lights Peugeot 807 2013 User Guide

Instruments and controls

36


Zero re-set

Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:


- Switch off the ignition,

- Press and hold the trip recorder re-set
button,

- Switch on the ignition.
The display begins a countdown.
When the display shows "= 0 ", release
the button; the spanner disappears.

Engine oil level indicator

When the ignition is switched on, the
engine oil level is indicated for a few
seconds, after the service information.
Oil level correct

Lack of oil
Flashing of "OIL"
,
linked with the
service warning light,
accompanied by an
audible signal and a message on the
display, indicates a lack of oil which
could damage the engine.
If the lack of oil is confi rmed by a check
using the dipstick, it is essential that
the level is topped up.

Oil level gauge fault
Flashing of "OIL --"

indicates a
malfunction of the
engine oil level
gauge. Consult a PEUGEOT dealer.
Dipstick

A
= maximum, never exceed
this level as a surplus of oil
may damage the engine.
Contact a PEUGEOT dealer
without delay.

B
= minimum, top up the level
via the oil fi ller cap, using
the type of oil suited to your
engine.



Trip recorder zero
reset button
With the ignition on, press
the button until the zeros
appear.


Lighting rheostat

With the lights on, press
the button to vary the
intensity of the lighting
of the instruments and
controls. When the lighting reaches
the minimum (or maximum) setting,
release the button then press it again
to increase (or reduce) the brightness.
As soon as the lighting is of the
required brightness, release the button. The level read will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes. After this operation, if you wish to
disconnect the battery, lock the
vehicle and wait for at least fi ve
minutes, otherwise the zero re-set will
not be registered.

Steering wheel controls

EASE OF USE and COMFORT
3
43

Automatic lights
If your vehicle is fi tted
with a brightness
sensor. Lights off
Dipped beam (green)
Main beam (blue)


DIRECTION INDICATORS
(green flashing) STEERING MOUNTED CONTROLS
Checking by means of the
indicator lights on the instrument
panel is described in the
"Instruments and controls" section of
chapter 2. Side lights


LIGHTING CONTROL


Left
: downwards.

Right
: upwards.
Front and rear lights
Selection is by turning ring A
.

Steering mounted controls

44

Front fog lights (green)
and rear fog lights
(amber, 2nd rotation of
the ring forwards). To switch off the front and rear
fog lights, turn the ring rearwards
twice in succession.

Front and rear fog lights
Rotate ring B
forwards to switch on
and rearwards to switch off. The
status is confi rmed by the light on the
instrument panel.
These operate with the side lights and
the dipped beam headlamps. In clear weather or in rain, both
day and night, rear fog lights
dazzle and are prohibited.
Do not forget to switch them off when
they are no longer needed.
Automatic switching on of the lights
switches off the rear fog lamps, but the
front fog lamps remain on.



Daytime running lamps

Depending on the country in which
the vehicle is sold, the vehicle may be
equipped with daytime running lamps.
The dipped headlamps come on when
the vehicle is started.
The instruments and controls
(instrument panel, screen, air
conditioning control panel, ...) are
only illuminated on switching to the
automatic illumination of headlamps
mode or when the lamps are switched
on manually.




Dipped beam/main beam change
Pull the stalk fully towards you.
Front fog lights (green,
1st rotation of the ring
forwards).
Lights-on buzzer
When the ignition is switched off, when
the driver's door is opened, a buzzer
sounds if you have left your lights on. This warning lamp comes on
in the instrument panel.

Steering wheel controls

EASE OF USE and COMFORT
3
45


Automatic "Follow-Me-Home"
lighting
With the ignition off, when you leave
your vehicle with the automatic
switching on of the lights function
activated
, the side lights and dipped
headlamps remain on for the selected
duration.
To deactivate or activate this
function, go to the display
confi guration menu.
The duration of the timed period must
also be set (15, 30, 60 seconds), via
the display confi guration menu.
Carry out these operations when the
vehicle is stationary.
HEADLAMPS BEAM
Depending on the load in your vehicle,
the beam setting must be adjusted.

0
- 1 or 2 people in the front seats.

1
- 5 people.

2
- 6 to 8 people.

3
- Driver + maximum authorised
loads.

Initial setting is position 0.
In foggy weather or in snow,
the brightness sensor can
detect suffi cient light. As a
consequence, the lights will not come
on automatically.

Automatic switching on of the lights

Deactivation
Turn the ring forwards or rearwards.
The deactivation of this function is
accompanied by a message on the
display.
The function is deactivated temporarily
when you use the manual lights stalk.

If the brightness sensor does not
function correctly
, the lights come on
accompanied by the service warning
light, an audible signal and a message
on the display.
Contact a PEUGEOT dealer.

Do not cover the brightness
sensor located in the centre of the
fascia. It is used for the automatic
switching on of the lights and for the
automatic wipers.



