ESP RENAULT KANGOO 1997 KC / 1.G Electrical Equipment Workshop Manual

5.Connect the XR25, setting the ISO selector to
S8.
Enter code
Bargraphs
19 RH and 19 LH must be illumina-
ted (programming not carried out).
6. With one of the keys switch the ignition on
for approximately 2 seconds (without star-
ting the engine). Bargraph 18
LH illuminates
and bargraph
19 LH extinguishes.
The red immobiliser warning light flashes rapi-
dly.
7.Switch the ignition off and start command
G60* to lock the programming.
- the red immobiliser warning light should
flash (slow flashing)
- bargraphs 19 RH and 18 LH should be ex-
tinguished.
8.Switch the ignition on for a few seconds,
check that the red immobiliser warning light
is illuminated permanently (diesel) or that
the injection warning light is flashing (pe-
trol).
9.Switch the ignition on for more than 10
consecutive seconds.
10.Switch the ignition off and wait for the red
immobiliser warning light to flash slowly.
Enter command
with the ignition still off (bargraph
9 LH illu-
minates).
Switch the ignition on, the red immobiliser
warning light flashes more rapidly.
Follow the procedure for entering the securi-
ty code (see procedure for entering the secu-
rity code), using the code number correspon-
ding to the old kit. This erases the old code
memorised in the injection computer or the
coded solenoid valve.
IMMOBILISER
Coded key immobiliser system
REPLACING A KIT
(decoder unit plus two key heads)
If a kit is replaced it will be necessary to:
- programme the codes of the 2 new keys in the
new decoder unit (supplied uncoded).
- erase the old code in the injection computer or
coded solenoid valve using the security proce-
dure (the code number for the old kit should be
requested from the local assistance network,
example Delta Assistance for France, NVSR for
the UK by fax only)
IMPORTANT : to erase the old code (memorised in
the injection computer or coded solenoid valve
electronic unit), the procedure described below
must be followed in the correct order.
The code in the injection computer or coded sole-
noid valve cannot be erased with the security code
(using the number for the old kit) unless the deco-
der unit fitted to the vehicle has been program-
med with a different code (which is the case in the
following procedure).
NOTE : if the security code is entered when the
decoder unit has the same code as the injection
computer, or coded solenoid valve, it will not be
decoded.
1.Fit the metal inserts from the old keys into
the new key heads.
2.Note the number of one of the old keys to
obtain the security code number.
3.Remove the decoder unit with the ignition
off.
4.Fit the new decoder unit, ignition off.
82
G04*
D56
82-8

REPLACING THE INJECTION COMPUTER OR
CODED SOLENOID VALVE
The injection computer and coded solenoid valve
are supplied uncoded. The engine immobiliser
code must be programmed in when they are fit-
ted.
It is sufficient to carry out the following opera-
tions:
- switch the ignition on, without starting the en-
gine, using the vehicle’s coded key for a few
seconds,
- switch the ignition off, the immobiliser will be
activated approximately 10 seconds afterwards
(red immobiliser warning light flashes).
NOTE : starting prevention can be checked
using the XR25:
- Ignition off, wait for the warning light to
flash (slow flashing)
Enter
ignition still off (bargraph
9 LH illuminates).
- Switch the ignition on, the red immobiliser
warning light should flash more quickly and
the vehicle should be impossible to start.
NOTE : For removal - refitting information, refer
to the corresponding section (13 or 17).
IMMOBILISER
Coded key immobiliser system
12.Check the immobiliser system operates cor-
rectly with both keys.
Switch the ignition on and check that the red
warning light illuminates for 3 seconds then
extinguishes and that the vehicle can be star-
ted.
NOTE : starting prevention can be checked
using the XR25:
- Ignition off, wait for the warning light to
flash (slow flashing)
Enter
- Switch the ignition on and check the vehi-
cle cannot be started and that the red war-
ning light flashes (rapid flashing).
13.The procedure is complete. After turning the
ignition off and on again (for more than 2 se-
conds), check the vehicle can be started and
erase all faults present in the decoder unit.
Vehicles fitted with a remote control
After replacing the kit carry out a resynchronisa-
tion operation (see simple resynchronisation pro-
cedure, section 88).
82
G04*
G04*
82-10

