fuel pressure RENAULT KANGOO 2013 X61 / 2.G Diesel DCM 1.2 Injection Owner's Guide

13B-191V1 MR-376-X76-13B000$160.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
TEST 6 High pressure system check
NOTESSpecial note:
Certain faults make it impossible to carry out this test - deal with these first.
WARNING
Running the starter motor for more than 5 seconds is dangerous and serves no useful
purpose.
Preliminary Checks:
– Check for the presence of fuel
– Check that there is no air in the low pressure circuit. Apply TEST 1 Low pressure circuit check.
– Ensure that the correct fuel is being used. Apply TEST 13 Diesel fuel conformity check.
The pump's capacity to produce high pressure can be checked by the following procedure:
–With the ignition off, disconnect the low pressure actuator from the pump (IMV brown connector) and
connect a test IMV or the MOT adapter. 1711 adapter.
– Electrically disconnect the four injectors.
– Switch on the ignition, connect the diagnostic tool and re-establish dialogue with the injection system.
– Go to the Main computer statuses and parameters screen.
– Run the test cold, PR064 "Coolant temperature" < 30 °C or equal to ambient temperature.
–Activate the starter for 5 seconds.
– Read the maximum rail pressure value PR038 Rail pressure during the test on the diagnostic tool.
PR038 > 1050 bar?
A
NO
B
YES
DCM1.2_V08_TEST06

13B-192V1 MR-376-X76-13B000$160.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
IMV = fuel flow actuator
TEST 6
CONTINUED
– Switch off the ignition, reconnect the electrical
connections to the four injectors and the low-pressure
actuator.
– Switch on the ignition again, and clear the injection
faults using the diagnostic tool.
– Check if there is no fuel leak in the high pressure
circuit. Run TEST 7 High pressure circuit sealing
check
– Check the conformity of the diesel filter. Run TEST 9
Diesel fuel filter check.
– Carry out fault finding on the injectors by checking the
return flow volume of the four injectors, run TEST 8
Injector return flow.
Is TEST 8 OK?The pump can supply the operating pressure.
Switch off the ignition, reconnect the electrical
connections
to the four injectors and the low pressure
actuator. Switch on the ignition again, and clear
the injection faults using the diagnostic tool.
– Check that there is no fuel leak in the high
pressure circuit, apply TEST 7 High pressure
circuit sealing check.
– Carry out fault finding on the injectors by
checking the return flow volume of the four
injectors, run TEST 8 Injector return flow.
If TEST 8 is correct, the high pressure fuel circuit
is correct.
Replace the faulty injector(s) (see MR
388 (Logan/Sandero), MR 451
(Duster), MR 423 (Thalia 2/Symbol 2)
or MR 374 (Kangoo VLL), Mechanical,
13B, Diesel injection, Diesel injector:
Removal - Refitting).Replace the high pressure pump (see MR 388 (Logan/Sandero),
MR 451 (Duster), MR 423 (Thalia 2/Symbol 2) or MR 374
(Kangoo VLL), Mechanical, 13B, Diesel injection, High
pressure pump: Removal - Refitting).
AB
YESNO

13B-197V1 MR-376-X76-13B000$160.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
TEST 8
CONTINUED 3
If the engine does not start, only the static leakage can be measured, i.e. the leakage with the injector closed, not
actuated and under high pressure.
Make sure that the ignition circuit is working correctly (minimum engine speed 200 rpm).
Tooling required
–Mot. 1711 Injector flow measuring kit.
Or: Use 4 pipes with internal diameter 4mm and approximately 50 cm in length, and a test adapter (TEST
IMV).
Procedure
– Switch off the ignition,
– disconnect the return pipes from the four injectors,
– cap the pump venturi tube to prevent the low-pressure circuit from depriming,
– connect the four transparent pipes in place of the return pipes (Mot. 1711),
– disconnect the low pressure actuator from the pump (brown IMV connector) and connect a test IMV or the Mot.
1711,
– electrically disconnect the four injectors,
– switch on the ignition and engage the starter for 5 seconds,
– measure the amount of diesel fuel in each pipe.
If the return leakage is greater than 10 cm, replace the injector(s) (see MR 388 (Logan/Sandero) or MR 451
(Duster), MR 423 (Thalia 2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 13B, Diesel injection, Diesel
injector: Removal - Refitting).
Switch off the ignition, and reconnect the four injectors electrically.
Disconnect the test low pressure actuator and reconnect the low pressure actuator connector to the pump.
Disconnect the four transparent tubes and reconnect the injectors return circuit. Switch on the ignition again, and
clear the injection faults using the diagnostic tool.
A