Activation
Turn the ring to the AUTO
position.
The activation of this function is
accompanied by a message on the
display.

AUTOMATIC ADJUSTMENT OF
THE XENON HEADLAMPS

On vehicles which are fi tted with xenon
headlamps, this system automatically
corrects the height of the light beam,
regardless of the load in the vehicle.
The driver is then guaranteed optimum
lighting without dazzling other road
users.
Cancelling:
- "fl ash" the headlamps,

-
get out of the vehicle and lock it.
If your vehicle is fi tted
with a brightness
sensor, the side lights
and dipped beam
headlamps switch on
automatically if the
light is poor, or during operation of the
windscreen wipers. They switch off
as soon as the light becomes bright
enough or the windscreen wipers stop.
This function is not compatible with the
daytime lights.

80


Practical information

Front courtesy light


Automatic switching on/off

The front courtesy light comes on
when the key is removed from the
ignition, when the vehicle is unlocked,
when one of the front doors is opened
or for location of the vehicle using the
remote control.
It switches off gradually after the
ignition is switched on and when the
vehicle is locked. Permanently on, ignition on.
Front: comes on when one
of the front or rear doors is
opened.
Permanently off. Individual reading light


Rear courtesy light rows 2 and 3

These are switched on and off by
means of a manual switch.

COURTESY LIGHTS

Rows 2 and 3: comes on
when one of the rear doors is
opened. Rear courtesy light

86


Driving safely

HANDBRAKE

HAZARD WARNING LIGHTS

Press the button, the direction
indicators fl ash.
They can operate with the ignition off.


Automatic lighting of hazard
warning lights
Equipment conditioned according
to country: when braking in an
emergency, depending on the
deceleration, the hazard warning lights
come on automatically. They switch
off automatically the fi rst time you
accelerate.
It is also possible to switch them off by
pressing the button.

DRIVING SAFELY


Applying
When parking, pull the handbrake to
immobilize your vehicle.When parking
on a slope, direct your wheels towards
the pavement and pull the handbrake.

Releasing
Pull on the handle and press the button
to release the handbrake. Pull the button located at the end of the
handbrake forwards.
The handbrake lever lowers.
You can now pivot the seat.
To return to normal operation, pull the
lever upwards until a click is heard.
If the handbrake is still on or has
not been released properly, this is
indicated by:

Disengaging
If your vehicle is fi tted with a version
with a rotating front seat, apply the
handbrake. a warning light which comes
on on the instrument panel,
an audible signal,
a message on the display.

96
Airbags

Disarming
The passenger's front air bag alone
can be disarmed:




- With
the
ignition
switched
off
,
insert the key into the passenger air
bag disarming switch,

- turn it to the "OFF"
position,
-


then remove the key keeping the
slot in this position.

Front air bags

The front air bags are incorporated in
the centre of the steering wheel for the
driver and in the fascia for the front
passenger.

Front air bag fault
Reactivation
In the "OFF"
position, the passenger
air bag will not be triggered in the
event of an impact.
As soon as the child seat is removed,
turn the air bag slot to the "ON"

position to re-activate the air bag
and thus ensure the safety of your
passenger in the event of an impact. To ensure the safety of your
child, it is essential to disarm the
passenger air bag when you install
a rear-facing child seat on the front
passenger seat. Otherwise, the child
would risk being killed or seriously
injured if the air bag were to infl ate.
The air bag warning light
on the instrument panel is
lit throughout the period of
disarming.
If the two air bag warning lights
are lit continuously, do not install
a rear-facing child seat. Consult a
PEUGEOT dealer.

Activation
They are deployed simultaneously,
unless the passenger's front air bag
has been disarmed, in the event of a
serious front impact applied to all or
part of the front impact zone A
in the
longitudinal centreline of the vehicle
on a horizontal plane directed from the
front towards the rear of the vehicle.
The front air bag infl ates between
the front occupant of the vehicle and
the fascia to cushion his forward
movement. If this warning light comes on,
accompanied by an audible
signal and a message on the
display, consult a PEUGEOT
dealer to have the system
checked.

11 3


Levels

CHECKS
6

These regular maintenance
operations will keep your vehicle
in good running order. Consult the
instructions at PEUGEOT dealerships
or in the servicing booklet enclosed in
the handbook pack. To maintain the reliability of engines
and emission control systems, the use
of additives in engine oil is prohibited.



Oil change

It is imperative that this is carried out at
the intervals specifi ed and the viscosity
grade of the oil selected must fulfi l the
requirements in accordance with the
manufacturer’s servicing schedule.
Consult the instructions at PEUGEOT
dealerships.
Remove the dipstick before fi lling.
Check the level after fi lling (never
exceed the max mark).
Screw the cap back onto the sump
before closing the bonnet.
LEVELS

If you have to remove/refi t the
engine style cover, handle it with
care to avoid damaging the fi xing
clips.

