oil RENAULT KANGOO 1997 KC / 1.G Engine And Peripherals Workshop Manual

Contents
Consumables
Identification
Oil consumption
Oil pressure
Engine - Gearbox
Engine and transmission assembly
Sump
Crankshaft seal, timing end
Oil pump10-1
10-1
10-2
10-3
10-4
10-9
10-25
10-29
10-30
TOP AND FRONT OF ENGINE
Timing belt
Cylinder head gasket
Replacement of valve adjustersPage Page
11
Engine and
peripherals
11-1
11-11
11-29 ENGINE AND PERIPHERALS
10FUEL SUPPLY -
DIESEL EQUIPMENT
Fuel supply
Fuel cut off in case of an impact
Injector gallery
Fuel filter
Pump flow
Fuel pressure
Antipercolation device
Diesel equipment
General
Specifications
Location of components
Advance solenoid valve
Altimetric corrector
Fast idle LDA
Coded solenoid valve
Load potentiometer
Computer configuration
Injector with sensor (needle
lift)
Injection warning light
Pre-postheating control
Fast idle control
Injection/air conditioning
programming
Computer
Defect modes
Pump
Pump -Timing
Idle speed settings13-1
13-2
13-6
13-7
13-8
13-12
13-13
13-14
13-16
13-19
13-22
13-25
13-26
13-28
13-29
13-31
13-32
13-33
13-35
13-36
13-36
13-37
13-38
13-39
13-41
13-4613
FUEL MIXTURE
Specifications
Throttle body
Inlet manifold
Exhaust manifold
Inlet-exhaust manifolds12-1
12-7
12-15
12-18
12-2012

Page
Cooling
Specifications
Filling and bleeding
Testing
Diagram
Water pump
Exhaust
General
Exhaust pipe assembly
Fuel tank
Tank
Sender unit
Pump and sender unit assembly
Engine suspension
Suspended engine mountings19-1
19-2
19-3
19-4
19-7
19-12
19-15
19-17
19-29
19-30
19-32 COOLING - EXHAUST - FUEL TANK -
ENGINE SUSPENSION
19
16-1
16-7 STARTING - CHARGING
Alternator
Starter
16
IGNITION - INJECTION
Ignition
Static ignition
Plugs
Injection
General
Location of components
Centralised coolant temperature
management
Injection fault warning light
Immobiliser function
Computer configuration depending
on gearbox type17
14-1
14-2
14-7
14-11 ANTIPOLLUTION
Test for the presence of lead
Fuel vapour rebreathing
Oil vapour rebreathing
Exhaust gas recirculation
(EGR)
14
17-17
17-18
17-19
17-20
17-22 IGNITION - INJECTION
(continued)
Injection/air conditioning
programming
Idle speed correction
Adaptive idle speed
correction
Richness regulation
Adaptive richness correction
17
Page
17-1
17-3
17-4
17-8
17-13
17-14
17-15
17-16
Contents

ENGINE AND ENGINE PERIPHERALS
Oil consumption
10
OIL CONSUMPTION MEASUREMENT PROCEDURE
a) Filling to the maximum level
The operation must be carried out with the engine hot (one rotation of the cooling fan assembly) and af-
ter settling for 15 minutes to allow all the oil to drain into the sump.
Check visually using the dipstick.
Top up to the maximum level.
Seal the drain plug (with a paint mark on both the filler plug and the sump’s drain plug) in order to be
able to check later that it has not been removed.
b) Customer driving
Ask the customer to drive the vehicle for a period corresponding to about 1250 miles (2,000 km) or before
the minimum level is reached.
c) Refilling to the maximum level
The operation must be carried out with the engine hot (one rotation of the cooling fan assembly) and af-
ter a settling time of 15 minutes.
Check visually using the dipstick.
Top up to the maximum level.
Note the quantity of oil and the mileage covered since the last filling to the maximum level.
d) Measurement of the oil consumption
Quantity of topping up oil (in litres)
OIL CONSUMPTION =----------------------------------------
km (in thousands)
10-2

87363R1
ENGINE AND ENGINE PERIPHERALS
Oil pressure
10
SPECIAL TOOLING REQUIRED
Mot. 836 -05 Oil pressure measuring kit
EQUIPMENT REQUIRED
22 mm long socket
CHECKING
The oil pressure should be checked when the en-
gine is warm (approximately 80°C).
Contents of kit Mot. 836-05.
USE
ENGINE CHECKING
D engine
Idling0.8 bar
4 000 rpm3.5 bars
E engine
Idling1 bar
3 000 rpm3 bars
F engine
1 000 rpm1.2 bars
3 000 rpm3.5 bars
D engine E engine F engine
C + F C + E + F B + F
10-3

ENGINE AND ENGINE PERIPHERALS
Engine - Gearbox
10
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect:
- the battery,
- the electrical connectors from the engine
connection unit and its environment.
13034S
Drain:
- the cooling circuit (bottom hose of the
radiator),
- the gearbox oil,
- the engine oil if necessary.
Remove:
- the battery,
- the bonnet,
- the wheels,
- the air intake pipe,
- the expansion bottle and fix it to the engine. Brake caliper guide bolt 4
Shock absorber base bolts 18
Driveshaft gaiter mounting bolt 2.5
Wheel bolt 9
Left-hand suspended mounting bolt
on gearbox 6.2
Left-hand suspended mounting bolt
and nut on body 2.1
Right hand suspended
engine mounting bolt on engine 6.2
Right hand suspended
engine mounting bolt on body 6.2
TIGHTENING TORQUES (in daN.m)
D7F engine
SPECIAL TOOLING REQUIRED
B. Vi. 31-01 Set of three punches for roll
pins
Mot. 1202 Hose clip pliers
Mot. 1273 Tool for checking belt tension
Mot. 1311-06 Tool for removal of fuel pipe
Mot. 1379 Tool for retaining engine on
sub-frame
T. Av. 476 Ball joint extractor
EQUIPMENT REQUIRED
Load positioner
10-4

