ignition Peugeot Partner VU 2001 User Guide

Engine oil level indicator (Diesel)
When the ignition is switched on, the maintenance indicator is displayed for several seconds followed by the engine oil level for approximately 10 seconds. Max Min Check using the oil dipstick.
Check with the vehicle on level ground, and the engine off for at least 10 minutes. Lack of oil (flashing of the lines) The oil level must be topped up. If it is not, the engine may be destroyed.
A flashing of the indicator informs you there is an operating fault .
Contact your network dealer.
30I-14INSTRUMENT PANEL*
Multifunction Display
On switching the ignition on, the display shows in turn :
- Maintenance indicator.- Engine oil level indicator (Diesel).
- Total mileage recorder.
- Indication of the time.
* According to model or country

- Maintenance indicator. The maintenance indicator displays the number of miles to be coveredbefore the next service (in accor-dance with the servicing scheduleswhich appear in the MaintenanceGuide). Operation :On switching on the ignition, the maintenance indicator spannerappears in the display for severalseconds ; the mileage recorder dis-play indicates how many milesremain to be travelled before thenext service is due.
For example :: you have thefol-
lowing distance left to travel before the next service :Five seconds after switching onthe ignition, the total mileagerecorder reverts to normal opera-tion and the total or trip mileages
appear on the display.
Distance to be covered before the next service is less than 1000 miles
For example : 900 miles remain
before the next service is due. For five seconds on switching on the ignition, the display shows : Five seconds after switching on ignition, the total mileage counterresumes its normal function and thespanner symbol remains lit. This signifies that the vehicle will be
due for a service shortly. The total or trip mileages appear on
the display.
The pre-set service distance has been exceeded. The spanner and total number of miles exceeded flash in the displayfor five seconds after the ignition isswitched on. For example : the pre-set service
distance has been exceeded by 300 miles.
Your vehicle must be serviced assoon as possible. Five seconds after switching on ignition, the total mileage counterresumes its normal function andthe spanner symbol remains lit.
28I-14INSTRUMENT PANEL*
Multifunction display
On switching on ignition, the display indicates in succession :

1
11
Maintenance intervals If your vehicle is used in particular- ly harsh conditions, it is necessaryto select the maintenance sche-dules for arduous conditions (seethe Maintenance Guide) whichconsist of more frequent services.Note : if the maximum time bet-
ween two oil changes is reachedbefore the mileage is up, the span-ner symbol lights. To change the maintenanceintervals :
- Switch off the ignition. - Press and hold down button
1.
- Switch on the ignition
- The distance remaining until the next service flashes.
- Release the button immediately.
- The maintenance interval is dis- played.
- Pressing button 1briefly allows
the maintenance intervals to be alternated - When the desired maintenance
interval is displayed, press but-ton 1for ten seconds to validate
(the selected maintenance inter-val will flash for ten seconds).
Release the button to validatewhen the display stops flashing. Resetting the maintenance indi- cator to zero
Your dealer will perform this ope-
ration after each service. However,if you intend to service the vehicleyourself, the procedure for reset-ting the maintenance indicator isas follows:
- Switch off the ignition.- Press and hold down button 1.
- Switch on the ignition.
- The distance remaining until the next service flashes.
- Holdbutton 1down for ten
seconds.
- The display will read Ò=0Óand
the spanner will disappear.
29I-14INSTRUMENT PANEL*
* According to model or country.

B
1 - The clockcan be set, with the ignition on and the engine not running , by pressing button B for more than three
seconds; the hour will start to flash.
Changing the time 2 - Short press on B, allows the time to be changed slowly.
If the button is not pressed for five seconds : The hour is memorised, the minutes flash. Long press, rapid scrolling
Changing the minutes 3 - Short press on B, allows the time to be changed slowly.
If the button is not pressed for five seconds : The minutes are set. Long press, rapid scrolling
Note : the clock display comes on when the driverÕs door is opened and goes out one minute after it is shut. The
clock display goes off after 10 minutes if the driverÕs door remains open.
32I-14INSTRUMENT PANEL*
Digital clock
* According to model or country

