sensor RENAULT KANGOO 2013 X61 / 2.G Diesel DCM 1.2 Injection User Guide

13B-27
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF002
CONTINUED
Check the insulation, continuity and the absence of interference resistance on the following connections:
●3B between components 120 and 799,
●3FB (or 3FBA) of component 799,
●NH of component 799.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Measure the resistance of the air flow sensor to ensure that it is between:
41255  < X < 47492  at - 40°C,
14260  < X < 16022  at - 20°C,
5497  < X < 6050  at 0°C,
2353  < X < 2544  at 20°C,
1114  < X < 1186  at 40°C,
569  < X < 597  at 60°C,
310  < X < 322  at 80°C,
180  < X < 185  at 100°C.
If the value is not correct, replace the air flow sensor (see MR388 (Logan/Sandero), MR451 (Duster),
Mechanical, 12A Fuel mixture, Air flowmeter: Removal – Refitting).
If the fault is still present, replace the air flowmeter (see MR388 (Logan/Sandero), MR451 (Duster), Mechanical,
12A Fuel mixture, Air flowmeter: Removal – Refitting).
If the fault is still present, contact the Techline.

13B-28
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF003
PRESENT
OR
STOREDATMOSPHERIC PRESSURE SENSOR CIRCUIT
CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to +12 V
NOTESSpecial notes:
The atmospheric pressure sensor is built into the injection computer.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Look for any wiring harness damage and check the condition and connection of the injection computer connectors,
component code 120.
Check the connection and condition of the injection locking relay connector.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Move the wiring harness between the injection computer and the battery, component code 107 to see if a change
of status occurs (Present  Stored).
Look for any damage to the wiring and check the connection and condition of the battery and its connections.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A (Renault) or Technical Note
9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace
the wiring.
Measure the battery voltage when the ignition is switched on.
If the battery voltage is less than 11 V, recharge the battery (see Technical Note 6014A (Renault) or Technical
Note 9859A (Dacia), Checking the charging circuit).
Check the condition and connection of the battery terminals and posts.
DCM1.2_V08_DF003

13B-29
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF005
PRESENT
OR
STOREDENGINE SPEED SENSOR CIRCUIT1.DEF: Inconsistency
2.DEF: Inconsistency
3.DEF: Too many additional teeth
4.DEF: Teeth missing
5.DEF: Additional teeth
6.DEF: Too many teeth missing
NOTESSpecial notes:
If fault DF005, 1.DEF, 2.DEF, 3.DEF or 6.DEF is present: the engine stops and the
level 2 warning light comes on.
If fault DF005, 4.DEF or 5.DEF is present: engine performance is reduced to 75%, and
no warning light comes on.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Conditions for applying the fault finding procedure to a stored fault:
The fault is present when the starter motor is operating or the engine is running at idle
speed.
Check the connection and condition of the engine speed sensor connector, component code 149.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check that the engine speed sensor is correctly fitted to the engine.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●3BL between components 120 and 149,
●3BG between components 120 and 149.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Measure the resistance of the engine speed sensor between connections 3BG and 3BL of component 149.
If the resistance of the engine speed sensor is not between 510  < X < 850  at 20°C, replace the sensor (see
MR 388 (Logan/Sandero) or MR 451 (Duster), MR 423 (Thalia 2/Symbol 2) or MR 374 (Kangoo VLL),
Mechanical, 13B Diesel injection, Crankshaft position sensor: Removal – Refitting).
Check that the flywheel ring gear is not defective (missing teeth).
If the fault is still present, contact the Techline.
DCM1.2_V08_DF005

13B-30
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF007
PRESENT
OR
STOREDRAIL PRESSURE SENSOR CIRCUITCC.0: Short circuit to earth
CO.1: Open circuit or short circuit to +12 V
1.DEF: Inconsistency
2.DEF: Below minimum threshold
3.DEF: Above maximum threshold
4.DEF: Value outside permitted tolerance
NOTESPriority when dealing with a number of faults:
– DF113 Sensor supply voltage.
Conditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine starts.
Special notes:
If fault DF007 is present, the engine stops and restarting is impossible.
Level 2 warning light comes on.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Check the connection and condition of the rail pressure sensor connector, component code 1032.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check for + 5 V on connection 3LX of the rail pressure sensor, component code 1032.
Check for earth on connection 3LZ of the rail pressure sensor, component code 1032.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●3LX between components 120 and 1032,
●3LY between components 120 and 1032,
●3LZ between components 120 and 1032.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If the fault is still present, the rail pressure sensor is faulty, replace the rail (see MR 388 (Logan/Sandero) or MR
451 (Duster), MR 423 (Thalia 2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 13B, Diesel injection,
Injector rail: Removal – Refitting).
DCM1.2_V08_DF007