Dipstick


Warning lights
Oil level

Check the level regularly and top up
between changes. The maximum
consumption is 0.5 litre per 600 miles
(1 000 km).
Check the level with the vehicle level,
engine cold, using the dipstick.

Viscosity selection
In all cases, the oil selected must meet
the manufacturer’s requirements.

Checking by means of the
warning lights on the instrument
panel is described in chapter 2,
"Instruments and controls" section.


Changing the brake fluid

The brake fl uid must be changed at
the intervals stated, according to the
manufacturer’s servicing schedule.
Use fl uids recommended by
the manufacturer, which fulfi l
DOT4 standards.
The level must be between the MIN
and MAX marks on the reservoir.
If fl uid has to be added frequently,
this indicates a failure which must be
checked by a PEUGEOT dealer as
soon as possible.
There are two marks
on the dipstick:

A
= maximum
If you fi ll past this
mark, contact a
PEUGEOT dealer.

B
= minimum
Never allow the level
to fall below this
mark.

11 6


Battery


ECONOMY MODE FUNCTION

After the engine has stopped, with
the key in the ignition position, certain
functions (windscreen wiper, electric
windows, courtesy lights, audio
equipment, etc.) can only be used for a
cumulative duration of thirty minutes, to
prevent discharging the battery.
Once the thirty minutes are over, the
message "Economy mode active"

appears on the display and the active
functions are put on standby.
To resume the use of these functions
immediately, start the engine and let it
run for a few seconds.
A fl at battery will prevent the engine
from starting.

To charge the battery using a
battery charger


- disconnect the battery,

- follow the instructions for use
given by the battery charger
manufacturer,

- reconnect starting with the negative
(-) terminal,

- check that the terminals and
connectors are clean. If they are
covered with sulphate (white or
greenish deposit), disconnect them
and clean them.

TERY
BATT

This is housed in a compartment
located underneath the fl oor, in front of
the driver's seat.
Before disconnecting the battery, you
must wait for 2 minutes after switching
off the ignition.
Never disconnect a terminal when the
engine is running.
Never charge a battery without fi rst
disconnecting the terminals.
Close the sunroof and the windows
before disconnecting the battery. If
they do not operate normally following
reconnection of the battery, they must
be reinitialised.
It is advisable to disconnect the
battery if the vehicle is not to be used
for a period of more than one month.
After every reconnection of the battery,
switch on the ignition and wait 1 minute
before starting to allow the electronic
systems to be initialised. If slight
diffi culties are experienced after this,
please contact a PEUGEOT dealer.
The door open monitoring electrical
system consumes power, remember
to close the sliding doors when your
vehicle is parked for long periods.


To start the vehicle from
another battery


- connect the red cable to the
positive (+) terminals of the two
batteries,

- connect one end of the green or
black cable to the negative (-)
terminal of the slave battery,

- connect the other end of the green
or black cable to an earth point on
the broken down vehicle as far as
possible from the battery,

- operate the starter, let the engine run,


- wait for the engine to return to idle,
then disconnect the cables. For the sunroofs safety auto-
reverse, refer to the "Accesses"
section of chapter 2. For the electric windows safety
auto-reverse, refer to the "Mirrors
and windows" section of chapter 3.

121
QUICK HELP
7


Changing a bulb


CHANGING A BULB


Handle the bulbs with a dry cloth.
Make access easier on the right-hand
side by removing the wash-wipe pipe
and the fuse box cover.
High pressure washing: when using
this type of washing on stubborn dirt,
do not persist on the headlamps, the
lights and their surrounds to avoid
damaging their coating and their seal.
2 - Main beam headlamps
H7-55 W or xenon bulb.



- Turn the protective cover
corresponding to the faulty bulb
a quarter of a turn to the left and
remove it.

- Disconnect the connector.

- Press the end of the securing clip
to free it. Change the bulb.
When fi tting the new bulb, ensure that
the direction notches are positioned
correctly and the securing clip is fi xed
properly.


- Reconnect the connector.

- Refi t the protective cover, then turn
it a quarter of a turn to the right.

3 - Fog lamps
H1-55 3W.


FRONT LIGHTS



1.
Dipped headlamps


2.
Main beam headlamps


3.
Fog lamps


4.
Side lights


5.
Direction indicators


1 - Dipped beam headlamps
H7-55 W or xenon bulb.

4 - Side lights
W 5 W.


- Push the light from the inside
towards the outside of the bumper.

- Pull the light forwards.

- Turn the bulb holder a quarter of a
turn to the left and remove it.

- Turn the bulb a quarter of a turn to
the left, remove it and change it.
When refi tting, engage the light
towards the outside and move it
towards the inside of the bumper.



WARNING: RISK OF
ELECTROCUTION

Xenon bulbs must be changed by a
PEUGEOT dealer.