key battery Peugeot 306 Break 2002 Owner's Manual

YOUR 306 IN DETAIL
58
GENERAL FUNCTIONS On / off
With the ignition key in the ACCESSORIES or IGNITION position, press the "ON/VOL"button to switch the set
on or off. ANTI-THEFT SYSTEM
The first time you use the set following disconnection of the set or the battery, you must enter the confidential code which was given to you on handover of your vehicle. Entering the code Switch the set on. The display shows "CODE"then the set changes over to code request mode and " - - - -" is displayed.
Enter your four-digitcode number using buttons " 1" to " 6".
For example: if your code is 5345 press buttons " 5", " 3", " 4" and " 5" in turn.
When the fourth number has been entered correctly, the radio starts automatically.
Error in entering the code
If an error is made when entering one of the first three digits, do not continue the operation and switch off the radio to prevent blocking it. Each incorrect code entry will result in the set being blocked for a period of from 5 seconds to 30 minutes, after
the 7th incorrect entry.
To unblock the set, leave it switched on during the waiting period. When " - - - -" is displayed, you can enter the
code again.
If the set is switched off during the waiting period, this waiting period will restart when the set is switched on again.After 14 incorrectly input codes, the radio will be permanently locked and the display will read ÒENDÓ.
ADJUSTING THE SOUND Adjusting the volume
Turn the "M"button to increase or decrease the volume of the set.
In the event of the radio overheating, the volume reduces. If an attempt is made to increase the volume the message " TOO HOT ÕÕ appears on the display.
Note If you have a telephone fitted with a Ò muteÓ signal output connected to the set, the set will automatically change
to Ò mute Ó when the telephone is used.

68
YOUR 306 IN DETAIL
GENERAL FUNCTIONS On / off
With the ignition key in the ACCESSORIES or IGNITION position, press the "M"button to switch the set on or off.
The set can operate for 30 minutes without switching the ignition on. ANTI-THEFT SYSTEM
The first time you use the set following disconnection of the set or the battery, you must enter the confidential code which was given to you on handover of your vehicle. Entering the code Switch the set on. The display shows " CODE IN" then the set changes over to code request mode and " - - - -" is displayed.
Enter your four-digitcode number using buttons " 1" to " 6".
For example: if your code is 5345 press buttons " 5", " 3", " 4" and " 5" in turn.
When the fourth number has been entered correctly, the radio starts automatically.
Error in entering the code
If an error is made when entering one of the first three digits, do not continue the operation and switch off the radio to prevent blocking it. Each incorrect code entry will result in the set being blocked for a period of from 5 seconds to 30 minutes, after
the 7th incorrect entry.
To unblock the set, leave it switched on during the waiting period. When " - - - -" is displayed, you can enter the
code again.
If the set is switched off during the waiting period, this waiting period will restart when the set is switched on again.After 14 incorrectly input codes, the radio will be permanently locked and will display ÒENDÓ.
ADJUSTING THE SOUND Adjusting the volume
Turn the "ON/VOL" button Mto increase or decrease the volume of the set.
In the event of the radio overheating, the volume level decreases. Note If you have a telephone fitted with a Ò muteÓ signal output connected to the set, the set will automatically change
to Ò mute Ó when the telephone is used.

THE REMOTE CONTROL
A single press on button Alocks the
doors and boot or tailgate, this is dis- played by the direction indicatorsstaying on for about 2 seconds.
A single press on button Bunlocks
the vehicle, this is displayed by the
direction indicators flashing rapidly.
YOUR 306 IN DETAIL
78
KEYS
Without central locking The key individually Iocks and unlocks the doors and boot or tailgate.
With central locking
Turning the key in the driverÕs door lock will lock or unlock the doors andboot or tailgate. If either of the frontdoors is not closed, the central lockingwill not work.
CHANGING THE REMOTE
CONTROL BATTERIES
To gain access to the battery, unclip the key casing with a coin where youcan see the ring (CR1620/3 volt battery). If the remote control does not work after the battery has been changed,re-programme the remote control. PROGRAMMING THE REMOTE CONTROL Manual synchronisation
- Switch off the ignition,
- Switch on the ignition,
- Immediately after switching on the
ignition press button A.
The remote control is now working again. Automatic synchronisation
- Switch on the ignition (position M),
- Switch off the ignition and, during the next four minutes, lock the vehicle using the remote control(button A).
The remote control is now workingagain.
Note: do not repeatedly press the
button of your remote control out of
range of your vehicle. You riskcausing it not to work and the remotecontrol would have to be repro-grammed.
A
B

