check engine RENAULT KANGOO 1997 KC / 1.G General Information Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 1997, Model line: KANGOO, Model: RENAULT KANGOO 1997 KC / 1.GPages: 37
Page 3 of 37

TOWING
All types
Contents
SPECIFICATIONS
Engine - Clutch - Gearbox
Vehicle identification
01-1
01-2
LIFTING
Trolley jack - Axle stands
Underbody lifts
Page
01
02
03
General
vehicle
02-1
02-2
03-1
LUBRICANTS CONSUMABLES
Packaging
04-1
DRAINING FILLING
Engine
Gearbox
Power assisted steering
04
05
05-1
05-3
05-4
VALUES AND SETTINGS
Dimensions
Capacity - Grades
Belt tension
Accessories belt tension
Timing belt tension
Tightening the cylinder head
Tyres and wheels
Brakes
Brake limiter
Underbody heights
Values for checking the front axle
geometry
Values for checking the rear axle
geometry07
07-1
07-2
07-5
07-7
07-11
07-12
07-14
07-15
07-16
07-17
07-20
07-21
Page
Page 16 of 37

DRAINING - FILLING
Power assisted steering
05
CHECKING THE LEVEL
POWER ASSISTED STEERING PUMP LEVEL
For topping up or filling, use ELF RENAULTMATIC
D2 or MOBIL ATF 220 oil
.
The level, when correct, should be visible between
the
MIN and MAX marks on the reservoir (1).
D7F - E7J - F8Q ENGINES
12422R1
05-4
Page 18 of 37

VALUES AND SETTINGS
Capacity - Grades
07
Components
When
draining
3,5
3.7 (1)
2.7
2.9 (1)E.E.C. country
Other countries
Capacity
in litres
(approx.)*
Grade
Petrol engine
(oil)
D7F
E7J
0 °C+30 °C-30 °C
+10 °C+20 °C-20 °C-10 °C
-15 °C+25 °C
CCMC-G415W40-15W50
ACEA A2-96/A3-9615W40-15W50
CCMC-G510W30-10W40-10W50
ACEA A2-96/A3-96 10W30-10W40-10W50
CCMC-G55W30
ACEA A2-96/A3-965W30
CCMC-G55W40-5W50
ACEA A2-96/A3-965W40-5W50
API SH 10W40
API SH 10W30
0 °C+30 °C-30 °C+10 °C+20 °C-20 °C-10 °C
-15 °C
API SH 5W30
API SH 15W40
* Check with dipstick
(1) After replacing the oil filter
07-2
Page 19 of 37

VALUES AND SETTINGS
Capacity - Grades
07
When
draining
4.7
5.2 (1)E.E.C. country
Other countries
Diesel engine
(oil)
F8Q
0 °C+30 °C-30 °C
+10 °C+20 °C-20 °C-10 °C
-15 °C+25 °C
CCMC-PD215W40
ACEA B2-96/B3-9615W40
CCMC-PD210W40
ACEA B2-96/B3-9610W40
CCMC-PD25W30
ACEA B2-96/B3-965W30
CCMC-PD25W40
ACEA B2-96/B3-965W40
API CF 10W30
0 °C+30 °C-30 °C+10 °C+20 °C-20 °C-10 °C
-15 °C+15 °C
API CF 15W40
API CF 10W40
* Check with dipstick
(1) After replacing the oil filter
Components
Capacity
in litres
(approx.)*
Grade
07-3
Page 23 of 37

VALUES AND SETTINGS
Accessories belt tension
07
RIBBED BELT
Tensioning process
Engine cold (ambient temperature).
Fit the new belt.
Position the sensor of Mot. 1273.
Turn the wheel of the sensor until it disengages (three "CLICKS").
Tension the belt until the recommended fitting value is displayed on Mot. 1273 .
Lock the tensioner, check it, adjust the value.
Turn the crankshaft over three times.
Check that the tension value is within the fitting tension tolerance, otherwise readjust it.
NOTE :
Never refit a belt which has been removed.
Replace the belt if the tension is below the minimum operating tension.
Small cuts or cracks do not mean that the belt has to be replaced.
07-7
Page 24 of 37

VALUES AND SETTINGS
Accessories belt tension
07
10071R2
A Crankshaft
B Alternator
C Power assisted steering pump
T Tensioner
→Point for checking belt tension
ALTERNATOR BELT
D7F
ENGINE
Tension
(US=SEEM unit)Alternator
belt,
multitoothPower assisted
steering belt,
multitooth
Fitting102 ± 7 96 ± 5
Minimum
operating53 43
POWER ASSISTED STEERING BELT
SPECIAL TOOLING REQUIRED
Mot. 1273 Tool for checking the belt tension
97267R4
07-8
Page 25 of 37

VALUES AND SETTINGS
Accessories belt tension
07
13511R
A Crankshaft
B Alternator
C Power assisted steering pump
T Tension wheel
→Point for checking belt tension
ALTERNATOR BELT
E7J
ENGINE
Tension
(US=SEEM unit)Alternator
belt,
multitoothPower assisted
steering belt,
multitooth
Fitting101 ± 6 106 ± 6
Minimum
operating52 59
SPECIAL TOOLING REQUIRED
Mot. 1273 Tool for checking the belt tension
13510R
Bolt A: alternator belt tension
Bolt B: power assisted steering belt tension
NOTE : Tighten the nuts of bolts (A) and (B) after
adjusting the tension.
13363R1
POWER ASSISTED STEERING BELT
07-9
Page 26 of 37

VALUES AND SETTINGS
Accessories belt tension
07
13512R
A Crankshaft
B Alternator
C Power assisted steering pump
T Tension wheel
→Point for checking belt tension
ALTERNATOR BELT
F8Q
ENGINE
Tension
(US=SEEM unit)Alternator
belt,
multitoothPower assisted
steering belt,
multitooth
Fitting115 ± 5 116 ± 6
Minimum
operating70 68
SPECIAL TOOLING REQUIRED
Mot. 1273 Tool for checking the belt tension
13509R
ALTERNATOR AND POWER ASSISTED STEERING
BELT
07-10
Page 27 of 37

VALUES AND SETTINGS
Timing belt tension
07
13361R
E7J engine Tensioning process
Engine cold (ambient temperature).
Fit the new belt.
Position the sensor of Mot. 1273.
Turn the wheel of the sensor until it disengages
(three "CLICKS").
Tension the belt until the recommended fitting
value is displayed on Mot. 1273.
Lock the tensioner, check it and adjust the value.
Turn the crankshaft over at least three times .
Check that the tension value is within the fitting
tension tolerance (± 10%), otherwise readjust it,
repeating the operations described above.
NOTE :
- For the F8Q engine, remove the pin Mot 1054
before fitting the sensor of tool Mot 1273 and
press hard on the section of belt between the
intermediate shaft sprocket (or idle sprocket)
and the tension wheel, then make the measu-
rement.
- Never refit a belt which has been removed.
- Replace the belt if the tension is below the mi-
nimum operating tension.
D7F engine
There are special features for tensioning the ti-
ming belt: refer to section 11.
Belt tension (in SEEM units)
Fitting: 30 U.S.
Minimum operating : 26 U.S.
F8Q engine
13094R
Belt tension (in SEEM units)
Fitting : 29 U.S.
Minimum operating : 25 U.S.
07-11