ECO mode Peugeot 306 Break 2002 Owner's Manual

YOUR 306 AT A GLANCE
6
FRONT AIRBAGS Disarming the passenger airbag Insert the ignition key in switch 1
and turn it:
Ð to the ÒONÓposition, the pas-
senger airbag is armed,
Ð to the ÒOFFÓposition, the pas-
senger airbag is not armed.
THE REMOTE CONTROL
A single press on button Alocks
the doors and boot or tailgate.
A single press on button Bunlocks
the vehicle.
KEYS
Using the key in the driverÕs door lock will lock or unlock the doorsand boot or tailgate.
Passenger airbag precautions
For a vehicle fitted with a disarm- ing switch:
Ð disarm theairbag if youinstall arearwards-facing childseat.
Ð arm the airbag whenan adult is inthe seat.
For a vehicle not fitted with a dis-arming switch:
Ð do not install rear-wards-facing childseats on the frontpassenger seat.
Never place your feet or anyobject on the fascia.
A
B
Operational Check This is by means of the warning light on the instrument panel. If the passenger airbag is armed or if your vehicle is not fitted with apassenger airbag, the warninglight comes on for 6 seconds whenthe ignition is switched on. If the passenger airbag is notarmed, one of the warning lightsremains on. Always contact your PEUGEOT dealer if the warning light flashes.
108
**** According to model.

TRADE NAMES OF APPROVED AND RECOMMENDED LUBRICANTS IN EUROPE(1)
F
NL
SF
GR
A
D
CH
I
N
P
E
B
DK
GB
L
S
IRL
(1) Minimum quality level: petrol: ACEA A3 and API SH/SJ ; Diesel ACEA B3 and API CF/CD -
ACEA= Association des Constructeurs EuropŽens Automobiles (Association of European Automobile Manufacturers) - API= American Petroleum Institute.
If oil is used which does not conform to the ACEA A3-B3 standards, this requires the "Arduous conditions" servicing schedule to be followed, which involves shorter intervals between services * This Fuel Economy oil may only be used in engines specifically designed for it (from 2000 Model Year).
ACTIVA D
IE SE L 7000
10W 40
AC TIVA D
IE SE
L 9000
5W 40
AC TIV
A 9000
5W 30*
U
LT R AD
IE
SE L
10W 40
U LT R A
5W 30*
U LT R O
N D
IES EL
5W 40
QUAR TZ D IE
S
EL 7000
10W 40
Q U
AR TZ 9000
5W 40
Q UAR
TZ 9000
5W 30*
AC TIVA 7000
10W 40
AC TIVA 9000
5W 40
AC TIVA 9000
5W 30*
Q U
AR TZ 7000
15W 50
U
LT R A
10W 40
U LT R A
5W 30*
U LT R O
N

5W 40
U LT R ON

0W 30
QU
AR TZ 7000
10W 40
Q UAR TZ 9000
0W 40
Q UAR TZ 9000
5W 40
Q U
AR TZ 9000
5W 30*
DIESEL
DIESEL
PETROL PETROL
24
TOTAL

92
YOUR 306 IN DETAIL
1Low coolant level*.
2 Headlamp main beam.
3 Pre-heat (Diesel).
4 Headlamp dipped beam.
5 Water in fuel filter warning light* (Diesel).
6 Speedometer.
7 Left indicator.
8 Low oil pressure warning light.
9 Handbrake low brake fluid level andelectronic brake force distribution.
10 Battery charge. 11
Right indicator.
12 Rev counter.
13 Front fog lamps*.
1 4 Rear fog lamp.
15 ABS: anti-lock braking system*.
16 Fuel gauge.
17 Low fuel level.
18 STOP warning.
19 Seat belt not fastened warning light*.
20 Disarming of passenger airbag**. 21
Side airbags warning light*.
22 Front* and side** airbag warninglight and disarming passengerairbag*.
23 Autodiagnostics*.
24 Trip recorder and service indicator.
25 Trip recorder zero reset and clocksetting.
26 Coolant temperature gauge.
* According to specification or country.
** According to model.
56 78 910 11 12 13 14 15
4 321
26 25 24 23 22 21 20 19 18 17 16
INSTRUMENT PANEL

93
YOUR 306 IN DETAIL
13 14
1Low coolant level.
2 Headlamp main beam.
3 Headlamp dipped beam.
4 Speedometer.
5 Left indicator.
6 Low oil pressure warning light.
7 Handbrake low brake fluid level and electronic brake force distribution.
8 Battery charge.
9 Right indicator.
10 Rev counter.
11 Front fog lamps. 12
Brake pad wear warning light*.
13 Rear fog lamp.
14 ABS: anti-lock braking system*.
15 Fuel gauge.
16 Low fuel level.
17 Oil level and temperature gauge.
18 STOP warning.
19 Seat belt not fastened warninglight*.
20 Disarming of passenger airbag**.
21 Side airbags warning light*. 22
Front* and side** airbag warninglight and disarming passengerairbag*.
23 Autodiagnostics*.
24 Trip recorder and service indicator.
25 Trip recorder zero reset and clocksetting.
26 Coolant temperature gauge.
* According to specification or country.
** According to model.
12 3 4 56789 1 0 11 1 2
26 25 24 23 22 21 20 19 18 17 16 15
13 14
INSTRUMENT PANEL

