headlamp Peugeot 508 RXH 2014 User Guide

145
508RXH_en_Chap05_visibilite_ed01-2014
Lighting left on audible signal
An audible signal when a front door
is opened warns the driver that the
vehicle's exterior lighting is on, with the
ignition off and in manual lighting mode.
In this case, switching off the lighting
stops the audible signal.
With the ignition off, if the dipped
headlamps remain on, the vehicle goes
into "
eC
O" mode to avoid discharging
the battery.
In some weather conditions (e.g. low
temperature or humidity), the presence
of misting on the internal sur face of the
glass of the headlamps and rear lamps
is normal; it disappears after the lamps
have been on for a few minutes. Daytime lighting, compulsory in certain
countries, which comes on automatically when
the engine is started making the vehicle more
visible to other road users.
Daytime running lamps
this function is assured:
-
i n countries where it is imposed by
regulations, by illumination of the dipped
beam headlamps with the sidelamps and
number plate lamps.
-

f
or other countries where it is provided, by
the use of dedicated lamps.
th

e lighting goes off when you switch
off the ignition, but you can always
switch it on again using the lighting
control stalk.
*

f

unction that can be set in the vehicle
configuration menu.
LED lamps
they come on when the engine is started.
Depending on the destination country, they are
used for:
-

d
aytime running lamps* in day mode and
sidelamps in night mode (they are brighter
when daytime running lamps),


or
-

s
idelamps in day and night mode.
Where L
eD l

amps are fitted, the filament bulbs
for the daytime running lamps / sidelamps in
the front lamp units are not used.
5
Visibility

146
508RXH_en_Chap05_visibilite_ed01-2014
Parking lamps
Side markers for the vehicle by illumination of
the sidelamps on the traffic side only.
F
W
ithin one minute of switching off the
ignition, operate the lighting control stalk
up or down depending on the traffic side
(for example: when parking on the left;
lighting control stalk upwards; the right
hand sidelamps are on).
th

is is confirmed by an audible signal and
illumination of the corresponding direction
indicator warning lamp in the instrument panel.
to s

witch off the parking lamps, return the
lighting control stalk to the middle position or
switch on the ignition.
tem

porarily keeping the dipped beam
headlamps on after the ignition has been
switched off makes the driver's exit easier
when the light is poor.
Manual guide-me-home
lighting
Switching on
F Within 30 seconds or a minute after switching of the ignition (according to the
lighting duration programmed in the main
menu of the instrument panel), "flash" the
headlamps using the lighting stalk.
F

A f
urther "headlamp flash" switches the
function off.
Switching off
the manual guide-me-home lighting switches
off automatically after about 30 seconds.
Programming
the duration of the guide-me-
home lighting is is set in the Main
menu of instrument panel screen.
Select " Vehicle parameters " then
" Lighting ", then change the lighting
duration.
Visibility

147
508RXH_en_Chap05_visibilite_ed01-2014
the sidelamps and dipped beam headlamps are
switched on automatically, without any action on
the part of the driver, when a low level of external
light is detected or in certain cases of activation of
the windscreen wipers.
As soon as the brightness returns to a sufficient
level or after the windscreen wipers are switched
off, the lamps are switched off automatically.
Automatic illumination of
headlamps
Activation
F turn the ring to the "AUTO" position. th e automatic
illumination of headlamps is accompanied by a
message in the instrument panel screen.
Deactivation
F turn the ring to another position. Deactivation is accompanied by a message
in the instrument panel screen.
Association with automatic
guide-me-home lighting
Association with automatic illumination of
headlamps provides the guide-me-home
lighting with the following additional options:
-

s
election of the lighting duration of 15, 30
or 60 seconds,
-

a
utomatic activation of guide-me-home
lighting when the automatic illumination of
headlamps is in operation.
Operating fault
In the event of a fault with the
sunshine sensor, the lighting
comes on, this warning
lamp is displayed in the instrument panel and/
or a message appears in the instrument panel
screen, accompanied by an audible signal.
Contact a P
e

uge
Ot
dealer or a qualified
workshop.
In fog or snow, the sunshine sensor
may detect sufficient light. In this
case, the lighting will not come on
automatically.
Do not cover the sunshine sensor,
coupled with the rain sensor and
located in the centre of the windscreen
behind the rear view mirror; the
associated functions would no longer
be controlled.
5
Visibility

