fold seats PEUGEOT 5008 2014 Owners Manual

73
74
74
Familiarisation
18
Arranging your seats
Rigid panel
Putting the seats back in place
 Raise the seat back and push it rear wards until it locks.
From the boot
 Pull the strap B to release the seat and push the seat back for wards gently.
Folding the seats in
the 2nd row
 Pull the strap A upwards firmly to release the seat and continue to pull until the seat is fully folded.
Access to
the 3rd row seats
 Close the aircraft style tables on the 2 nd row seats if they are open.  Hold the control D up, the seat is released and the seat base rises to the seat back.  Push the seat back for wards, holding the control D forwards.
7 seat version
 After folding the seats, slide the catch C .

.
75, 127
75, 127
Familiarisation19
Arranging your seats (7 seat version)
 Pull the strap E and guide the seat until the assembly locks.  Fold the concertina boards forwards.
 Lower the head restraints and place the concertina board in the vertical position behind the seat.  While pulling the strap F , push the seat F , push the seat Fback for wards gently.  Remove the load space screen from its storage compartment and position it behind the 2 nd row seats.
 Place the rigid panels of the 2 nd row seats upright and lock them then fold the concertina boards rearwards.  Remove the load space cover and store it in its housing.
Changing from 7 to 5 seats Changing from 5 to 7 seats

Comfort
70
Table position, front passenger seat
This position, associated with that of the rear seats, allows you to transport long objects inside the vehicle. The maximum weight on the seat is 30 kg.
Folding the seat backrest
 Raise the armrest and fold up the "aircraft" style table, fixed on the back of the seat.  Check that no object, either on or underneath the seat, could hinder its movement.  To make the operation easier, place the head restraint in the low position (if the seat is in the fully for ward position).  If your vehicle is fitted with the video pack, place the protective cover on the head restraint.  Lift the control, located behind the seat, then guide the seat back for wards.
Returning the seat to the normal position
 Guide the seat backrest rear wards until it locks in place.
When the seat backrest is in this position, only the 2 nd row passenger seat located behind the driver can be used.

3
Comfort73
Flat floor
Each seat can be folded onto the floor to enable you to modify your vehicle’s interior space.
Folding the seat from the 2 nd row
 Place the seats as far towards the rear as possible.  Pull firmly upwards on strap C , to unlock the seat; keep pulling until the seat is fully folded.  Push the backrest slightly for wards so that the backrest pivots, folding onto the seat base. The assembly then lowers onto the f l o o r.
Folding the seat from the boot
When loading, for example, you can fold the seat or seats directly from the boot, once you have folded the 3 rd row seats (7 seat version).  Place the seats as far towards the rear as possible.  Pull on the strap D to release the chosen seat and push the backrest gently forwards.
Repositioning seat
 If necessary, return the 2 nd row seat rigid panels to their initial position and lock them.  Raise the backrest and push it rear wards until it locks.
Supervise any movement of seats by children.
Before moving the 3 rd row seats (7 seat version), return the 2 nd row seat rigid panels to their initial position and lock them. Emergency exit: if the first system (strap C ) fails, strap D enables the 3 rd row passengers to exit quickly. To avoid damaging the mechanism, the strap D unclips under excessive force. Simply reclip it to restore the system to working order.

Comfort
74
Rigid panel
Each 2 nd row seat backrest has a rigid panel attached. This panel enables you: - to have a continuous load sur face in the boot, whatever the positions of the seats, - to avoid having objects sliding under the 2 nd row seats. 30 kg maximum on each panel.
Releasing/Locking the rigid panel
 Before deploying the rigid panels, check that the 2 nd row seats are positioned as far towards the rear as possible.  Slide the latch E on the panel upwards, to
release it.  Return the panel to its initial position, then slide the latch E downwards, to lock it in place.
Entering/Exiting the 3 rd row
(7 seat version)
Repositioning the seat,
from the outside, with the
door open
If there are passengers seated in the 3 rd row (7 seat version):  Manually return the assembly as far as possible rear wards; the seat does not return as far as the maximum rear wards position so as to retain leg space for the 3 rd row passengers.  Fold the seat base.
 Raise the aircraft style table on the 2 nd row seat if it is down.  Hold the control F in the raised position, the seat unlocks and the seat base comes up against the backrest.  Push the seat backrest for wards, holding the control F forwards.

