fuel filter RENAULT KANGOO 1997 KC / 1.G Engine And Peripherals Workshop Manual

Contents
Consumables
Identification
Oil consumption
Oil pressure
Engine - Gearbox
Engine and transmission assembly
Sump
Crankshaft seal, timing end
Oil pump10-1
10-1
10-2
10-3
10-4
10-9
10-25
10-29
10-30
TOP AND FRONT OF ENGINE
Timing belt
Cylinder head gasket
Replacement of valve adjustersPage Page
11
Engine and
peripherals
11-1
11-11
11-29 ENGINE AND PERIPHERALS
10FUEL SUPPLY -
DIESEL EQUIPMENT
Fuel supply
Fuel cut off in case of an impact
Injector gallery
Fuel filter
Pump flow
Fuel pressure
Antipercolation device
Diesel equipment
General
Specifications
Location of components
Advance solenoid valve
Altimetric corrector
Fast idle LDA
Coded solenoid valve
Load potentiometer
Computer configuration
Injector with sensor (needle
lift)
Injection warning light
Pre-postheating control
Fast idle control
Injection/air conditioning
programming
Computer
Defect modes
Pump
Pump -Timing
Idle speed settings13-1
13-2
13-6
13-7
13-8
13-12
13-13
13-14
13-16
13-19
13-22
13-25
13-26
13-28
13-29
13-31
13-32
13-33
13-35
13-36
13-36
13-37
13-38
13-39
13-41
13-4613
FUEL MIXTURE
Specifications
Throttle body
Inlet manifold
Exhaust manifold
Inlet-exhaust manifolds12-1
12-7
12-15
12-18
12-2012

ENGINE AND ENGINE PERIPHERALS
Engine and transmission assembly
10
12988R
- the exhaust heat shield and the gear control
on the lever and gearbox sides,
- the exhaust downpipe,
- the earth strap on the gearbox,
- the front bumper,
- the air intake pipe of the air filter,
- the fuel supply and return unions (A) and (B),
- the connectors (2), (3), (4) and (5).
Unclip the fuel pipes from the air filter unit and
the timing cover and unclip the diesel filter from
its support and move the assembly to one side.
13083-1R
F8Q engine
10-20

12mm torx socket
Angular tightening wrench
TOP AND FRONT OF ENGINE
Cylinder head gasket
11
SPECIAL TOOLING REQUIRED
Mot. 591-04 Angle wrench for tightening
cylinder head and index
Mot. 1202 Hose clip pliers
Mot. 1273 Tool for checking belt tension
Mot. 1379 Tool for securing engine to
subframe
EQUIPMENT REQUIRED
TIGHTENING TORQUES (in daN.m)
Crankshaft output mounting bolt 2 + 90°
Mounting bolt for front right suspended
engine mounting on engine 6.2
Mounting bolt for front right suspended
engine mounting on vehicle body 6.2
Timing belt tension wheel nut 5
Wheel bolts 9
REMOVAL
Put the vehicle on a 2 post lift.
Remove the bonnet, and the right hand wheel .
Disconnect the battery.
Drain the cooling circuit.
Fit the engine support tool, Mot. 1379.Remove:
- the timing belt (see method described in
section 11 "Timing belt"),
- the dipstick,
- the brake servo pipe,
- the air filter,
- the accelerator cable,
- the fuel supply and return pipes level with the
timing belt cover on the cylinder head
D7F Engine
11-11

TOP AND FRONT OF ENGINE
Cylinder head gasket
11
Remove :
- the exhaust downpipe,
- the hoses and connectors of the cylinder head
coolant pipe housing outlet,
- the connection at (1) using tool Mot. 1311-06,
13097R
99461R
- the air filter assembly by disconnecting the
EGR solenoid valve and the air temperature
sensor (unclip the fuel supply pipes from the
air filter housing),
- the air inlet pipe
- the accelerator cable
- the feeds for the heater plugs ,
- the connector of the injector with sensor,
along with the fast idle solenoid valve connec-
tor (5),
- the fuel supply and return unions at (A) and
(B).
Disconnect connector (6) from the diesel fuel fil-
ter, remove it from its support and move the die-
sel fuel filter pipe assembly to one side. Place bracket Mot. 1159 at the mounting of the
coolant pipe on the cylinder block, then remove
the engine support tool.
99310R
F8Q Engine
11-24