148
508RXH_en_Chap05_visibilite_ed01-2014
Adaptive lighting
Switching on
the driver can take over at any time, if the
circumstances dictate:
System which automatically changes between
dipped and main beam according to the driving
conditions, using a sensor in the rear view
m i r r o r.
th

e system is active from 15 mph (25 km/h)
and is deactivated below 9 mph (15 km/h).
F

P

ut the lighting control stalk on the "A
u

t
O

"
or "Dipped/main beam headlamps"
position.
Switching off
Flashing the headlamps does not
deactivate the system.
th

e state of the system is stored in
memory when switching off the ignition.
th

is automatic headlamp dipping
system is a driving aid.
t
h
e driver
remains responsible for the vehicle's
lighting and its correct use for the
prevailing conditions of light, visibility
and traffic.
the
system may suffer interference or
not work correctly:
-
u
nder conditions of poor visibility
(for example, snowfall, heavy rain
or thick fog, ...),
-
i
f the windscreen is dirty, misted or
obscured (by a sticker, ...) in front of
the sensor,
-
i
f the vehicle is facing highly
reflective signs.
th
e system is not able to detect:
-
r
oad users that do not have their
own lighting, such as pedestrians,
-
r
oad users whose lighting is
obscured, such as vehicles running
behind a safety barrier (on a
motorway, for example),
-

r
oad users at the top or bottom of
a steep slope, on twisty roads, on
crossroads.
F

P
ress this button, the
indicator lamp goes off,
or
F
D
ipping the headlamps
manually using the lighting
control stalk, whether in the
"A
u
t
O
" or "Dipped/main
beam headlamps" position.
F

P

ress this button, the
indicator lamp comes on.
Visibility

149
508RXH_en_Chap05_visibilite_ed01-2014
exterior welcome
lighting
Switching on
Switching off
the exterior welcome lighting switches off
automatically after a set time, when the ignition
is switched on or on locking the vehicle.
Programming
the activation/deactivation and
lighting duration are set in the Main
menu of instrument panel screen.
Select " Vehicle parameters " then
" Lighting ", then change the lighting
duration. F
P
ress the open padlock on the
remote control.
th
e dipped beam headlamps and the
sidelamps come on; your vehicle is
also unlocked.
Door mirror spotlamps
Switching on
the spotlamps come on:
- w hen you unlock the vehicle,
-

w
hen you remove the key from the ignition,
-

w
hen you open a door,
-

w
hen you use the remote control.
Switching off
they are timed to go off automatically.
to m

ake your approach to the vehicle easier,
these illuminate:
-

t

he zones facing the driver’s and
passenger’s doors,
-

t

he zones for ward of the door mirrors and
rear ward of the front doors.
Remote switching on of the lighting makes your
approach to the vehicle easier in poor light. It is
activated according to the level of light detected
by the sunshine sensor.
5
Visibility

150
508RXH_en_Chap05_visibilite_ed01-2014
Manual adjustment
of halogen
headlampsAutomatic adjustment of "full LeD
"
technology headlamps
to avoid causing a nuisance to other road
users, the beams of the halogen headlamps
should be adjusted according to the load in the
vehicle.
If a fault occurs, this
warning lamp is displayed
in the instrument panel,
accompanied by an audible signal and a
message in the instrument panel screen.
th

e system then places your headlamps in the
lowest position. In order to avoid causing a nuisance to other
road users, this system corrects the height of
the "full L
e
D
" headlamps beam automatically,
in relation to the load in the vehicle. If a fault occurs, do not touch the "full
L
eD

" bulbs. Contact a P
e
uge
Ot

dealer or a qualified workshop.
th

e initial setting is position "0" .
1

D
river
2

D
river + front passenger.
3

D
river + front passenger + rear
passengers.
4

5
people.
5

5 p
eople + a load in the boot.
6

D
river + a load in the boot.
Travelling abroad
the design of the dipped beam
headlamps allows, without modification,
driving in a country that drives on the
other side of the road to the country in
which your vehicle was sold.
Visibility

