lock RENAULT KANGOO 1997 KC / 1.G General Information Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 1997, Model line: KANGOO, Model: RENAULT KANGOO 1997 KC / 1.GPages: 37
Page 11 of 37
DESCRIPTIONPACKAGINGPART NUMBER
24 cc bottle
24 cc bottle
24 cc bottle
50 cc bottle77 01 394 070
77 01 394 071
77 01 394 072
77 01 400 309
ADHESIVES
LUBRICANTS CONSUMABLES
Packaging
04
•"LOCTITE - FRENETANCH"
stops bolts slackening and allows them to be
released
•
"LOCTITE - FRENBLOC"
locks bolts
•
"LOCTITE SCELBLOC"
for bonding bearings
•
"LOCTITE AUTOFORM"
for bonding the flywheel to the crankshaft
LUBRICANT CLEANING AGENTS
150 g aerosol
300 ml aerosol
355 ml can
500 ml aerosol
Aerosol
400 ml aerosol77 01 408 464
77 11 171 437
77 01 423 189
77 01 408 466
77 01 405 952
77 11 170 801•"NETELEC"
unseizes, lubricates
• Carburettor cleaner
• Injector cleaner
•Super-concentrated unseizing agent
•
"DECAPJOINT " (FRAMET) for cleaning the
gasket faces of aluminium cylinder heads
• Brake cleaner
MECHANICAL SEALANTS
77 01 422 750
77 01 421 162
77 11 143 071100 g tube
24 ml syringe
Aerosol• AUTO joint grey
sealing paste
•
LOCTITE 518
for sealing the gearbox housing
• Leak detector
04-2
Page 23 of 37
VALUES AND SETTINGS
Accessories belt tension
07
RIBBED BELT
Tensioning process
Engine cold (ambient temperature).
Fit the new belt.
Position the sensor of Mot. 1273.
Turn the wheel of the sensor until it disengages (three "CLICKS").
Tension the belt until the recommended fitting value is displayed on Mot. 1273 .
Lock the tensioner, check it, adjust the value.
Turn the crankshaft over three times.
Check that the tension value is within the fitting tension tolerance, otherwise readjust it.
NOTE :
Never refit a belt which has been removed.
Replace the belt if the tension is below the minimum operating tension.
Small cuts or cracks do not mean that the belt has to be replaced.
07-7
Page 27 of 37
VALUES AND SETTINGS
Timing belt tension
07
13361R
E7J engine Tensioning process
Engine cold (ambient temperature).
Fit the new belt.
Position the sensor of Mot. 1273.
Turn the wheel of the sensor until it disengages
(three "CLICKS").
Tension the belt until the recommended fitting
value is displayed on Mot. 1273.
Lock the tensioner, check it and adjust the value.
Turn the crankshaft over at least three times .
Check that the tension value is within the fitting
tension tolerance (± 10%), otherwise readjust it,
repeating the operations described above.
NOTE :
- For the F8Q engine, remove the pin Mot 1054
before fitting the sensor of tool Mot 1273 and
press hard on the section of belt between the
intermediate shaft sprocket (or idle sprocket)
and the tension wheel, then make the measu-
rement.
- Never refit a belt which has been removed.
- Replace the belt if the tension is below the mi-
nimum operating tension.
D7F engine
There are special features for tensioning the ti-
ming belt: refer to section 11.
Belt tension (in SEEM units)
Fitting: 30 U.S.
Minimum operating : 26 U.S.
F8Q engine
13094R
Belt tension (in SEEM units)
Fitting : 29 U.S.
Minimum operating : 25 U.S.
07-11