ENGINE AND ENGINE PERIPHERALS
Engine - Gearbox
10
12924R3
Apply Rhodorseal 5661 to the driveshaft roll pin hole.
Press the brake pedal several times to bring the pistons into contact with the brake pads.
Refit the power assisted steering pump belt (see section 07).
Fill:
- the gearbox with oil,
- the engine with oil (if necessary),
- the cooling circuit and bleed it (see section 19).
REFITTING (special notes)
Refitting is the reverse of removal.
Tighten the suspended engine mounting bolts to the recommended torque.
NOTE : tighten the suspended engine mounting bolts on the body in the order recommended below:
-1⇒bolt A to a torque of 2.1 daNm.
-2⇒bolt B to a torque of 2.1 daNm.
-3⇒bolt C to a torque of 2.1 daNm. D7F engine
10-8

ENGINE AND ENGINE PERIPHERALS
Engine and transmission assembly
10
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect:
- the battery,
- the electrical connectors from the engine
connection unit and its environment.
13034S
Drain:
- the cooling circuit (disconnect the bottom
hose of the radiator),
- the gearbox oil if necessary,
- the engine oil if necessary.
Remove:
- the battery,
- the wheels,
- the air intake pipe,
- the upper radiator mountings,
- the expansion bottle and fix it to the engine,
- the power assisted steering fluid reservoir,
and secure it onto the engine. Shock absorber base bolts 18
Track rod end 3.7
Front sub-frame mounting bolt 6.2
Rear sub-frame mounting bolt 10.5
Driveshaft gaiter mounting bolt 2.5
Wheel bolt 9
Mounting nut for rubber engine mounting
pad on left suspended engine mounting 6.2
Mounting bolt for front right suspended
engine mounting on the engine 6.2
Mounting bolt for front right suspended
engine mounting on the body 6.2
Steering shaft yoke bolt 2.5
TIGHTENING TORQUES (in daN.m)
D7F engine
SPECIAL TOOLING REQUIRED
B. Vi. 31-01 Set of punches for roll pins
Mot. 1040-01 Dummy sub-frame for
removing and refitting engine
and transmission assembly
Mot. 1202 Hose clip pliers
Mot. 1311-06 Tool for removal of fuel pipe
Mot. 1379 Tool for retaining engine on
sub-frame
T. Av. 476 Ball joint extractor
T. Av. 1233-01 Tool for sub-frame and axle
assembly
10-9

ENGINE AND ENGINE PERIPHERALS
Engine and transmission assembly
10
12924R4
Apply Rhodorseal 5661 to the driveshaft roll pin hole.
Press the brake pedal several times to bring the pistons into contact with the brake pads.
Fill:
- the gearbox with oil (if necessary),
- the engine with oil (if necessary),
- the cooling circuit and bleed it (see section 19).
REFITTING (special notes)
Use tool T. Av. 1233-01 to position the engine and transmission assembly in relation to the body.
Refitting is the reverse of removal.
Tighten the suspended engine mounting bolts and nuts to the recommended torque.D7F engine
10-13

ENGINE AND ENGINE PERIPHERALS
Engine and transmission assembly
10
REFITTING
The alignment of the sub-frame with the body
will be made easier by positioning two threaded
rods Mot. 1233-01 in the two front mountings of
the sub-frame on the body.
Tighten the sub-frame mounting bolts to a torque
of:
- 6.2 daN.m at the front,
-10.5 daN.m at the rear.
Refitting is the reverse of removal.
Fit the heat shields correctly.
Apply
Loctite FRENBLOC to the caliper mounting
bolts and tighten them to the recommended tor-
que.
Press the brake pedal several times to bring the
pistons into contact with the brake pads.
Fill:
- the engine and gearbox with oil, if necessary,
- the cooling circuit and bleed it (see section 19
"Filling - bleeding"). E7J engine
Fix tool Mot. 1040-01 underneath the sub-frame.
98755R1
Lower the lift until the tool touches the ground.
Remove the sub-frame mounting bolts and take
out the engine and transmission assembly by lif-
ting the body.
NOTE : for any operation requiring separation of
the engine, gearbox and sub-frame assembly,
take care to mark the position of Mot. 1159 on the
sub-frame.
10-18

ENGINE AND ENGINE PERIPHERALS
Engine and transmission assembly
10
REFITTING
The alignment of the sub-frame with the body
will be made easier by positioning two threaded
rods Mot. 1233-01 in the two front mountings of
the sub-frame on the body.
Tighten the sub-frame mounting bolts to a torque
of:
- 6.2 daN.m at the front,
-10.5 daN.m at the rear.
Refitting is the reverse of removal.
Fit the heat shields correctly.
Apply
Loctite FRENBLOC to the caliper mounting
bolts and tighten them to the recommended tor-
que.
Press the brake pedal several times to bring the
pistons into contact with the brake pads.
Fill:
- the engine and gearbox with oil, if necessary,
- the cooling circuit and bleed it (see section 19
"Filling - bleeding"). F8Q engine
Fix tool Mot. 1040-01 underneath the sub-frame.
98755R1
Lower the lift until the tool touches the ground.
Remove the sub-frame mounting bolts and take
out the engine and transmission assembly by lif-
ting the body.
NOTE : for any operation requiring separation of
the engine, gearbox and sub-frame assembly,
take care to mark the position of Mot. 1159 on the
sub-frame.
Remove the mounting bolts (3).
12993-1R3
10-24