13B-200V1 MR-376-X76-13B000$160.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
TEST 11 Turbocharger air chain
Check for the air filter
Check the replacement interval of the air filter on the maintenance booklet.
Compare the part numbers of the air filter fitted to the vehicle and that of the air filter recommended by the
manufacturer.
Check the air filter direction of fitting.
Is the air filter fitted to the vehicle correct?
Check the condition of the air filter
Visually inspect the condition of the filtering section of the
air filter.
Is either the air filter or its seal damaged?
Is the air filter fouled (does it contain a lot of
impurities)?Replace the air filter (see MR 388
(Logan/Sandero), MR 423
(Thalia 2/Symbol 2), MR 451
(Duster) or MR 374 (Kangoo
VLL), Mechanical, 12A, Fuel
mixture, Air filter: Removal -
Refitting).
Low pressure circuit check
Note:
Depending on the vehicle type, the best visual access will
be either from above or from below.
Visually inspect the condition of the following
components:
– fresh air inlet scoop on the front panel of the vehicle,
– air inlet pipe to the air filter,
– air pipe of the filter until the compressor inlet,
– mountings of the air flowmeter.
Is one of these components incorrect (disconnected,
cut, bent, pierced or kinked pipes)?Replace the faulty parts (see MR
388 (Logan/Sandero), MR 451
(Duster), MR 423 (Thalia 2/
Symbol 2) or MR 374 (Kangoo
VLL), Mechanical, 12B,
Turbocharging).
YESNO
YES
NO
YES
A
NO
DCM1.2_V08_TEST11

13B-202V1 MR-376-X76-13B000$160.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
TEST 13 Diesel fuel conformity check
WARNING
During this operation, it is essential to:
– refrain from smoking or bringing incandescent objects close to the work area,
– guard against petrol splashes caused by the residual pressure in the pipes,
– wear safety goggles with side guards,
– wear leaktight gloves (Nitrile type).
IMPORTANT
– To avoid any corrosion or damage, protect the areas on which fuel is likely to run.
– To prevent impurities from entering the circuit, place protective plugs on all fuel circuit components
exposed to the open air.
Preparations:
Weigh an empty 1300 ml plastic cup (part no. 77 11 171 413) with its cover (part no. 77 11 171 416) using
electronic scales such as those used in body paint workshops (example: PANDA part no. 77 11 224 995). Record
the weight of the empty plastic cup.
This type of plastic cup is used to prepare paint.
Remove 1 l of fuel at the diesel filter outlet (see MR 388 (Logan/Sandero), MR 451 (Duster), MR 423 (Thalia
2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 19C, Tank, Draining the fuel tank), using a pneumatic
transfer pump (part no. 634-200) and place it in the 1300 ml plastic cup.
Cover the plastic cup with its cover and let it settle for approximately 2 minutes.
Is the fuel cloudy or does
it separate into two
parts?Presence of water in diesel fuel, the fuel is not compliant.
Drain the fuel system, including the tank (see MR 388 (Logan/
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2) or MR 374
(Kangoo VLL), Mechanical, 19C, Tank, Draining the fuel tank).
YES
A
NO
DCM1.2_V08_TEST13