FUEL MIXTURE
Specifications
12
DESCRIPTIONMAKE/TYPESPECIAL NOTES
Computer SAGEM or
MAGNÉTI MARÉLLI
35 tracks on manual gearbox vehicles without option
55 tracks on air conditioning vehicles
Injection - Multipoint with semi-sequential regulation
Ignition
-Static with 2 dual output
monobloc coils
Power module integral
in computer
One pinking sensor
tightening torque : 2.5 daN.m
TDC sensor - Resistance 220 Ω
Plugs
EYQUEM : RFC50LZ2E
NGK : BKR5EKGap: 0.9 mm
Tightening torque: 2.5 to 3 daN.m
Fuel filter - Mounted under vehicle in front of fuel tank
Replaced during major service
Fuel pump
WALBROSubmerged in fuel tank
Flow: at least 80 litres/hour at a regulated pressure
of 3 bars and a voltage of 12 V
Pressure regulator
-Regulated pressure
Zero vacuum :3 ± 0.2 bars
Vacuum of 500 mbars :2.5 ± 0.2 bars
Solenoid injectors
SIEMENSVoltage:12 Volts
Resistance :14.5 ± 1 Ω
Tracks Resistance
1 - 2 1.5 Ω
1
- 4 |1 - 3
2 -3 | 2 - 41 Ω
3 - 4 0.6 Ω
HT - HT8 KΩ
D7F engine
12-2

FUEL MIXTURE
Specifications
12
DESCRIPTIONMAKE/TYPESPECIAL NOTES
ComputerSIEMENS
FENIX 555tracks
Injection - Multipoint with semi-sequential regulation
Ignition
-Static with 2 dual output
monobloc coils
Power module integral
in computer
One pinking sensor
tightening torque : 2.5 daN.m
TDC sensor - Resistance 220 Ω
Plugs
EYQUEM : RFC52LS
CHAMPION
: RC10PYC
Gap: 0.9 mm
Tightening torque: 2.5 to 3 daN.m
Fuel filter - Mounted under vehicle in front of fuel tank
Replaced during major service
Fuel pump
WALBROSubmerged in fuel tank
Flow: at least 80 litres/hour at a regulated pressure
of 3 bars and a voltage of 12 V
Pressure regulator
-
Regulated pressure
Zero vacuum :3 ± 0.2 bars
Vacuum of 500 mbars :2.5 ± 0.2 bars
Solenoid injectors
SIEMENSVoltage:12 Volts
Resistance :14.5 ± 1 Ω
Tracks Resistance
1 - 2 0.5 Ω
1 - 3
2 -31 Ω
HT - HT10 KΩ
E7J engine
12-5

FUEL MIXTURE
Throttle body
12
Throttle body mounting bolt 1
TIGHTENING TORQUES (in daN.m)
REMOVAL
Disconnect the battery.
Remove the air filter.
Remove the air intake pipe (1).
Disconnect:
- the accelerator cable,
- the connectors :
• of the stepping motor (2),
• of the throttle potentiometer (3).
E7J engine
Remove the four throttle body mounting bolts (5)
and remove the throttle body.
REFITTING
Replace the throttle body seal.
Refitting is then the reverse of removal.
13339R113338R
12-8

FUEL MIXTURE
Inlet manifold
12
Inlet manifold bolt and nut 2
TIGHTENING TORQUES (in daN.m)
REMOVAL
Remove:
- the air filter,
- the injector gallery (see section 13).
Lift the vehicle.
Remove the strut (1) (to gain access to the bolt
fixing the strut on the right-hand side of the vehi-
cle, remove the mudguard and the right-hand
wheel).
E7J engine
13339R2
Disconnect the accelerator cable and the electrical
connectors (2) connected to the throttle body.
Remove the bolts and nuts (3) securing the mani-
fold. Lower the vehicle.
Remove the air intake pipe (A) connecting the
throttle body to the air filter.
13335-1R
13130R
12-10

FUEL MIXTURE
Inlet/Exhaust manifolds
12F8Q engine
Manifold mounting studs on cylinder head 1
Manifold mounting nuts on cylinder head 2.7
Inlet manifold strut mounting bolt 2.5
Cylinder block strut mounting bolt 2.5
TIGHTENING TORQUES (in daN.m)
REMOVAL
Remove the air filter (two mounting bolts at the
top, two mounting nuts at the bottom (1)).
Remove, from above, the two nuts fixing the ex-
haust downpipe to the manifold.
Slacken, without removing it, the nut on the
clamp connecting the downpipe to the exhaust
pipe.
Tilt the exhaust downpipe towards the gearbox.
Remove the nuts securing the manifolds:
- nuts (A) from above,
- nuts (B) from below.
PRO12.1
Special note
To remove nut (C) located above the starter mo-
tor, use a small ratchet (6.35 mm square) and a
universal joint.
13047-1R1
13047R
12-14

FUEL MIXTURE
Inlet/exhaust manifolds
12F8Q engine
REFITTING
Replace the manifold gaskets (metal part of the
gasket on the manifold side).
Replace the gaskets between the inlet manifold
and the air filter.
Replace the steel gasket between the exhaust ma-
nifold and the exhaust downpipe.
For the other operations, refitting is the reverse of
removal.
12-15