ignition Peugeot iOn 2018 User Guide

23
Always remove the key from the ignition
when leaving the vehicle, even for a short
time.
In the event of contact during operation of
the electric windows, you must reverse the
movement of the window. To do this, press
the corresponding control.
When operating the passenger electric
window switches, the driver must ensure
that no-one is preventing correct closing
of the windows.
The driver must ensure that the
passengers use the electric windows
c o r r e c t l y.
Be aware of children when operating the
windows.
Charging flaps
Normal charging
F Pull control A in the lower part of the dashboard, driver's side, to unlock the
access flap.
F

O
pen the access flap on the right-hand
side of the vehicle.
F

P
ress on latch B to open the socket cover.
Fast charging
(Depending on equipment.) F
P
ull control C under the driver's seat, near
the door, to unlock the access flap.
F
O
pen the access flap on the left-hand side
of the vehicle.
F
P
ress on latch D to open the socket cover.
For more information on Recharging the
main battery , refer to the corresponding
section.
2
Access

30
Recommendations for ventilation and air conditioning
In order for these systems to be fully effective,
follow the operation and maintenance
guidelines below:
F
I
f after an extended stop in sunshine,
the interior temperature is very high, first
ventilate the passenger compartment for a
few moments by opening the windows.
Put the air flow control at a setting high
enough to quickly change the air in the
passenger compartment.
F

T
he condensation created by the air
conditioning results in a discharge of
water under the vehicle which is per fectly
normal.
F

T
o ensure that the air is distributed evenly,
keep the external air intake grilles at the
base of the windscreen, the nozzles, the
vents, the air outlets and the air extractor
in the boot free from obstructions.
F

I
n normal conditions, use the intake
of exterior air as prolonged use of air
recirculation may cause misting of the
windscreen and side windows.
F

O
perate the air conditioning system for 5
to 10
minutes, once or twice a month to
keep it in good working order. The heating and air conditioning operate
using the energy supplied by the main
battery. Their use increases the vehicle's
consumption of electrical energy and
reduces its range.
Remember to switch off the heating or
air conditioning as soon as you judge it
to no longer be necessary.
Ventilation, heating, and air conditioning
can be activated during normal charging
of the vehicle when the ignition is set to
the ACC position.
During fast charging of the vehicle,
ventilation, heating, and air conditioning
cannot be activated.
F
E nsure that the passenger compartment
filter is in good condition and have the
filter elements replaced regularly.
F

T
o ensure correct operation of the air
conditioning system, you are also advised
to have it checked regularly.
F

I
f the system does not produce cold air,
do not use it and contact a PEUGEOT
dealer or a qualified workshop.
Ease of use and comfort

36
If the charge start is programmed without
programming the charge duration, the
battery will be charged fully.
Charge duration
programming
This function is used to set the charging time
for your vehicle.
Switch on the remote control.
Press the MODE button to select the charge
duration programming.This symbol is displayed on the
screen.
Use the arrows to adjust the charging time:
each press adjusts the time in half-hourly
intervals.
Press the on/off button briefly to send the data
to the vehicle.
The charge duration can be programmed
for between 0.5 and 19.5
hours. However,
you can also select the duration "-h": in
this case, charging will stop when the
battery is fully charged. This duration is
the value entered by default. If the charge duration is programmed
without programming the start time, the
battery will be charged immediately for
a duration corresponding to the one
programmed.
Cancelling programmings
With the remote control
Press the charge immediately
button, then press the on/off button
briefly to send the data to the
vehicle.
With the switch
Turn the vehicle's ignition switch to the ON

position then turn it to LOCK .
Any programming carried out with remote
control is cancelled automatically every
time the vehicle is started.
Thermal comfort
programming
This function is used to programme the running
of the:
-

heating,
-
a

ir conditioning,
-


demisting.To programme the heating, air
conditioning or demisting functions, the
following conditions must be met.
-

T
he drive selector is in position P .
-

T
he ignition switch is on LOCK .
-

T
he vehicle is connected with the
normal recharging cable.
-

A
ll the doors are closed properly.
-

T
he battery is sufficiently charged (one
bar minimum).
For maximum efficiency in programming
the thermal comfort, make sure that all the
vehicle's windows are closed.
Ease of use and comfort

38
Malfunctions
Remote control
Warning/
indicator lampStateCausesAction/Observations
Flashes within approximately ten seconds
after switching on the remote control. There is a malfunction.
Switch the remote control off and then on
again.
Flash within approximately one second
after switching on the remote control. Electrical interference is preventing the
remote control or data transmission from
operating.Move away from the inter ference sources.
Flash within approximately ten seconds
after switching on the remote control. The aerial is not extended.
Extend the aerial.
You are outside the range of the remote
control. Move nearer to the vehicle.
The ignition switch is not in the LOCK
position. Turn the switch to LOCK
.
Ease of use and comfort

