light RENAULT ESPACE 2012 J81 / 4.G Workshop Manual

JauneNoirNoir texte
2.13
ENG_UD20368_1
Conseils antipollution, économies de carburant, conduite (X81 - J81 \
- Renault)ENG_NU_932-3_X81ph3_Renault_2
– Brake as little as possible by suitably
anticipating an obstacle or bend and
then simply releasing the accelerator
pedal.
– Avoid sudden acceleration.
– Do not try to maintain the same
speed up a hill, accelerate no more
than you would on the level. Keep
your foot in the same position on the
accelerator pedal.
– Double declutching and accelerating
before switching off are unnecessary
in modern vehicles.
– Bad weather, flooded roads.
ADvIcE: antipollution, fuel economy and driving (continued)
Do not drive through floods if
the water is above the lower
edge of the wheel rims.
Exhaust gas monitoring
system
The exhaust gas monitoring system will
detect any operating faults in the vehi-
cle’s antipollution system.
If this system malfunctions, toxic sub-
stances may be released into the at -
mosphere or damage may occur.
ÄThis warning light on the in -
strument panel will indicate if
there are any faults in the system:
This lights up when the ignition is
switched on and goes out when the
engine is started.
– If it lights up continuously, consult
your approved dealer as soon as
possible;
– if it flashes, reduce the engine speed
until the light stops flashing. Contact
your approved dealer as soon as
possible.
Driving– Drive carefully for the first few miles
until the engine reaches its normal
operating temperature, rather than
let it warm up while the vehicle is sta-
tionary.
– Speed is expensive.
– Sporty driving uses a lot of fuel: drive
with a light right foot.
– Do not overrev the engine in the in-
termediate gears.
Always use the highest gear possi -
ble without labouring the engine.
On versions with an automatic trans-
mission, it is preferable to keep the
gear lever in position D.
Obstructions to the driver
On the driver ’s side, only
use mats adapted to the ve-
hicle that attach to the pre-
installed parts, and regularly check
their mounting. Do not place several
mats on top of each other.
Risk of pedals jamming

2.14
ENG_UD20368_1
Conseils antipollution, économies de carburant, conduite (X81 - J81 \
- Renault)ENG_NU_932-3_X81ph3_Renault_2
ADvIcE: antipollution, fuel economy and driving (continued)
Advice on use
– Electricity is fuel: switch off all electri-
cal components when you no longer
need them. However (safety first),
keep your lights on when the visibil -
ity is poor (“see and be seen”).
– Use the air vents. Driving with the
windows open at 60 mph (100 km/h)
will increase fuel consumption by
4%.
– Do not leave an empty roof rack
fitted to the vehicle. –
In vehicles fitted with air condi -
tioning , it is normal to observe an
increase in fuel consumption (es -
pecially in city conditions) when
it is used. For vehicles fitted with
manual air conditioning, switch off
the system when it is not required.
In order to minimise consumption
and help to protect the environ -
ment: it is recommended to drive
with the air vents on and the win -
dows closed. If the vehicle has been
parked in the sun, open the doors
for a few moments to let the hot air
escape before starting the engine.
– Never fill the fuel tank right to the
brim to avoid overflow.
– It is better to fit a trailer for bulky ob-
jects.
– When towing a caravan, fit a wind
deflector and adjust it carefully. –
Avoid using the vehicle for door -
to-door calls (short journeys with
long waits in between) because the
engine never reaches its normal op-
erating temperature.
Tyres
– Under-inflated tyres increase fuel
consumption.
– The use of non-recommended tyres
can increase fuel consumption.

JauneNoirNoir texte
2.19
ENG_UD20370_1
Système de surveillance de pression des pneus (X81 - J81 - Renault)\
ENG_NU_932-3_X81ph3_Renault_2
TYRE PRESSURE MONITOR
“check tyre pressure”
A shaded wheel B indicates a deflated
tyre.
“Inflate tyres to motorway
pressure”
The tyre pressure is not suitable for the
speed of travel. Slow down or inflate
all four tyres to “motorway pressure”
(refer to the label located on the label
on the edge of the driver’s door).
“Wheel sensors missing”
One wheel A disappears, indicating
that the sensor on this wheel is missing
or faulty (e.g. if the emergency spare
wheel is fitted).
“Stop! Tyre puncture”
Replace the wheel B concerned or call
your approved dealer.
This message appears along with the
û warning light.
Operating faults
In certain conditions involving readjust-
ment of tyre pressures, the fault mes -
sage may continue to be displayed (for
approximately 1 hour and 45 minutes
after the vehicle has stopped).
A
B
Examples of messages which may appear on the display

