ECO mode Peugeot Partner VU 2001 Owner's Manual

Display :¥ Digital clock.
¥ Maintenance indicator.
¥ Engine oil level indicator (Diesel).
¥ Total mileage recorder.
26I-14INSTRUMENT PANEL*
Tachometer
Coolant temperature gauge Fuel gauge
Display control : ¥ Total mileage recorder.
¥ Trip mileage recorder
¥ Resetting the trip mileage recorder to zero.
Dashboard lighting rheostat see ÒI-14Ó Changing the time see ÒI-14Ó
* According to model or country

1
11
Maintenance intervals If your vehicle is used in particular- ly harsh conditions, it is necessaryto select the maintenance sche-dules for arduous conditions (seethe Maintenance Guide) whichconsist of more frequent services.Note : if the maximum time bet-
ween two oil changes is reachedbefore the mileage is up, the span-ner symbol lights. To change the maintenanceintervals :
- Switch off the ignition. - Press and hold down button
1.
- Switch on the ignition
- The distance remaining until the next service flashes.
- Release the button immediately.
- The maintenance interval is dis- played.
- Pressing button 1briefly allows
the maintenance intervals to be alternated - When the desired maintenance
interval is displayed, press but-ton 1for ten seconds to validate
(the selected maintenance inter-val will flash for ten seconds).
Release the button to validatewhen the display stops flashing. Resetting the maintenance indi- cator to zero
Your dealer will perform this ope-
ration after each service. However,if you intend to service the vehicleyourself, the procedure for reset-ting the maintenance indicator isas follows:
- Switch off the ignition.- Press and hold down button 1.
- Switch on the ignition.
- The distance remaining until the next service flashes.
- Holdbutton 1down for ten
seconds.
- The display will read Ò=0Óand
the spanner will disappear.
29I-14INSTRUMENT PANEL*
* According to model or country.

Engine oil level indicator (Diesel)
When the ignition is switched on, the maintenance indicator is displayed for several seconds followed by the engine oil level for approximately 10 seconds. Max Min Check using the oil dipstick.
Check with the vehicle on level ground, and the engine off for at least 10 minutes. Lack of oil (flashing of the lines) The oil level must be topped up. If it is not, the engine may be destroyed.
A flashing of the indicator informs you there is an operating fault .
Contact your network dealer.
30I-14INSTRUMENT PANEL*
Multifunction Display
On switching the ignition on, the display shows in turn :
- Maintenance indicator.- Engine oil level indicator (Diesel).
- Total mileage recorder.
- Indication of the time.
* According to model or country

AAA
Press button Ato alternate the display between the total mileage recorder
and the trip mileage recorder
31I-14INSTRUMENT PANEL*
Total mileage recorder & Trip mileage recorder
* According to model or country
Resetting the trip mileage recorder to zero Press and hold down button
A, the
display will flash three times and read 0.

B
1 - The clockcan be set, with the ignition on and the engine not running , by pressing button B for more than three
seconds; the hour will start to flash.
Changing the time 2 - Short press on B, allows the time to be changed slowly.
If the button is not pressed for five seconds : The hour is memorised, the minutes flash. Long press, rapid scrolling
Changing the minutes 3 - Short press on B, allows the time to be changed slowly.
If the button is not pressed for five seconds : The minutes are set. Long press, rapid scrolling
Note : the clock display comes on when the driverÕs door is opened and goes out one minute after it is shut. The
clock display goes off after 10 minutes if the driverÕs door remains open.
32I-14INSTRUMENT PANEL*
Digital clock
* According to model or country

Engine oil level indicator (Diesel)
When the ignition is switched on, the maintenance indicator is displayed for several seconds followed by the engine oil level for approximately 10 seconds. Max Min Check using the oil dipstick.
Check with the vehicle on level ground, and the engine off for at least 10 minutes. Lack of oil (flashing of the lines) The oil level must be topped up. If it is not, the engine may be destroyed.
A flashing of the indicator informs you there is an operating fault .
Contact your network dealer.
30I-14INSTRUMENT PANEL*
Multifunction Display
On switching the ignition on, the display shows in turn :
- Maintenance indicator.- Engine oil level indicator (Diesel).
- Total mileage recorder.
- Indication of the time.
* According to model or country