SPECIAL FEATURES
124
DEADLOCKING* Deadlocking is an additional security device which means that the interior and exterior door controls cannot open the doors, when deadlocked. Deadlocking can be carried out in two ways:
- With the remote control.
- With the ignition key.
To operate deadlocking After locking the doors you have five seconds in which to operate the dead- locking. If using the remote control:
- press button
1once to lock your vehicle, the direction indicators stay on for
2 seconds.
- press button 1for a second time within the five seconds to deadlock your vehi-
cle, the direction indicators flash once.
- press button 2to unlock your vehicle, the direction indicators flash several times.
If using the ignition key, keep the key in the lock of one of the front doors, with the key turned towards the rear of the vehicle (turn the key towards the front to unlock).
To unlock the doors and boot or tailgate Place the ignition key in the lock of one of the front doors and turn ittowards the front of the vehicle.
Alternatively, press button 2on the
remote control.
* According to specification. Important After deadlocking, anybody inside
the car, and without the remotecontrol, will not be able to get out
by themselves. The doors canonly be unlocked by using theremote control, or the ignition keyin the door lock. If the battery is disconnected deadlocking remains activated. Itis still possible to open one of the
front doors using the ignition key,but the key will only open that par-
ticular door.
1
2

SPECIAL FEATURES
126
ALARM SYSTEM* Setting and disarming the alarm Switching off the siren The alarm completes the security equipment of your vehicle. It com-prises two types of protection: -exterior protection: when this is
set, the alarm sounds if a door,
the bonnet, the boot or the tail- gate are opened.
- interior sensor protection: when
it is set, the alarm sounds if thesensors detect a variation in the
air movement inside the vehicle(breaking of a window) or amovement inside the vehicle.
It is also equipped with an anti-
tamper function. If an attempt is made to neutralise the leads to the siren, the centralcontrol or the battery:
- the alarm is triggered,- the siren sounds, the headlights come on*. To set the alarm (exterior and interior protection) The ignition must be switched off.
You must be outside the vehiclePress the locking button of the remote control key (if your vehiclehas deadlocking, you then need topress this button again). The doors will lock.The direction indicators come on continuously for two seconds. The red lamp on the switch flashes once a second. Five seconds afterwards : the exteri- or protection is set. Fifty seconds afterwards : the interi- or protection is set. Note :
when the alarm is triggered,
the siren sounds for thirty seconds. It then stops, but the alarm remains set.
Warning
If, on setting the alarm, a door, the boot, tailgate or the bonnet are notproperly closed, the siren will be trig-
gered briefly. If the vehicle is proper-ly closed within forty five secondsafter this, the alarm is set, the direc-tion indicators come on continuouslyfor two seconds. In all cases the alarm is set forty five seconds afterwards. To disarm the alarm (exteriorand interior protection) Press the unlocking button on the remote control. The doors unlock.The direction indicators flash for two seconds. The red lamp on the switch goes out.Note :
if the lamp continues to flash
after disarming the alarm, it is
because it has been triggered. Thisflashing will stop on switching on theignition.
* According to specification.

SPECIAL FEATURES127
Emergency cut-off (Failure of the remote control)
Unlock the doors with the key.
Open the door.
The alarm is triggered. You then have ten seconds to stop it :
- Switch on the ignition.
- Immediately press the interior pro-
tection switch 1.
- The siren stops and the alarm is disarmed. Selecting the type of protection Locking without setting the alarm Special precautions
To set the alarm with exterior pro- tection only If, while you are away from the vehi- cle, you wish to leave a window par-tially open or a pet inside the vehicle,you should choose exterior protec-
tion only. In this case :
- Switch off the ignition.
- Press the interior protection switch
1until the lamp comes on continu-
ously.
- Get out of the vehicle.
- Press the locking button (or the deadlocking button if the vehicle is fitted with this) on the remote con-trol.
- The doors will lock.
- The direction indicators come on continuously for two seconds.
- The red lamp on the switch flashes once a second.
To disarm the alarm on exterior pro-
tection only. Press the unlocking button on the
remote control key. The doors unlock and the courtesy lights come on. The direction indicators flash for two seconds. The red lamp on the switch goes out. To lock the vehicle without setting the alarm It is the remote control which sets the alarm. Therefore,
if you wish to lock the
vehicle without setting the alarm,
use the key.
To charge or replace the battery :
- Switch on the ignition.
- Within ten seconds after switching on the ignition press the interior protection switch 1and keep it
pressed for two seconds.
- The indicator light flashes rapidly for three seconds.
- Switch off the ignition.
- You can then disconnect the bat- tery.
After reconnecting the battery :
- Lock, then unlock, the vehicle, using the remote control.
The alarm will be set the next time the vehicle is locked.
DO NOT M AKE ANY M ODIFICATIONS
TO THE ALARM SYSTEM .
1