Vehicle.
The new pressure parameters saved are
treated as reference values by the system.
Driving
Page 143 of 304

141
Snow chains
In wintry conditions, snow chains improve
traction as well as the behaviour of the vehicle
when braking.The snow chains must be fitted only to the
front wheels. They must never be fitted to
"space-saver" type spare wheels.
Take account of the legislation in force
in your country on the use of snow
chains and the maximum running speed
authorised.
Installation tips
F If you have to fit the chains during a journey, stop the vehicle on a flat sur face on the side
of the road.
F
A
pply the parking brake and if necessary
put wheel chocks against the wheels to
prevent your vehicle from sliding.
F
F
it the chains following the instructions
provided by the manufacturer.
F
M
ove off gently and drive for a few seconds,
without exceeding 30
mph (50 km/h).
F
S
top your vehicle and check that the snow
chains are correctly tightened.
It is strongly recommended that before
you leave, you practise fitting the snow
chains on a level and dry sur face.
Avoid driving with snow chains on roads
that have been cleared of snow, to avoid
damaging your vehicle's tyres and the
road sur face. If your vehicle is fitted with
alloy wheels, check that no part of the
chain or its fixings is in contact with the
wheel rim.
Travelling abroad
Cer tain fuels could damage the engine
of your vehicle.
In cer tain countries, the use of a
par ticular fuel may be required
(specific octane rating, specific trade
name, etc.) to ensure correct operation
of the engine.
For any additional information, contact a
dealer.
7
Practical information
Page 144 of 304

142
Only use the chains designed to be fitted to the
type of wheels fitted to your vehicle:Original tyre size Maximum link size
185/65 R15 9
mm
195/55 R16
2 0 5 /4 5 R17 7
mm
For more information on snow chains, contact a
PEUGEOT dealer or a qualified workshop.Towing a trailer
Your vehicle is primarily designed for
transporting people and luggage, but it may
also be used for towing a trailer.
We recommend the use of genuine
PEUGEOT towbars and their harnesses
that have been tested and approved from
the design stage of your vehicle, and that
the fitting of the towbar is entrusted to a
PEUGEOT dealer or a qualified workshop.
If the towbar is not fitted by a PEUGEOT
dealer, it must still be fitted in accordance
with the vehicle manufacturer's
instructions. Driving with a trailer places greater
demands on the towing vehicle and the
driver must take particular care.
For more information on Driving advice
,
particularly when towing, refer to the
corresponding section.
Please respect the maximum authorised
towable weights, indicated on the
registration certificate or in your vehicle’s
technical data.
For more information on Weights (and the
towed loads which apply to your vehicle)
refer to the corresponding section.
Obser ve the legislation in force in the
country in which you are driving.
Practical information