AAA
Press button Ato alternate the display between the total mileage recorder
and the trip mileage recorder
31I-14INSTRUMENT PANEL*
Total mileage recorder & Trip mileage recorder
* According to model or country
Resetting the trip mileage recorder to zero Press and hold down button
A, the
display will flash three times and read 0.

1
11
Maintenance intervals If your vehicle is used in particular- ly harsh conditions, it is necessaryto select the maintenance sche-dules for arduous conditions (seethe Maintenance Guide) whichconsist of more frequent services.Note : if the maximum time bet-
ween two oil changes is reachedbefore the mileage is up, the span-ner symbol lights. To change the maintenanceintervals :
- Switch off the ignition. - Press and hold down button
1.
- Switch on the ignition
- The distance remaining until the next service flashes.
- Release the button immediately.
- The maintenance interval is dis- played.
- Pressing button 1briefly allows
the maintenance intervals to be alternated - When the desired maintenance
interval is displayed, press but-ton 1for ten seconds to validate
(the selected maintenance inter-val will flash for ten seconds).
Release the button to validatewhen the display stops flashing. Resetting the maintenance indi- cator to zero
Your dealer will perform this ope-
ration after each service. However,if you intend to service the vehicleyourself, the procedure for reset-ting the maintenance indicator isas follows:
- Switch off the ignition.- Press and hold down button 1.
- Switch on the ignition.
- The distance remaining until the next service flashes.
- Holdbutton 1down for ten
seconds.
- The display will read Ò=0Óand
the spanner will disappear.
29I-14INSTRUMENT PANEL*
* According to model or country.

B
1 - The clockcan be set, with the ignition on and the engine not running , by pressing button B for more than three
seconds; the hour will start to flash.
Changing the time 2 - Short press on B, allows the time to be changed slowly.
If the button is not pressed for five seconds : The hour is memorised, the minutes flash. Long press, rapid scrolling
Changing the minutes 3 - Short press on B, allows the time to be changed slowly.
If the button is not pressed for five seconds : The minutes are set. Long press, rapid scrolling
Note : the clock display comes on when the driverÕs door is opened and goes out one minute after it is shut. The
clock display goes off after 10 minutes if the driverÕs door remains open.
32I-14INSTRUMENT PANEL*
Digital clock
* According to model or country

ABS system*
This system increases safety by preventing the wheels from locking in the event of harsh braking or in conditions of poor grip. It enables the driver to maintain control of the steering.
The operating capacity of all the essential electrical elements of the ABS system is controlled by an electronic moni-
toring system both before and during driving. The ABS light comes on when the ignition is switched on, and should
go out after approximately two seconds. If the light does not go out, this indicates that the ABS is disconnected due
to a fault. Likewise, if the light comes on while driving, this indicates that the ABS is not operating. In both cases,
the normal braking system remains effective, as on a vehicle without ABS. However, to avoid the occurrence of other
faults with unknown consequences, the ABS should be inspected as soon as possible by an approved dealer.
It is still necessary to drive carefully on slippery surfaces (loose stones, snow, ice, etc.)..
67III-3BRAKES
Handbrake
The handbrake is operated by pulling the lever upwards. The greater the slope you are on, the greater the force that should be applied in pulling the
lever.
To ease the action of the handbrake lever, it is recommended that you press the brake pedal at the same time. As a precaution, 1st gear should be engaged in all cases. On steep slopes, you should also turn the wheels towards the kerb.
To release the handbrake, pressthe button while pulling the lever up, then
lower the lever to the fully down position.The warning light comes on if the handbrake is on or not fully released, with the ignition on.
* According to model or country.