lock Ram 1500 2020 Workshop Manual

138 GETTING TO KNOW YOUR VEHICLE
RamBox Push Button And Keyhole LockThe interior of the RamBox will automatically illuminate
when the lid is opened. The timing can be adjusted through
your touchscreen.
Refer to “Uconnect Settings” in “Multimedia” for further
information.
Cargo bins feature two removable drain plugs (to allow
water to drain from bins). To remove plug, pull up on the
edge. To install push plug downward into drain hole.
If equipped, a power inverter can be found inside the
RamBox.
Refer to “Electrical Power Outlets” in this chapter for further
information.
NOTE:
Provisions are provided in the bins for cargo dividers. These
accessories (in addition to other RamBox accessories) are
available from Mopar.
1 — Keyhole Lock
2 — Push Button
CAUTION!
Leaving the lid open for extended periods of time could
cause the vehicle battery to discharge. If the lid is
required to stay open for extended periods of time, it is
recommended that the bin lights be turned off manually
using the on/off switch.
2020_DT_1500_OM_US.book Page 138

GETTING TO KNOW YOUR VEHICLE 139
Locking And Unlocking RamBox
Push and release the lock or unlock button on the key fob to
lock and unlock all doors, the tailgate and the RamBox (if
equipped). Refer to “Keys” in this chapter for further details.
To unlatch the storage bin manually, insert the emergency
key into the keyhole and turn clockwise. Always return the
key to the upright (vertical) position before removing it from
the keyhole.RamBox Safety Warning
Carefully follow these warnings to help prevent personal
injury or damage to your vehicle:
CAUTION!
• Ensure cargo bin lids are closed and latched before moving or driving vehicle.
• Loads applied to the top of the bin lid should be mini -
mized to prevent damage to the lid and latching/
hinging mechanisms.
• Damage to the RamBox bin may occur due to heavy/ sharp objects placed in bin that shift due to vehicle
motion. In order to minimize potential for damage,
secure all cargo to prevent movement and protect inside
surfaces of bin from heavy/sharp objects with appro -
priate padding.
WARNING!
• Always close the storage bin covers when your vehicle is unattended.
• Do not allow children to have access to the storage bins. Once in the storage bin, young children may not be able
to escape. If trapped in the storage bin, children can die
from suffocation or heat stroke.
• In an accident, serious injury could result if the storage bin covers are not properly latched.
• Do not drive the vehicle with the storage bin covers open.
• Keep the storage bin covers closed and latched while the vehicle is in motion.
• Do not use a storage bin latch as a tie down.2
2020_DT_1500_OM_US.book Page 139

140 GETTING TO KNOW YOUR VEHICLE
RamBox Storage Bin Cover Emergency Release Lever —
If Equipped
As a security measure, a Storage Bin Cover Emergency
Release is built into the storage bin cover latching mecha-
nism.
Storage Bin Cover Emergency Release Lever NOTE:
In the event of an individual being locked inside the storage
bin, the storage bin cover can be opened from inside of the
bin by pulling on the glow-in-the-dark lever attached to the
storage bin cover latching mechanism.
Bed Divider — If Equipped
The bed divider has two functional positions:
• Storage Position
• Divider Position
Storage Position
The storage position for the bed divider is at the front of the
truck bed which maximizes the bed cargo area when not in
use.
2020_DT_1500_OM_US.book Page 140

GETTING TO KNOW YOUR VEHICLE 141
To install the bed divider into the storage position, perform
the following:
1. Make sure the center handle is unlocked using the vehiclekey and rotate the center handle vertically to release the
divider side gates.
Center Handle And Lock 2. With the side gates open, position the divider fully
forward in the bed against the front panel.
Storage Position
1 — Center Handle Lock
2 — Handle
2
2020_DT_1500_OM_US.book Page 141

142 GETTING TO KNOW YOUR VEHICLE
3. Rotate the side gates closed allowing the outboard ends tobe positioned in front of the cargo tie down loops.
Cargo Tie Down Loop 4. Rotate the center handle horizontally to secure the side
gates in the closed position.
Side Gates Closed
5. Lock the center handle using the vehicle key to secure the panel into place.
2020_DT_1500_OM_US.book Page 142