94
YOUR 306 IN DETAIL
1Low coolant level*.
2 Headlampt main beam.
3 Pre-heat (Diesel).
4 Headlamp dipped beam.
5 Water in fuel filter warning light* (Diesel).
6 Speedometer.
7 Left indicator.
8 Low oil pressure warning light.
9 Gear indicator (automatic gearbox).
10 Handbrake low brake fluid level andelectronic brake force distribution. 11
Battery charge.
12 Right indicator.
13 Rev counter.
14 Front fog lamps*.
15 Rear fog lamp.
16 ABS: anti-lock braking system*.
17 Fuel gauge.
18 Low fuel level.
19 Oil level.
20 STOP warning.
21 Seat belt not fastened warninglight*. 22
Disarming of passenger airbag**.
23 Side airbags warning light**.
24 Front* and side** airbag warninglight and disarming passengerairbag*.
25 Autodiagnostics*.
26 Trip recorder and service indicator.
27 Trip recorder zero reset and clocksetting.
28 Coolant temperature gauge.
* According to specification or country.
** According to model.
56 78910 11 12 13 14 15 16
4 321
28 27 26 25 24 23 22 21 20 19 18 17
INSTRUMENT PANEL

96
YOUR 306 IN DETAILAnti-lock braking system (ABS) warninglight* It comes on for 3 seconds each time the ignition is
switched on. If it comes on at over 8 m.p.h. (12 km/h.) it indicates a malfunc-
tion of the ABS.
However, the vehicle retains con- ventional servo-assisted braking.
Contact a PEUGEOT dealer.
Oil level and temperature gauge* When the ignition is switched on, this indicates the oil level (see Oil Gaugesection). After approximately 15 seconds, the graduated section and the oil level
symbol go out. The oil temperature isthen shown.
- needle in zone
E, the temperature
is correct.
- needle in zone F, the temperature
is too high. To lower the oil temper- ature, reduce your speed.
Diesel pre-heat light If the light comes on, wait until it goes out before trying
the starter.
If the engine is warm enough, the lightwill not come on, and you can startthe engine without waiting. Front air bags*, sideair bags** anddisarming thepassenger air bag*
For operation, see section onAIR BAGS.
Side air bags** For operation, see
section on AIR BAGS.
* According to specification.
** According to model.
Oil gauge* When the ignition is switched on, this indicates the oil level: The reading is only valid if the vehicle is on level ground and the engine has
been switched off for 10 minutes.
- needle in zone
C, the oil level is
correct,
- needle in zone D, check the oil level
using the dipstick and top up if nec-
essary.
Never exceed the maximum level onthe dipstick.
The oil level indicator switches off approximately 15 seconds after start-ing the engine.
Water in diesel filterwarning light(according to country) Risk of damage to the injection pump.
Contact a PEUGEOT dealer as soonas possible. Front brake pad wearwarning light*
For your safety, change the brake pads when thewarning light comes on.
Contact a PEUGEOT dealer.
DC
EF

96
YOUR 306 IN DETAILAnti-lock braking system (ABS) warninglight* It comes on for 3 seconds each time the ignition is
switched on. If it comes on at over 8 m.p.h. (12 km/h.) it indicates a malfunc-
tion of the ABS.
However, the vehicle retains con- ventional servo-assisted braking.
Contact a PEUGEOT dealer.
Oil level and temperature gauge* When the ignition is switched on, this indicates the oil level (see Oil Gaugesection). After approximately 15 seconds, the graduated section and the oil level
symbol go out. The oil temperature isthen shown.
- needle in zone
E, the temperature
is correct.
- needle in zone F, the temperature
is too high. To lower the oil temper- ature, reduce your speed.
Diesel pre-heat light If the light comes on, wait until it goes out before trying
the starter.
If the engine is warm enough, the lightwill not come on, and you can startthe engine without waiting. Front air bags*, sideair bags** anddisarming thepassenger air bag*
For operation, see section onAIR BAGS.
Side air bags** For operation, see
section on AIR BAGS.
* According to specification.
** According to model.
Oil gauge* When the ignition is switched on, this indicates the oil level: The reading is only valid if the vehicle is on level ground and the engine has
been switched off for 10 minutes.
- needle in zone
C, the oil level is
correct,
- needle in zone D, check the oil level
using the dipstick and top up if nec-
essary.
Never exceed the maximum level onthe dipstick.
The oil level indicator switches off approximately 15 seconds after start-ing the engine.
Water in diesel filterwarning light(according to country) Risk of damage to the injection pump.
Contact a PEUGEOT dealer as soonas possible. Front brake pad wearwarning light*
For your safety, change the brake pads when thewarning light comes on.
Contact a PEUGEOT dealer.
DC
EF

