engine RENAULT KANGOO 1997 KC / 1.G Sheet Metal Work User Guide

UPPER FRONT STRUCTURE
Cowl side panel (pillar lining), part section
42C
PRB4210
INTRODUCTION
The replacement of this part is a complementary
operation for a frontal impact to a headlight car-
rier panel.
It will be partially replaced according to the cut on
the diagram and the method below.
The replacement of this part also requires the re-
placement of the cowl side panel upper reinforce-
ments.
In the operation described below there are only
descriptions of joints specific to the part concer-
ned.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
1 - Cowl side panel , part assembled with :
- front wing mounting,
- impact retainer reinforcement (bonnet),
- dashboard mounting support,
- shock absorber cup height adjuster reinforce-
ment .
2 - Cowl side panel upper reinforcement, front
section.
3 - Cowl side panel upper reinforcement, rear
section.
JOINTS WITH :
Engine support plate
Shock absorber cup
Plenum chamber
PARTS CONCERNED (thickness in mm):
1Cowl side panel (pillar lining) 1.5
2Engine support plate 2
3Shock absorber cup 2
4Plenum chamber 1
5 Shock absorber cup height adjuster 1or
42-5

UPPER FRONT STRUCTURE
Cowl side panel upper reinforcement
42D
PRB4211
INTRODUCTION
The replacement of this part is complementary to
the headlight carrier panel for a frontal impact.
In the operation described below there are only
descriptions of joints specific to the part concer-
ned.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Parts only :
1 - Cowl side panel upper reinforcement, front
section.
2 - Cowl side panel upper reinforcement, rear
section.
PARTS CONCERNED (thickness in mm):
1Cowl side panel (pillar lining) 1
2Cowl side panel upper reinforcement,
front section 1
3Cowl side panel upper reinforcement,
rear section 1
4Engine support plate 2
5Shock absorber cup 2
6Shock absorber cup height adjuster 1
7Windscreen wiper mounting 1
8Front pillar 1.5
JOINTS WITH :
Cowl side panel (pillar lining)
Cowl side panel upper reinforcement, front
section
Cowl side panel upper reinforcement, rear
section
Front pillar
12892R
CAA11538R4
A
2 / 3
1
42-8

UPPER FRONT STRUCTURE
Wheel arch, front section
42E
PRB4212
INTRODUCTION
The replacement of this part is an operation for a
frontal impact and is complementary to the repla-
cement of the cowl side panel (pillar lining).
It can be carried out partially from the right hand
side (see diagram and method below).
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning other parts will be dealt
with in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
1 - Part only (right hand side).
2 - Part only (left hand side).
JOINTS WITH :
Engine mounting height adjuster (right hand side)
Shock absorber cup height adjuster
Side member closure panel
Front end lower cross member (right hand side)
Cowl side panel (pillar lining)
PARTS CONCERNED (thickness in mm):
1Engine mounting 2
2Shock absorber cup height adjuster 2
3Side member closure panel 1
4Side member, front section 1.5
5Front wheel arch 1
6Front end lower cross member 1.5
7Cowl side panel (pillar lining) 1.5
or
42-12

UPPER FRONT STRUCTURE
Wheel arch
42F
PRB4213
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the cowl side pa-
nel (pillar lining) for a frontal impact.
It also requires the replacement of the cowl side
panel upper reinforcements (pillar lining), and
the use of the repair bench.
In the operation below there are only descriptions
of the joints specific to the part concerned.
Information concerning other parts will be dealt
with in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with :
- engine mounting height adjuster (right hand
side),
- engine support plate (right hand side),
- wheel arch ,
- shock absorber cup ,
- shock absorber cup height adjuster ,
- ABS mounting (right hand side),
- injection unit and impact sensor mounting
(left hand side).
JOINTS WITH :
Plenum chamber
Side member closure panel
Front side member
Front end lower cross member
PARTS CONCERNED (thickness in mm):
1Shock absorber cup height adjuster 1
2Engine mounting height adjuster 1.5
3Engine mounting reinforcement 1.5
4Shock absorber cup 2
5Plenum chamber 1
6Side member closure panel 1
7Front side member, front section 1.5
8Front side member, rear section 2.5
9Front wheel arch 1
10Front end lower cross member 1.5
11Injection unit and impact sensor
mounting (left hand side) 2
42-17