Electronic Stability Program: ESP ........ (up to the end of the DU)
ESP: Electronic Stability Program ........ (up to the end of the DU)
2.20
ENG_UD20371_1
Contrôle dynamique de conduite : E.S.P. avec contrôle de sous-virage (X81 - J81 - Renault)
ENG_NU_932-3_X81ph3_Renault_2
Electronic Stability Program: ESP
ELEcTRONIc STABILITY PROGRAM: ESP
This system helps to keep control of
the vehicle in critical driving situations
(avoiding an obstacle, loss of grip when
cornering, etc.) and works in conjunc -
tion with the understeer control system.
This function is an addi -
tional aid in the event of
critical driving conditions,
enabling the vehicle behav -
iour to be adapted to suit the driving
conditions.
However, the function does not take
the place of the driver. It does not
increase the vehicle’s limits and
should not encourage you to
drive more quickly.
Therefore, it can under no circum -
stances replace the vigilance or re-
sponsibility of the driver when ma -
noeuvring the vehicle (the driver
must always be ready for sudden in-
cidents which may occur when driv-
ing).
Operating principle
A sensor in the steering wheel detects
the direction selected by the driver.
Other sensors throughout the vehicle
measure the actual direction.
The system compares the direction se-
lected by the driver and the actual di -
rection of the vehicle and corrects this
as necessary by applying the brakes
selectively and/or acting on the engine
power. When the function begins to operate,
warning light
A flashes to warn you.
If the warning light comes on accom -
panied by the “ESP deactivated” mes -
sage when the engine is started, turn
the steering wheel from lock to lock to
reinitialise the system.
Understeer control
This system optimises the action of the
ESP in the case of pronounced unders-
teering (loss of front axle road holding).
Operating faults
When the system detects an operat -
ing fault the message “Check ESP” ap-
pears on the instrument panel along
with the
ú warning light and warn-
ing light A.
Consult an approved dealer.
A

traction control ...................................... (up to the end of the DU)
traction control: ASR .............................(up to the end of the DU)
driving ................................................... (up to the end of the DU)
2.21
ENG_UD20372_1
Système antipatinage : A.S.R. (X81 - J81 - Renault)
ENG_NU_932-3_X81ph3_Renault_2
Traction control: ASR
TRAcTION cONTROL: ASR (1/2)
This system helps to limit wheelspin of
the drive wheels and to control the vehi-
cle when pulling away or accelerating.
This function is an addi -
tional aid in the event of
critical driving conditions,
enabling the vehicle behav -
iour to be adapted to suit the driving
conditions.
However, the function does not take
the place of the driver. It does not
increase the vehicle’s limits and
should not encourage you to
drive more quickly.
Therefore, it can under no circum -
stances replace the vigilance or re-
sponsibility of the driver when ma -
noeuvring the vehicle (the driver
must always be ready for sudden in-
cidents which may occur when driv-
ing).
Operating principle
Using the wheel sensors, the system
measures and compares the speed of
the drive wheels at all times and slows
down their over-rotation.
If a wheel is starting to slip, the system
brakes automatically until the drive sup-
plied becomes compatible with the level
of grip under the wheel again. The system also adjusts the engine
speed to the grip available under the
wheels, independently of the pressure
exerted on the accelerator pedal.
When the function begins to operate,
warning light
A flashes to warn you.
A

2.22
ENG_UD20372_1
Système antipatinage : A.S.R. (X81 - J81 - Renault)
ENG_NU_932-3_X81ph3_Renault_2
TRAcTION cONTROL: ASR (2/2)
Disabling the function
In some situations (driving on very wet
ground: snow, mud, etc. or driving with
snow chains fitted), the system may
reduce the engine output to limit wheel -
spin. If this is not required, it is possible
to deactivate the function by pressing
switch 1.
The message “‘ESP deactivated” ap -
pears to inform you, accompanied by
warning light A.
Disabling the function also disables the
ESP function.
Correct this as soon as possible by
pressing switch 1 again.
Traction control is automatically reacti-
vated when the ignition is switched on.
Operating faults
If the system detects an operating fault,
the message “Check ESP” is displayed
on the instrument panel display along
with the
ú warning light and warn-
ing light A.
Consult an approved dealer.
If the warning light comes on accom -
panied by the “ESP deactivated” mes -
sage when the engine is started, turn
the steering wheel from lock to lock to
reinitialise the system.
1
A