YOUR 306 IN DETAIL
Button Function
AT ATraffic information priority on/off.
B RDS RDS on/off.
Pressed for over 2 seconds: regional following mode on/off.
C BND/AST Waveband selection FMI, FMII, FMIII, AM.Pressed for over 2 seconds: autostore, automatic storing of stations.
D SRC Source selection; radio, cassette or CD*.
Pressed for over 2 seconds: CD* shuffle.
E Pressed fully: cassette fast rewind.
F Pressed fully:cassette fast fowards.
E + F Pressed half-way: reverses the direction of play of the cassette. Pressed fully: ejects the cassette.
G Increase the audio setting.
H Decrease the audio setting.
I AUDIO Selects bass, treble, loudness, balance and fader.
J Higher frequency automatic search. Selection of next CD* track.
K Lower frequency automatic search.Selection of previous CD* track.
L MAN Manual/automatic operation of button Jand K.
M Audio system on/off. Volume adjustment.
1 to 6 Selects a stored station. Pressed for over 2 seconds: stores a station.Selects a CD* disk.
jjj
kkk
jjjkkk


k
j
* Available as an accessory. 57

YOUR 306 IN DETAIL
58
GENERAL FUNCTIONS On / off
With the ignition key in the ACCESSORIES or IGNITION position, press the "ON/VOL"button to switch the set
on or off. ANTI-THEFT SYSTEM
The first time you use the set following disconnection of the set or the battery, you must enter the confidential code which was given to you on handover of your vehicle. Entering the code Switch the set on. The display shows "CODE"then the set changes over to code request mode and " - - - -" is displayed.
Enter your four-digitcode number using buttons " 1" to " 6".
For example: if your code is 5345 press buttons " 5", " 3", " 4" and " 5" in turn.
When the fourth number has been entered correctly, the radio starts automatically.
Error in entering the code
If an error is made when entering one of the first three digits, do not continue the operation and switch off the radio to prevent blocking it. Each incorrect code entry will result in the set being blocked for a period of from 5 seconds to 30 minutes, after
the 7th incorrect entry.
To unblock the set, leave it switched on during the waiting period. When " - - - -" is displayed, you can enter the
code again.
If the set is switched off during the waiting period, this waiting period will restart when the set is switched on again.After 14 incorrectly input codes, the radio will be permanently locked and the display will read ÒENDÓ.
ADJUSTING THE SOUND Adjusting the volume
Turn the "M"button to increase or decrease the volume of the set.
In the event of the radio overheating, the volume reduces. If an attempt is made to increase the volume the message " TOO HOT ÕÕ appears on the display.
Note If you have a telephone fitted with a Ò muteÓ signal output connected to the set, the set will automatically change
to Ò mute Ó when the telephone is used.

YOUR 306 IN DETAIL59
AUDIO SETTINGS Press the Ò AUDIOÒ button several times to select bass (BASS), treble (TREB) , loudness (LOUD), fader(FAD) and
balance (BAL).
Exit from audio mode is automatic after a few seconds, without pressing any button or by pressing the Ò AUDIOÓ
button after adjusting the balance. Note : bass and treble settings are speciflc to each source. It is possible to set them differently for radio,
cassette and CD.
Bass setting When Ò BASSÓ is displayed, press the Ò GÓ or Ò HÓ buttons to vary the setting.
ÑÒ BASS Ñ9 Ó for a minimum bass setting,
ÑÒ BASS 0 Ó for a normal position,
ÑÒ BASS +9 Ó for a maximum bass setting.
Treble settingWhen Ò TREBÓ is displayed, press the Ò GÓ or Ò HÓ buttons to vary the setting.
ÑÒ TREB Ñ9 Ó for a minimum treble setting,
ÑÒ TREB 0 Ó for a normal position,
ÑÒ TREB +9 Ó for a maximum treble setting.
Adjusting the loudness
This function automatically emphasises bass and treble tones when the volume is low. Press the ÒGÓor ÒHÓ buttons to switch this function on or off.
Setting the front/rear sound distribution (Fader) When Ò FA DÓ is displayed, press the Ò GÓ or Ò HÓ buttons to vary the setting.
The Ò GÓ button increases the volume at the front.
The Ò HÓ button increases the volume at the rear.
Note : For vehicles fitted with speakers at the front only, it is possible to cancel or add this function. This ope-
ration is carried out as follows:
- ignition key in Accessories position,
- with the radio switched off,- simultaneously pressing buttons ÒIÓand ÒMÓ.