GETTING TO KNOW YOUR VEHICLE 143
Divider Position
The divider position is intended for managing your cargo
and assisting in keeping cargo from moving around the bed.
There are 11 divider slots along the bed inner panels which
allow for various positions to assist in managing your cargo.
To install the bed divider into a divider position, perform the
following:
1. Make sure the center handle is unlocked using the vehiclekey and rotate the center handle vertically to release the
divider side gates.
Center Handle And Lock
1 — Center Handle Lock
2 — Handle
2
2020_DT_1500_OM_US.book Page 143

144 GETTING TO KNOW YOUR VEHICLE
2. With the side gates open, position the divider so theoutboard ends align with the intended slots in the sides of
the bed.
Aligning Gate To Slots
3. Rotate the side gates closed so that the outboard ends are secured into the intended slots of the bed.
4. Rotate the center handle horizontally to secure the side gates in the closed position. Side Gates Closed
5. Lock the center handle to secure the panel into place.
Bed Rail Tie-Down System
CAUTION!
The maximum load per cleat should not exceed 250 lbs
(113 kg), or 500 lbs (227 kg) total per rail, and the angle of
the load on each cleat should not exceed 45 degrees
above horizontal, or damage to the cleat or cleat rail may
occur.
2020_DT_1500_OM_US.book Page 144

GETTING TO KNOW YOUR VEHICLE 145
NOTE:
This feature is available for vehicles both equipped, or not
equipped, with a RamBox.
There are two adjustable cleats on each side of the bed that
can be used to assist in securing cargo.Adjustable Cleats
Each cleat must be located and tightened down in one of the
detents, along either rail, in order to keep cargo properly
secure. To move the cleat to any position on the rail, turn the nut
counterclockwise, approximately three turns. Then pull out
on the cleat and slide it to the detent nearest the desired loca
-
tion. Make sure the cleat is seated in the detent and tighten
the nut.
Adjustable Cleat Assembly
1 — Utility Rail Detent
2 — Cleat Retainer Nut
3 — Utility Rail Cleat
2
2020_DT_1500_OM_US.book Page 145

148 GETTING TO KNOW YOUR VEHICLE
2. Remove the connector bracket from the sill by pushinginward in the locking tab.
Locking Tab
3. Disconnect the chassis wiring harness, ensuring the connector bracket does not fall into the sill. 4. Connect the chassis plug and bracket (provided in the
glove compartment) to the chassis wiring harness and
insert the bracket back into the sill.
5. Connect the tailgate plug (provided in the glove compart -
ment) to the tailgate wiring harness to ensure that the
terminals do not corrode.
6. Tape the tailgate harness and bracket against the forward-facing surface of the tailgate. This will prevent
damaging the connector and bracket when storing or
reinstalling the tailgate.
Removing The Tailgate
1. Disconnect the wiring harness for the rear camera and orpower locks (if equipped).
NOTE:
Refer to “Disconnecting The Rear Camera And Remote
Keyless Entry” in this section.
2020_DT_1500_OM_US.book Page 148

GETTING TO KNOW YOUR VEHICLE 149
2. Unlatch the tailgate and remove the support cables byreleasing the lock tang from the pivot.
NOTE:
Make sure tailgate is supported when removing support
cables.
Locking Tang 3. Position the tailgate on a 45 degree angle.
4. Raise the right side of the tailgate until the right side pivot
clears the hanger bracket.
5. Without latching, rotate the tailgate to nearly closed, then slide the entire tailgate to the right to free the left side
pivot.
6. Remove the tailgate from the vehicle.
NOTE:
Do not carry the tailgate loose in the truck pickup box.
WARNING!
To avoid inhaling carbon monoxide, which is deadly, the
exhaust system on vehicles equipped with “Cap or
Slide-In Campers” should extend beyond the
overhanging camper compartment and be free of leaks.
2
2020_DT_1500_OM_US.book Page 149