2.24
ENG_UD20373_1
Système antiblocage des roues (ABS) (X81 - J81 - Renault)
ENG_NU_932-3_X81ph3_Renault_2
ANTI-LOcK BRAKING SYSTEM: ABS (continued)
One of two situations may arise if there
is a fault in the ABS system:
1 – Orange warning light
x is lit
on the instrument panel.
Braking is still performed, but without
the ABS system. Contact an approved
Dealer as soon as possible.
2 – Orange warning light
x and red brake cir -
c u i t i n c i d e n t w a r n i n g
light
D are lit on the instru -
ment panel.
This indicates that both the brak -
ing system and the ABS system
are faulty. Your braking systems are
only partially operational. However,
it is dangerous to brake suddenly
and it is essential to stop immedi -
ately, as soon as traffic conditions
allow. Contact an approved Dealer.
Also, on equipped vehicles, the mes -
sage “Check ABS” appears on the dis-
play A.
The braking modulation provided by
the ABS is independent of the effort
applied to the brake pedal. In an
emergency, apply firm and contin-
uous pressure to the brake pedal
There is no need to pump it repeat-
edly.
A

emergency brake assist......................................... (current page)
emergency braking ............................... (up to the end of the DU)
driving ................................................... (up to the end of the DU)
2.25
ENG_UD1792_1
Assistance au freinage d’urgence (X81 - Renault)
ENG_NU_932-3_X81ph3_Renault_2
Assistance au freinage d’urgence
EMERGENcY BRAKE ASSIST
This system is complementary to the
ABS and helps reduce vehicle stopping
distances.
Operating principle
The system allows an emergency brak-
ing situation to be detected via a sensor
that measures the speed with which the
brake pedal is depressed. In this case,
the braking assistance instantly pro -
vides its maximum power.
ABS braking is maintained as long as
the brake pedal is applied.
Hazard warning lights
activation
These may light up in the event of rapid
deceleration.
In this case, the hazard warning lights
may be switched off by pressing the
hazard warning lights switch twice.
This function is an addi -
tional aid in the event of
critical driving conditions,
enabling the vehicle behav -
iour to be adapted to suit the driving
conditions.
However, the function does not take
the place of the driver. It does not
increase the vehicle’s limits and
should not encourage you to
drive more quickly.
Therefore, it can under no circum -
stances replace the vigilance or re-
sponsibility of the driver when ma -
noeuvring the vehicle (the driver
must always be ready for sudden in-
cidents which may occur when driv-
ing).

cruise control-speed limiter....................................(current page)
speed limiter ......................................... (up to the end of the DU)
driving ................................................... (up to the end of the DU)
2.26
ENG_UD1793_1
Régulateur-Limiteur de vitesse : fonction limiteur (X81 - Renault)
ENG_NU_932-3_X81ph3_Renault_2
Jaune NoirNoir texte
Limiteur de vitesse
cRUISE cONTROL - SPEED LIMITER: limiter function
The speed limiter function helps you
stay within the driving speed limit that
you choose.
This may be useful, for example, driving
in urban areas or areas with a speed re-
striction (roadworks), etc.
The system operates from a driving
speed of about 18 mph (30 km/h).controls
1 Main “On/Off” switch.
2 Limit speed memorisation and ad -
justment of limit speed (increasing).
3 Recall of stored limit speed.
4 Switching the function off (with limit
speed storage).
5 Limit speed memorisation and ad -
justment of limit speed (decreasing).ÌIndicator light
This indicator light on the in -
strument panel lights up to indicate that
the limiter function is in operation.
The stored speed information appears
on trip computer and warning system 6.
1
2
5
3
4
6

JauneNoirNoir texte
2.27
ENG_UD1793_1
Régulateur-Limiteur de vitesse : fonction limiteur (X81 - Renault)
ENG_NU_932-3_X81ph3_Renault_2
cRUISE cONTROL - SPEED LIMITER: limiter function (continued)
Switching onPress switch 1 on the side showing
Ì.
The indicator light on the instrument
panel lights up and, depending on the
vehicle, the trip computer or the infor -
mation display enters “speed limiter”
mode.
Limiting the speedAt a constant speed (above about
18 mph (30 km/h)) and in the correct
gear (for vehicles with manual gear -
boxes), press switch 2 : the speed is
stored.
Driving
When a limit speed has been memo -
rised, if this speed is not reached the
vehicle behaves in a similar way to a
vehicle without the speed limiter func -
tion.
Once this speed is reached, no effort
on the accelerator pedal will allow
you to exceed the programmed speed
except in an emergency (refer to infor-
mation on “Exceeding the limit speed”).
The system is designed in such a
way that it is possible to detect a dif-
ference between the programmed
speed and the speed shown on the
instrument panel.
v arying the limit speed
The limit speed may be changed by
pressing repeatedly or holding down:
– button 2 to increase the speed,
– button 5 to decrease the speed.
1
2
5