13B-31
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF008
PRESENT
OR
STOREDPEDAL POTENTIOMETER CIRCUIT GANG 1CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to +12 V
1.DEF: Inconsistency between pedal gang 1 and gang 2
2.DEF: No signal
3.DEF: Jammed component
NOTESPriority when dealing with a number of faults:
– DF113 Sensor supply voltage.
Special notes:
If fault DF008 is present: the engine speed is maintained above 1000 rpm (normal idle
speed with the brake pedal depressed) and the level 1 warning light comes on
(except 3.DEF).
If faults DF008 and DF009 Pedal potentiometer circuit gang 2 are present: engine
speed fixed at 1300 rpm, level 1 warning light lit.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
1.DEF
3.DEF
NOTESNone.
Disconnect the injection computer connector, component code 120 and the pedal potentiometer connector,
component code 921.
Check the insulation, continuity and the absence of interference resistance of the following connections:
●3LS between components 120 and 921,
●3LW between components 120 and 921.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If the fault is still present, replace the pedal potentiometer (see MR 388 (Logan/Sandero), MR451 (Duster), MR
423 (Thalia 2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 37A, Mechanical component controls,
Accelerator pedal: Removal – Refitting).
If the fault is still present, contact the Techline.
DCM1.2_V08_DF008

13B-37
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF010
PRESENT
OR
STOREDEGR POSITION SENSOR CIRCUIT
1.DEF: At minimum limit
2.DEF: At maximum limit
NOTESPriority when dealing with a number of faults:
– DF113 Sensor supply voltage.
Special notes:
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
K9K 714, 718, 740, 792, 796 ENGINES (Euro 4):
Check the connection and condition of the EGR valve connectors, component code 1460.
Check the connection and condition of the computer connectors, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the insulation and continuity of the following connections:
●3GC between components 1460 and 120,
●3EL between components 1460 and 120,
●3JM between components 1460 and 120.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Check for + 5 V on connection 3GC of the EGR valve sensor, component code 1460.
Check for earth on connection 3JM of the EGR valve sensor, component code 1460.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
DCM1.2_V08_DF010

13B-38
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF010
CONTINUED 1
Measure the resistance of the EGR valve, component code 1460:
●with the engine stopped, the EGR valve will be closed (unless there is a fault),
●wait for the ambient temperature to stabilise (approximately 20°C) around the valve,
measure the resistance between connections 3VP and 3VQ of component 1460. The resistance must be between:
0.5  < R < 50 .
If the value is not correct, replace the EGR valve (see MR 388 (Logan/Sandero), MR 451 (Duster), MR 423
(Thalia 2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 14A, Emission control, Exhaust gas
recirculation solenoid valve: Removal – Refitting).
After replacing the EGR valve, use command RZ002 EGR adaptives to reinitialise the EGR valve offsets.
If the fault is still present, contact the Techline.
K9K 790, 794 ENGINE (euro 3):
Check the connection and condition of the EGR valve connector, component code 1460.
Check the connection and condition of connector B (brown 48-track) of the computer, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the insulation and continuity of the following connections:
●3GC between components 1460 and 120,
●3EL between components 1460 and 120,
●3JM between components 1460 and 120.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Check for + 5 V on connection 3GC of the EGR valve sensor, component code 1460.
Check for earth on connection 3JM of the EGR valve sensor, component code 1460.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.

13B-40
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF014
PRESENT
OR
STOREDVEHICLE SPEED SIGNAL CIRCUIT1.DEF: Inconsistency
2.DEF: No signal
3.DEF: Below minimum threshold
4.DEF: The multiplex line test has detected at least one fault
5.DEF: Dialogue disrupted
NOTESSpecial notes:
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Check the connection and condition of the speed sensor connector, component code 250 or of the ABS computer
connector, component code 118 or 1094 or of the front/rear torque distributor connector, component code 2017.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Connect the bornier in place of the computer and check the insulation, the continuity and the absence of
interference resistance on connection 47F of the injection computer, component code 120.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
If the fault is still present, replace the speed sensor.
DCM1.2_V08_DF014

13B-50
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF021
PRESENT
OR
STOREDPREHEATING WARNING LIGHT CIRCUIT
CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to + 12 V
NOTESSpecial notes:
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Clear the fault and check the correct operation of the warning light with command AC060 Preheating warning
light.
Check the connection and condition of the connector for the preheating warning light sensor, component code
247.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 9804A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation and continuity of the following connection:
•3NX between components 247 and 120.
If the connection is faulty and if there is a repair procedure (see Technical Note 9804A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the instrument panel, component code 247 (see MR 388, (Logan/Sandero), MR
423 (Thalia 2/Symbol 2), MR 451 (Duster) or MR 374 (Kangoo VLL), Mechanical, 83A, Instrument panel,
Instrument panel: Removal - Refitting).
If the fault persists, contact your Techline.
DCM1.2_V08_DF021

13B-51
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF022
PRESENT
OR
STOREDOBD WARNING LIGHT CIRCUIT
CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to + 12 V
NOTESSpecial notes:
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Clear the fault and check the correct operation of the warning light with command AC155 MIL warning light.
Check the connection and condition of the connector for the OBD warning light sensor, component code 247.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the insulation and continuity of the following connection:
•3FH or 137C between components 247 and 120.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
If the fault is still present, replace the instrument panel, component code 247 (see MR 388, (Logan/Sandero), MR
423 (Thalia 2/Symbol 2), MR 451 (Duster) or MR 374 (Kangoo VLL), Mechanical, 83A, Instrument panel,
Instrument panel: Removal - Refitting).
If the fault persists, contact your Techline.
DCM1.2_V08_DF022