151
508RXH_en_Chap05_visibilite_ed01-2014
With dipped or main beam on, this system uses
LeDs (light-emitting diodes) to illuminate the
inside of a bend.
th

e speed of the vehicle must be below
75 mph (120 km/h).
th

is function is a available only with "full-L
eD
"
headlamps.
Additional headlamps
Operation
this system operates from a certain angle of
rotation of the steering wheel.
System inactive
the system does not operate:
- b elow a certain angle of rotation of the
steering wheel,
-

a
bove 75 mph (120 km/h),
-
w

hen reverse gear is engaged.
5
Visibility

153
508RXH_en_Chap05_visibilite_ed01-2014
Rear wiper
If a significant accumulation of snow or
ice is present, or when using a bicycle
carrier on the boot, deactivate the
automatic rear wiper via the instrument
panel screen configuration menu.
Rear wiper selection ring: park,
intermittent wipe,
wash-wipe (set duration).
Reverse gear
When reverse gear is engaged, the rear wiper
will come into operation if the windscreen
wipers are operating.
th

e function is activated or
deactivated via the instrument panel
screen configuration menu.
th

is function is activated by default.
Programming
F Pull the windscreen wiper stalk towards you for a few seconds. th e windscreen
wash then the windscreen wipers operate
for a fixed period.
the

headlamp washers only operate when
the dipped beam headlamps are on and the
vehicle is moving.
Windscreen and headlamp
wash
Screenwash/headlamp wash
level low
In the case of vehicles fitted
with headlamp washers,
when the fluid reservoir low
level is reached this warning lamp comes on in the
instrument panel, accompanied by an audible signal
and a message in the instrument panel screen.
th

e warning lamp comes on when the ignition is
switched on, or every time the stalk is operated, until
the reservoir is refilled.
Next time you stop, refill the screenwash / headlamp
wash reservoir.
5
Visibility

199
508RXH_en_Chap08_info-pratiques_ed01-2014
Changing a bulb
Front lamps
Model with "full LED" technology
headlamps
1. Additional lighting.
2. Dipped beam headlamps.
3.
M

ain beam headlamps.
4.
D

aytime running lamps / sidelamps.
5.
D

irection indicators.
Model with halogen headlamps
1. Dipped beam headlamps (H7-55W).
2. M ain beam headlamps (H7-55W).
3.
D

aytime running lamps / sidelamps
(LEDs).
4.
D

irection indicators (LEDs).
In some weather conditions (e.g. low
temperature or humidity), the presence
of misting on the internal sur face of the
glass of the headlamps and rear lamps
is normal; it disappears after the lamps
have been on for a few minutes. Before doing any work on your vehicle,
switch off the ignition (
Ready lamp off)
to avoid any risk of injury resulting from
automatic operation of the engine.
For the replacement of these light-
emitting diode (L
eD

) lamps, contact
a P
e

uge
Ot

dealer or a qualified
workshop.
All of these lamps use light-emitting diodes-
L
e

Ds. For H7 type bulbs with lugs, take care to
observe their correct installation so as to
ensure the best lighting performance.
8
Practical information

200
508RXH_en_Chap08_info-pratiques_ed01-2014
Main beam headlamps
Dipped beam headlamp
th

e headlamps are fitted with
polycarbonate glass with a protective
coating:
F

d

o not clean them using a dr y
or abrasive cloth, nor with a
detergent or solvent product,
F

u

se a sponge and soapy water or a
pH neutral product,
F

w

hen using a high pressure washer
on persistent marks, do not keep
the lance directed towards the
lamps or their edges for too long,
so as not to damage their protective
coating and seals.
Changing a bulb should only be done
after the headlamp has been switched
off for several minutes (risk of serious
burns).
F

D

o not touch the bulb directly with
your fingers, use a lint-free cloth.
It is imperative to use only anti-
ultraviolet (
uV

) type bulbs to avoid
damaging the headlamp.
Always replace a failed bulb with a
new bulb with the same type and
specification.
Halogen model
F Remove the protective plastic cover by pulling on the tab.
F
u
n
clip the bulb connector.
F
e
x
tract the bulb by pulling and change it. F
R emove the protective plastic cover by
pulling on the tab.
F
u
n
clip the bulb connector.
F

Remove the bulb by pulling it out and change it.
For reassembly, carry out these operations in
reverse order.For reassembly, carry out these operations in
reverse order.
For the left hand headlamp, it is
necessary to remove the battery.
Refer to the corresponding section.
Practical information