lock RENAULT KANGOO 1997 KC / 1.G Foult Finding - Injection Owner's Guide

1EC761.0
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Interpretation of XR25 bargraphs
Bargraph 8 left hand side illuminated Fiche n° 49
Resistance on driver’s pretensioner line
XR25 aid :*08 : CC : Short circuit
CO : Open circuit
8
Never carry out measurements on the trigger lines with equipment other than the
XRBAG.NOTES
Lock the computer using command G80* on the XR25.
Switch off the ignition and check ignition module of the driver’s pretensioner is correctly connected.
Disconnect the ignition module of the driver’s pretensioner and connect a dummy ignition module to
the ignition module connector.
Switch on the ignition and carry out an XR25 check.
Replace the driver’s pretensioner if the fault has been memorised (fault no longer declared).
Disconnect the computer connector and fit the 30 track adaptor.
The XRBAG tool MUST be used for checking resistance on the wire marked E of the adaptor .
If the value obtained is not correct , check the 30 track connector connection (tracks 1 and 2) and replace
the wiring if necessary.
If the checks carried out have not proven the existence of a fault, replace the airbag computer (consult
the section "Aid" for this operation).
Reconnect the ignition module of the driver’s pretensioner .
The XRBAG tool MUST be used for checking resistance at point C1 (seat connector) on the line of the
driver’s pretensioner .
If the value obtained is not correct , replace the wiring between points C1 and C3 (seat wiring).
Erase the computer memory using the command G0** then switch off the ignition.
Carry out another XR25 check and if there is no fault, unlock the computer using
command G81*.
Destroy the pretensioner if it has been replaced (tool Elé. 1287).
AFTER REPAIR
88
88-14

1EC761.0
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Interpretation of XR25 bargraphs
Bargraph 8 right hand side illuminated Fiche n° 49
Resistance on the passenger’s pretensioner line
XR25 aid :*28 : CC : Short circuit
CO : Open circuit
8
Never carry out measurements on the trigger lines with equipment other than the
XRBAG.NOTES
Lock the computer using command G80* on the XR25.
Switch off the ignition and check that the ignition module of the passenger’s pretensioner is correctly
connected.
Disconnect the ignition module of the passenger’s pretensioner and connect a dummy ignition module
to the ignition module connector.
Switch on the ignition and carry out an XR25 check.
Replace the passenger’s pretensioner if the fault has been memorised (fault no longer declared).
Disconnect the computer connector and fit the 30 track adaptor.
The XRBAG tool MUST be used for checking resistance on the wire marked D on the adaptor.
If the value obtained is not correct , check the 30 track connector connection (tracks 3 and 4) and replace
the wiring if necessary.
If the checks carried out have not proven the existence of a fault, replace the airbag computer (consult
the section "Aid" for this operation).
Reconnect the ignition module of the passenger’s pretensioner .
The XRBAG tool MUST be used for checking resistance at point C1 (seat connector) of the passenger’s
pretensioner line.
If the value obtained is not correct , replace the wiring between points C1 and C3 (seat wiring).
Erase the computer memory using the command G0** then switch off the ignition.
Carry out another XR25 check and if there is no fault, unlock the computer using
command G81*.
Destroy the pretensioner if it has been replaced (tool Elé. 1287).
AFTER REPAIR
88
88-15

1EC761.0
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Interpretation of XR25 bargraphs
Bargraph 9 right hand side illuminated Fiche n° 49
Insulation of pretensioner lines
XR25 aid :*29 : CC.1 : Short circuit at 12 volts
CC.0 : Short circuit to earth
9
Never carry out measurements on the trigger lines with equipment other than the
XRBAG.NOTES
Lock the computer using command G80* on the XR25.
Disconnect the ignition module of the driver’s pretensioner and connect a dummy ignition module to
the ignition module connectors.
Switch on the ignition and carry out an XR25 check.
If the fault has been memorised (fault no longer declared), check the condition of the seat wiring.
Replace the driver’s pretensioner if the wiring is not faulty.
Then carry out the same operation on the Passenger’s pretensioner (if not a driver’s side fault ).
The XRBAG tool MUST be used for measuring insulation appropriate to the type of fault at point C1 (seat
connector) of the driver’s pretensioner line.
If the value obtained is not correct , replace the wiring between points C1 and C3 (seat wiring).
Then carry out the same measurement on the passenger’s pretensioner line (if not a driver’s side fault ).
Disconnect the computer connector and fit the 30 track adaptor.
The XRBAG tool MUST be used for measuring insulation appropriate to the type of fault on the adaptor
wires marked D (Passenger ) and E (Driver ) .
If one of the values obtained is not correct, check the 30 track connector connection (tracks 3 / 4 for wire
D and 1/2 for wire E) and replace the wiring if necessary .
If the checks carried out have not proven the existence of a fault, replace the airbag computer (consult
the section "Aid" for this operation).
Reconnect the ignition modules of the seat belt pretensioners.
Erase the computer memory using the command G0** then switch off the ignition.
Carry out another XR25 check and if there is no fault, unlock the computer using
command G81*.
Destroy the pretensioner(s) if it has been replaced (tool Elé. 1287).
AFTER REPAIR
88
88-16