41
Front and rear foglamps
Foglamps selection ring.
They operate with the sidelamps and dipped or
main beam headlamps.Front and rear foglamps:
F

T
urn the ring for wards once to switch on the
front foglamps.
F

T
urn the ring for wards twice to switch on the
rear foglamp.
F

T
urn the ring backwards once to switch off
the rear foglamp.
F

T
urn the ring backwards twice to switch off
the front foglamps. It is prohibited to switch on the front or
rear foglamps in fine weather or in rain,
night or day. In these situations, the power
of their beams may dazzle other drivers.
Do not forget to switch off the front
foglamps and the rear foglamp when they
are no longer necessary.
When lighting is left on
When the driver's door is opened, with the
ignition off, an audible signal warns the
driver that the vehicle's lighting is left on.
In this case, switching off the lighting
stops the audible signal.
Direction indicators
(flashing)The ring automatically returns to its initial
position.
The rear foglamp switches off automatically
when you switch off the sidelamps and dipped
or main beam headlamps.
F

L
eft: lower the lighting control stalk passing
the point of resistance.
F

R
ight: raise the lighting control stalk passing
the point of resistance.
Daytime running lamps
Specific daytime lighting to make the vehicle
more visible.
The daytime running lamps light up
automatically when the engine starts if no other
lamps are on.
They cannot be deactivated.
Although these lamps are located in the
same lamp unit as the front foglamps, they
operate with a specific bulb.
Their use complies with the Highway
Code.
4
Lighting and visibility

42
Automatic illumination/
switching off of the headlamps
Automatic illumination
When the lighting control stalk ring is in
the AUTO position, the sidelamps and
dipped beam headlamps are switched on
automatically, without any action on the part of
the driver, when a low level of ambient light is
detected.
As soon as the level of light becomes sufficient
again, the lights are switched off automatically.
The sensor is located at the bottom of the
windscreen.
Do not cover the sunshine sensor, as the
associated functions would no longer be
controlled.
In fog or snow, the sunshine sensor may
detect sufficient light. The headlamps may
not come on automatically.
Automatic switching off
When the lighting control stalk is in the "AUTO"
position, if the ignition key is in the "LOCK" or
"ACC" position or is removed, the headlamps
will automatically switch off when the driver's
door is opened .
Headlamp beam height
adjustment
To avoid causing a nuisance to other road
users, the height of the halogen headlamp
beams must be adjusted according to the load
in the vehicle.
0.Driver only or driver + 1 front
passenger.
1 or 2. 4 passengers (including driver).
3. 4 passengers (including driver) +
maximum authorised load.
4. Driver + maximum authorised load.
The initial setting is position " 0".
Wiper control stalk
The wipers are controlled directly by the driver
using control A and ring B .
In wintry conditions, remove snow, ice
or frost present on the windscreen,
around the wiper arms and blades and
the windscreen seal before operating the
wipers.
Do not operate the wipers on a dry
windscreen. Under extremely hot or cold
conditions, ensure that the wiper blades
are not stuck to the windscreen before
operating the wipers.
Lighting and visibility

46
Hazard warning lamps
F When you press this red button, all four direction indicators flash.
They can operate with the ignition off.
Brake lamps, automatic
operation
The brake lamps may light up automatically
when you release the accelerator pedal.
Their illumination is not systematic and
depends on the rate of deceleration.
Horn for pedestrians
(Depending on equipment.)
System to alert pedestrians to the presence of
the vehicle.
When the vehicle is started, illumination of
the button indicator lamp for a few seconds
indicates system activation.
Operation
Horn
F Press the central part of the steering wheel. The horn sounds when the vehicle speed is
between 0 and 22
mph (35 km/h),
Deactivation
In certain driving conditions you can deactivate
the system.
Press this button.
The button indicator lamp comes on and the
audible signal stops.
Another press reactivates the system.
The button indicator lamp goes off. Before deactivating the system, make
sure that you are not driving in an area
frequented by pedestrians.
The system is reactivated automatically at
every new start.
Malfunction
The button indicator lamp flashes if the system
malfunctions. Contact a PEUGEOT dealer
or a qualified workshop to have the system
checked.
Safety

47
Emergency or assistance
call
Peugeot Connect SOS
* In accordance with the general conditions of use for the ser vice available from dealers
and subject to technological and technical
limitations.
**