Electronic key warning lamp Lights up when switching
on ignition if the key is not recogni- sed
* Depending on version or country.
35I-15WARNING LAMPS *
Minimum coolant fluid level warning lamp If the warning lamp lights
up, it is imperative to stop the vehicle. Check the level and takethe precautions detailed in chapter
ÒLEVELS AND CHECKSÓ).
Battery charge warninglamp Should not be on when the engine is running. If it
comes permanently on, contact
your nearest approved Dealer.
Imperative stopwarning lamp Lights up at the same time as ano-
ther visual warning or if the maxi-mum permissible coolant fluid tem-perature is reached.
Engine oil pressurewarning lamp If it lights up while you are
driving, stop the engine, check the
level, (See ÒLEVELS ANDCHECKSÓ). If it remains lit despite the level being correct, contact your nearest
approved Dealer. Warning lamp for hand-brake and for brakefluid level Indicates that the brake
is applied or incorrectly released. Also that the brake fluid level is
insufficient. See ÒBRAKESÓ,
ÒLEVELS AND CHECKSÓ . The warning lamp may also indica- te a malfunction of the electronicbraking distribution.
Engine operation war-ning lamp (autodiagno-sis)
If it flashes or lights up, this indi-cates a malfunctioning of either theinjection, ignition or emissioncontrol systems (depending oncountry). Quickly consult your nearest
approved dealer.
AIRBAG operation war-ning lamp
See ÒTHE AIRBAG SYSTEMÓ. Doors open warninglamp Lights up when swit- ching on ignition.
Goes out when all the doors are
closed correctly.

Direction indicators Left: move the stalk downwards. Right: move the stalk upwards.
To signal a change of direction, move the stalk past the point of resistance. The signal will cancel automatically as the steering wheel returns.
36I-16SIGNALLING
Horn Press the end of the stalk. Headlamp flash Flick the stalk gently towards you.
It is possible to flash the headlamps when the engine is switched off. Hazard warning This operates all the direction indicators at the same time.
Use it only in case of danger,for an emergency stop or in exceptional dri-
ving circumstances.
It can also operate when the ignition is off.The direction indicators will not operate if the vehicle is driven with the hazard warning lights on.

A
All lights switched off
37I-16SIGNALLING *
LIGHTING CONTROLS (Ring A)
Turn ring Ain the direction of the arrow.
Side lights
Your instrument panel lights.
Turn ring Ain the direction of the arrow.
Dipped beam / main beam
Pull the stalk fully towards you to switch between dipped beam/main beam. Lights on buzzer
It operates when a front door is opened with the ignition off, to indicate that the headlamps are still on. It stops when the door is closed, the headlamps
are switched off or if the ignition is switched on.
Timed illumination of the headlamps
Immediately after switching off ignition, pull the control stalk towards you : the headlamps will come on and then go out automatically after a minute.This will help you, for example, to find your way out of a poorly lit car-park. * According to specification.

AB
22
Manual windows
Turn the handle to raise or lower the windows. Electric windows* The switches
Aand Bon the fascia
are used to raise and lower the dri- ver's and passenger's windows(with ignition switched on and for 1
minute after ignition is switched off). One-touch control Press switch Ato raise or lower
the driver's window to the desired
position. To fully raise or lower the
driver's window, press the switchmore firmly and then release it. Ensure that children are clear of the windows before opening orclosing them. Side windows
To open the side windows, pull the
lever and push the window.
To close, pull then push the lever. CAUTION As a (child) safety measure, remove the ignition key whenleaving the vehicle, even for ashort period.I-11WINDOWS
* According to specification.

Fuel supply cut-off switch This switch is located under the bonnet on the right hand side
To restore the fuel supply after a cut-off, press the top of the switch as shown in the diagram.
87V- 4FUEL CUT-OFF SYSTEM*
If your vehicle is fitted with a device which cuts off the fuel supply, this provides additional safety in the majority or frontal or rear impacts.* According to specification or country.
Before switching the ignition on again,
make sure that there is no fuel leakage or smell of fuel.

These warning lights are tested with the key in the ignition on position : M
64III-1STEERING LOCK-IGNITION-STARTER
¥ S : Steering lock
To release the steering lock, turn the steering wheel slightly, without forcing it, at the
same time as turning the key.
¥ A : Accessories Allows operation of some electrical accessories (radio, electric windows, map rea-
ders, etc.). The battery charge light comes on. ¥ M : Ignition
The following warning lamps * should illuminate : ABS, preheating (Diesel), battery
charge, STOP, oil pressure, handbrake and brake fluid level, engine autodiagnosis,airbags, door closing. If any of these warning lamps do not illuminate, there is a malfunction. ¥ D : Starter Release the key as soon as the engine has started. Never operate the key with the
engine running (see ÒSTARTING THE ENGINEÓ).
* According to model or country