IMMOBILISER
Coded key immobiliser system
82
KEY
104 Ignition switch
120 Injection computer
123 Door locking button
138 Rear right door locking motor
140 Driver’s door locking motor
141 Passenger’s door locking motor
142 Luggage compartment door locking motor
154 Luggage compartment door switch
178 Rear right door switch
180 Driver’s door switch
181 Passenger’s door switch
213 Courtesy light
225 Diagnostic socket
247 Injection warning light and red immobiliser
warning light on instrument panel
249 Remote control receiver
260 Passenger compartment fuse box
503 Decoder unit
711 Coded solenoid valveFAULT FINDING
If this immobiliser system is faulty, fault finding
may be carried out using the XR25.
CONNECTION
Use cassette no° 17 and the corresponding fault
finding fiche no° 56.
92656S2
Connect the XR25 to the diagnostic socket.
Position the ISO selector on S8.
Enter the code for the immobiliser system D56.
NOTE : For information on the interpretation of
the bargraphs, the fault charts, checking confor-
mity and additional tests, refer to the fault fin-
ding section.
82-16

INSTRUMENT PANEL
Instrument panel
83
DESCRIPTION
- electronic speedometer,
- display : mileometer/trip recorder and clock
- coolant temperature gauge,
- fuel gauge,
- warning light functions.
13054S
1 Trip mileometer reset button and clock reset (rotate).
NOTE :
• Under normal operating conditions, the oil level is only measured if the ignition has been switched off for
over one minute; otherwise the old oil level value is re-displayed.
If a fault is detected, however, an oil level measurement is made each time the ignition is switched on to
check if the fault is persisting.
• It is normal to find that the oil level is not always the same:
- parking on a slope,
- too short a wait after running the engine for a short moment (especially when the oil is cold), ...
83-7

WIRING
Airbags and seat belt pretensioners
88
WARNING LIGHT ON THE DASHBOARD
This warning light controls the pretensioners and
airbags, except for vehicles fitted with pretensio-
ners only.
It should illuminate for a few seconds when the
ignition is switched on, then extinguish (and
remain extinguished). If it does not illuminate
when the ignition is switched on, or illuminates
when the vehicle is being driven, there is a fault in
the system (see fault finding section).
IMPORTANT : the systems MUST be checked by
means of the
XRBAG, following:
- an accident which has not given rise to
triggering,
- theft or attempted theft of the vehicle,
- before the sale of a used vehicle.
These systems are not triggered in the case of:
- a lateral impact,
- a rear impact.
When it is triggered the pyrotechnic gas
generator produces an explosion combined with
light smoke.
NOTE : With pretensioners only,the computer has
a single sensor (electromechanical).
OPERATIONS ON THE TRIGGER LINES
If a fault is noted on one of these lines, the
component must be renewed and not repaired.
This safety equipment cannot be subjected to any
conventional wiring or connector repair opera-
tions.
The airbag trigger wiring is integrated into the
passenger compartment wiring loom . To make
replacement easier, cut the two ends of the faulty
wiring and run the new wiring along the same
routing, alongside the passenger compartment
wiring loom.
IMPORTANT : When fitting the new wiring, en-
sure it is not in danger of being cut or rubbed and
that the original wiring cleanliness is respected.
NOTE : The trigger lines are supplied by the Parts
Department in a kit containing both airbag and
pretensioner wiring.
OPERATION WITH AIRBAG(S) AND PRETENSIONER
EQUIPMENT
When the ignition is switched on, the
warning light illuminates for a few
seconds then extinguishes.
This computer is then on standby and notes dece-
lerations of the vehicle using the signal measured
by the integral decelerometer.
When a frontal impact of sufficient strength oc-
curs it triggers the simultaneous ignition of the
pyrotechnic generators of the two seat belt pre-
tensioners after receiving confirmation of detec-
tion of an impact by the electromechanical safety
sensor.
Under the action of the gases generated by the
system, a piston is displaced in its cylinder,
carrying with it a cable connected to the
corresponding central catch, thus enabling the
seat belt to be retracted (see pretensioner
section).
If the frontal impact is greater than this, the dece-
lerometer triggers the ignition of the pyrotechnic
gas generators which inflate the driver and pas-
senger airbags once the impact has been valida-
ted by the electromechanical safety sensor.
88-17