1EC761.0
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Interpretation of XR25 bargraphs
Bargraph 10 left hand side illuminated Fiche n° 49
Short circuit or insulation from 12 volts on the warning light line 10
Use the 30 track XRBAG adaptor to operate on the computer connector .NOTES
If the checks carried out have not proven the existence of a fault, replace the airbag computer (consult
the section "Aid" for this operation).
Lock the computer using command G80* on the XR25.
Check the condition of the warning light bulb .
Ensure insulation
from 12 volts of the connection between the warning light and track 8 of the 30 track
connector.
Erase the computer memory using the command G0** then switch off the ignition
Carry out another XR25 check and if there is no fault, unlock the computer using
command G81*.AFTER REPAIR
88
88-17

1EC761.0
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Interpretation of XR25 bargraphs
Bargraph 10 right hand side illuminated Fiche n° 49
Open circuit or insulation from earth on the warning light line10
Use the 30 track XRBAG adaptor to carry out operations on the computer
connector .NOTES
Warning light extinguished
after ignition
Lock the computer using command G80* on the XR25.
Check the condition of the warning light bulb.
Ensure the continuity of the connection between the warning light and track 8 of the 30 track
connector.
Ensure that 12 volts are reaching the warning light .
If the checks carried out have not proven the existence of a fault, disconnect the computer connector and
fit the 30 track XRBAG adaptor . Use the XRBAG in testing mode to check the operation of the warning
light on the instrument panel from the grey adaptor wire.
If it is possible to illuminate the warning light using the XRBAG, replace the airbag computer (consult
the section "Aid" for this operation).
If it is impossible to operate the warning light , repeat the preceding checks.
NoneNOTES Warning light illuminated
after ignition
Lock the computer using command G80* on the XR25.
Ensure the insulation from earth of the connection between the warning light and track 8 of the 30 track
connector .
If the checks carried out have not proven the existence of a fault, replace the airbag computer (consult
the section "Aid" for this operation).
None
Erase the computer memory using the command G0** then switch off the
ignition. Carry out another XR25 check and if there is no fault, unlock the
computer using command G81*.AFTER REPAIR
88
NOTES
88-18

1EC761.0
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Interpretation of XR25 bargraphs
Bargraph 14 left hand side Fiche n° 49
Computer locked 14
NoneNOTES
This bargraph 14 left hand side allows computer locked status to be seen .
When it is illuminated, all trigger lines are inhibited, preventing the release of the airbags and the seat
belt pretensioners.
This bargraph is normally illuminated in two situations :
- The computer is new (it is sold in locked mode).
- The XR25 computer locking command has been used during an operation on the vehicle
(G80*).
Erase the computer memory using the command G0** then switch off the
ignition. Carry out another XR25 check and if there is no fault, unlock the
computer using command G81*.AFTER REPAIR
88
88-19

1EC761.0
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Interpretation of XR25 bargraphs
Bargraph 14 right hand side Fiche n° 49
Fault present before impact 14
NoneNOTES
This bargraph is normally illuminated in the following situations :
- An impact has been detected.
- A fault was present in the computer memory before the impact.
- This fault was declared by the illumination of the fault warning light before the impact .
Bargraph 14 left hand side can in this way justify non-release of an airbag or a seat belt pretensioner .
Consult the Techline if this bargraph is illuminated in other situations (no fault, no impact, ...).
Erase the computer memory using the command G0** then switch off the ignition
Carry out another XR25 check and if there is no fault, unlock the computer using
command G81*.AFTER REPAIR
88
88-20

1EC761.0
AIRBAG - SEAT BELT PRETENSIONERS
Fault finding - Aid
REPLACING THE AIRBAG COMPUTER
The airbag computers are sold in locked mode to avoid all risk of release at the wrong time (all
trigger lines are inhibited). This operational mode is indicated by the illumination of the warning
light on the instrument panel.
When replacing the airbag computer, follow this procedure :
- Ensure that the ignition is switched off.
- Replace the computer.
- Carry out an XR25 check.
- Unlock the computer using command G81*, only when no fault is declared.
88
88-24