3
Comfort75
3 rd row seats (7 seat version)
Concertina boards
Two rigid concertina boards, which cannot be separated from the vehicle, cover the two 3 rd row seats, when these are in the folded position.
Folding the concertina boards
 Pull on the control, the 3 sections of the board will fold like a concertina. When the 3 rd row seats are upright, these concertina boards can be left either:
- flat behind the seats, - in the vertical position, thereby leaving a storage area available. The two rigid boards can each support a maximum of 100 kg.
Installing a seat
 Remove the load space screen.  If necessary, return the 2 nd row rigid panels to their initial position and lock them.  Correctly position the concertina board vertically behind the seat.  Pull on the control G , located behind the seat backrest. The backrest tilts rear wards
pulling the seat base with it. The seat locks in the open position.

Comfort
76
Storing a seat
 Lower the head restraints.  Correctly position the concertina board vertically behind the seat.  Pull on the control H , located at the bottom of the seat backrest. The seat is released.  Next push the backrest gently for wards. The backrest pivots folding onto the seat base. The seat base then folds into the stowage area provided for that purpose.  Reposition the concertina boards over the folded seats.
Before moving the 3 rd row seats, return the rigid panels of the 2 nd row seats to the upright position and lock them in place. Do not try to fold a 3 rd row seat that has
not first had the backrest fully locked in place. Do not leave objects either on or underneath the seat bases of the 3 rd row seats when you are folding them. Do not leave your hand on the control H as you fold the seats, as you risk trapping your fingers.

4
Access95
Tailgate release
Unlocking
 Fold back the rear seats to gain access to the lock from inside the boot.  Insert a small screwdriver into hole A of the lock to unlock the tailgate.  Move the latch to the left.
Locking after closing
If the fault persists after closing again, the boot will remain locked. System allowing the mechanical unlocking of the boot in the event of a battery or central locking system malfunction.

6
Fittings121

Storage compartments
under the rear footwells
Depending on the configuration, the vehicle has storage compartments under the footwells, located for ward of the outer rear seats. Access is via clipped flaps with a handle A .
"Aircraft" type tables
Installed on the back of each front seat, these allow you to set down objects.  To use the table, lower it fully until it locks in the low position.  To store the table, raise it, passing the point of resistance, to the high position.

Storage drawer
It is located under the driver's seat (manual adjustment).
Opening
 Raise the front of the drawer and pull it. Do not place heavy objects in the drawers. On the passenger side, do not forget to fold the "aircraft" type table before placing the seat in the table position. Do not place hard or heavy objects on the table. They could become dangerous projectiles in the event of emergency braking or impact.

Fittings
128
High load retaining net *
To use it in row 1:  fold the rear seats,  open the covers of the upper fixings 1 ,  unroll the high load retaining net,  position one of the ends of the net's metal bar in the corresponding upper fixing 1 , then do the same with the other end,  slacken the straps fully,  fix the snap hook of each of the straps on the corresponding Top Tether ring 3(located on the back of the folded rear side seats),  tighten the straps,  check that the net is hooked and tightened
c o r r e c t l y.
To use it in row 2:  roll up or remove the load space screen,  open the covers of the upper fixings 2 ,  unroll the high load retaining net,  position one of the ends of the net's metal bar in the corresponding upper fixing 2 , then do the same with the other end,  fix the snap hook of each of the straps in the corresponding stowing ring 4 ,  tighten the straps,  check that the net is hooked and tightened c o r r e c t l y.
Hooked onto the special upper and lower fixings, this permits use of the entire loading volume up to the roof: - behind the front seats (row 1) when the rear seats are folded. - behind the rear seats (row 2).
* If your vehicle is equipped with this.
When positioning the net, check that the strap loops are visible from the boot; this will make slackening or tightening easier.