A
s per the geographic coverage of
"Peugeot Connect SOS", "Peugeot Connect
Assistance" and the official national
language chosen by the owner of the vehicle.
The list of countries covered and PEUGEOT
CONNECT services is available from dealers
or on the website for your country.
In an emergency, press this
button for more than 2

seconds.
The flashing green indicator lamp and the voice
message confirm that the call has been made
to the "Peugeot Connect SOS" call centre*. Pressing this button again
immediately cancels the request.
The green indicator lamp goes
of f.
The green indicator lamp remains on (without
flashing) when communication is established.
It goes off at the end of the call. expressly declined, the call is sent directly
to the emergency services (112) without the
vehicle location.
"Peugeot Connect SOS" immediately locates
your vehicle, contacts you in your own
language** and – if necessary – requests that
relevant emergency services be dispatched**.
In countries where the ser vice is not available,
or when the locating ser vice has been If an impact is detected by the airbag
control unit, and independently of the
deployment of any airbags, an emergency
call is made automatically.
If you benefit from the Peugeot Connect
Packs offer with the SOS and assistance
pack included, there are additional
ser vices available to you in your personal
space, via the website for your country.
Operation of the system
When the ignition is switched on,
the green indicator lamp comes
on for 3
seconds indicating that
the system is operating correctly.
If the orange indicator lamp
flashes then goes off: the system
has a fault.
If the orange indicator lamp is permanently on:
the back-up battery should be replaced.
In both cases, the emergency and assistance
calls ser vice may not work.
Contact a qualified repairer as soon as
possible.
The fault with the system does not prevent
the vehicle being driven.
Peugeot Connect
Assistance
Press this button for more than
2 seconds to request assistance
if the vehicle breaks down.
A voice message confirms that the call has
been made**. Pressing this button again
immediately cancels the request.
5
Safety

51
Seat belts
Front seat belts
The front seat belts are fitted with a
pretensioning and force limiting system.
This system improves safety in the front
seats in the event of a front or side impact.
Depending on the severity of the impact, the
pretensioning system instantly tightens the seat
belts against the body of the occupants.
The pretensioning seat belts are active when
the ignition is on.
The force limiter reduces the pressure of
the seat belt on the passenger’s chest, thus
improving their protection.
Fastening
F Pull the strap then insert the tongue in the buckle.
F

C
heck that the seat belt is fastened
correctly by pulling the strap.
The braking power is never reduced while
the indicator lamp is flashing.
Unfastening
F Press the red button on the buckle.
Front seat belt not fastened/
unfastened warning lamp
When the ignition is switched on,
this warning lamp comes on for a
few seconds, accompanied by an
audible signal, if the driver and/or
the passenger have not fastened
their seat belt. Within one minute after switching on the
ignition, if the driver does not fasten their seat
belt, this warning lamp flashes, accompanied
by an intermittent audible signal.
After about 90
seconds, the warning lamp and
the audible signal will go off, then come on
again and stay on until the driver fastens their
seat belt.
While the vehicle is in motion , if the seat belt
is unfastened, you will be notified by the same
alerts.
Rear seat belts
The rear seats are equipped with two 3 -point
seat belts each fitted with an inertia reel.
5
Safety

54
Airbags
The airbags do not operate when the
ignition is switched off.
This equipment will only deploy once. If a
second impact occurs (during the same or
a subsequent accident), the airbag will not
be deployed again.
Impact detection zones
A.Front impact zone.
B. Side impact zone.
Airbag deployment generates slight
smoke emissions and a noise, due to the
activation of the pyrotechnic cartridge
incorporated in the system.
This smoke is not harmful, but sensitive
individuals may experience slight irritation.
The detonation noise associated with the
deployment of an air bag may result in a
slight loss of hearing for a short time.
The airbags are designed to help enhance the
safety of occupants in the event of a serious
collision. They complement the action of the
safety belts equipped with force limiters.
If a collision occurs, the electronic detectors
record and analyse the front and side impacts
sustained in the impact detection zones:
-

i

f there is a violent impact, the airbags
deploy instantly and help better protect
occupants of the vehicle; immediately after
the impact, the airbags deflate rapidly
in order not to hinder the visibility or the
possible exit of the occupants.
-

i

n the case of a minor or rear impact or in
certain roll-over conditions, the airbags
may not be deployed; the seat belt
alone contributes towards ensuring your
protection in these situations.
Front airbags
This system protects the driver and front
passenger from the risk of injury to the head
and chest in the event of a severe frontal
impact.
The driver's airbag is fitted in the centre of the
steering wheel; the front passenger's airbag is
fitted in the dashboard above the glove box.
Activation
The airbags are deployed (except the
passenger's front airbag if it is deactivated) in
the event of a severe frontal impact to all or part
of the frontal impact zone A , in the longitudinal
centreline of the vehicle on a horizontal plane
and directed from the front to the rear of the
vehicle.
The front airbag inflates between the front
occupant of the vehicle and the dashboard, to
cushion their forward movement.
Safety