fuel pressure RENAULT KANGOO 2013 X61 / 2.G Diesel DCM 1.2 Injection User Guide

13B-78
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF053
CONTINUED 2
1.DEF
2.DEF
3.DEF
5.DEF
7.DEF
NOTESNone.
Check the presence and conformity of fuel in the tank.
Apply test 13 Diesel fuel conformity check.
Run test 1 Low pressure circuit check.
Run test 6 High pressure system check.
Run test 8 Injector return flow

13B-79
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF056
PRESENT
OR
STOREDAIR FLOW SENSOR CIRCUIT1.DEF: Permanent low level
2.DEF: Permanent high level
3.DEF: At maximum limit
4.DEF: At minimum limit
NOTESPriorities when dealing with a number of faults:
– DF089 Inlet manifold pressure sensor circuit.
Special notes:
If fault DF056 is present: air flow regulation stops and the EGR valve is closed.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Check the condition of the air filter, replace the air filter if necessary (see MR388 (Logan/Sandero), MR423 (Thalia
2 / Symbol 2) or MR451 (Duster), Mechanical, 12A Fuel mixture, Air filter: Removal – Refitting).
Check that the inlet manifold is not obstructed (clogged).
Run TEST 5 Inlet circuit check.
Run TEST 11 Air line at the turbocharger
Check the connection and condition of the air flowmeter connector, component code 799.
Check the condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check for + 12 V after ignition feed on connection 3FB (or 3FBA) of the connector of the air flowmeter,
component code 799.
Check for + 5 V on connection 3KJ of the connector of the air flowmeter, component code 799.
Check the earth on connection NH on the connector of the air flowmeter, component code 799.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
DCM1.2_V08_DF056

13B-82
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF059
PRESENT
OR
STOREDCOMBUSTION MISFIRES ON CYLINDER 1
NOTESSpecial notes:
If the fault DF059 is present, the engine speed is maintained at 1000 rpm, engine
performance reduced to 75% and the level 2 warning light comes on.
Conditions for applying the fault finding procedure to a stored fault:
The fault is present with the engine idling.
Priority when dealing with a number of faults:
– DF026 Cylinder 1 injector circuit control (CC or CO).
– DF053 Rail pressure regulation function (1.DEF, 2.DEF, 7.DEF).
Check the presence and conformity of the fuel. Run test 13: Diesel fuel conformity check.
Run test 3 Injector check.
Check the engine compression.
Check the valve clearances and adjust them if necessary.
Check the inlet ducts, as well as the EGR valve, and clean them if necessary (see Technical Note 3916 Cleaning
the EGR solenoid valve).
If the fault is still present, replace the injector (see MR 388 (Logan/Sandero), MR 451 (Duster), MR 423 (Thalia
2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 13B, Diesel injection, Diesel injector: Removal –
Refitting).
If the fault is still present, contact the Techline.
DCM1.2_V08_DF059

13B-83
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF060
PRESENT
OR
STOREDMISFIRING ON CYLINDER 2
NOTESSpecial notes:
If the fault DF060 is present, the engine speed is maintained at 1000 rpm, engine
performance reduced to 75% and the level 2 warning light comes on.
Conditions for applying the fault finding procedure to a stored fault:
The fault is present with the engine idling.
Priority when dealing with a number of faults:
– DF027 Cylinder 1 injector circuit control (CC or CO).
– DF053 Rail pressure regulation function (1.DEF, 2.DEF, 7.DEF).
Check the presence and conformity of the fuel. Run test 13: Diesel fuel conformity check.
Run test 3 Injector check.
Check the engine compression.
Check the valve clearances and adjust them if necessary.
Check the inlet ducts, as well as the EGR valve, and clean them if necessary (see Technical Note 3916 Cleaning
the EGR solenoid valve).
If the fault is still present, replace the injector (see MR 388 (Logan/Sandero), MR 451 (Duster), MR 423 (Thalia
2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 13B, Diesel injection, Diesel injector: Removal –
Refitting).
If the fault is still present, contact the Techline.
DCM1.2_V08_DF060

13B-84
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF061
PRESENT
OR
STOREDMISFIRING ON CYLINDER 3
NOTESSpecial notes:
If the fault DF061 is present, the engine speed is maintained at 1000 rpm, engine
performance reduced to 75% and the level 2 warning light comes on.
Conditions for applying the fault finding procedure to a stored fault:
The fault is present with the engine idling.
Priority when dealing with a number of faults:
– DF028 Cylinder 1 injector circuit control (CC or CO).
– DF053 Rail pressure regulation function (1.DEF, 2.DEF, 7.DEF).
Check the presence and conformity of the fuel. Run test 13: Diesel fuel conformity check.
Run test 3 Injector check.
Check the engine compression.
Check the valve clearances and adjust them if necessary.
Check the inlet ducts, as well as the EGR valve, and clean them if necessary (see Technical Note 3916 Cleaning
the EGR solenoid valve).
If the fault is still present, replace the injector (see MR 388 (Logan/Sandero), MR 451 (Duster), MR 423 (Thalia
2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 13B, Diesel injection, Diesel injector: Removal –
Refitting).
If the fault is still present, contact the Techline.
DCM1.2_V08_DF061

13B-85
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF062
PRESENT
OR
STOREDMISFIRING ON CYLINDER 4
NOTESSpecial notes:
If the fault DF062 is present, the engine speed is maintained at 1000 rpm, engine
performance reduced to 75% and the level 2 warning light comes on.
Conditions for applying the fault finding procedure to a stored fault:
The fault is present with the engine idling.
Priority when dealing with a number of faults:
– DF029 Cylinder 1 injector circuit control (CC or CO).
– DF053 Rail pressure regulation function (1.DEF, 2.DEF, 7.DEF).
Check the presence and conformity of the fuel. Run test 13: Diesel fuel conformity check.
Run test 3 Injector check.
Check the engine compression.
Check the valve clearances and adjust them if necessary.
Check the inlet ducts, as well as the EGR valve, and clean them if necessary (see Technical Note 3916 Cleaning
the EGR solenoid valve).
If the fault is still present, replace the injector (see MR 388 (Logan/Sandero), MR 451 (Duster), MR 423 (Thalia
2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 13B, Diesel injection, Diesel injector: Removal –
Refitting).
If the fault is still present, contact the Techline.
DCM1.2_V08_DF062

13B-96
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF121
PRESENT
OR
STOREDACCELEROMETER CIRCUIT
1.DEF: No signal
NOTESPriorities when dealing with a number of faults:
– DF001 Coolant temperature sensor circuit,
– DF002 Air temperature sensor circuit,
– DF003 Atmospheric pressure sensor circuit,
– DF098 Fuel temperature sensor circuit,
A fault on one of these sensors could lead to incorrect fault finding on the
accelerometer.
Conditions for applying the fault finding procedure to a stored fault:
The fault is considered present when the engine is running.
Special notes:
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Check the conformity of the injectorsfitted to the vehicle in relation to the type of vehicle and engine number (low,
high or very high injector pressure).
Check the connection and condition of the accelerometer connector, component code 146.
Check the connection and condition of the injection computer connector, component code 120 and the shielding
of the sensor on connection TB1.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●3DQ between components 120 and 146,
●3S between components 120 and 146.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
DCM1.2_V08_DF121

13B-99
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF130
PRESENT
OR
STOREDFLOW CAPACITY FUNCTION
1.DEF: High flow capacity < minimum
2.DEF: High flow capacity > maximum
NOTESSpecial notes:
If the fault DF130 is present, the engine may stop and the level 2 warning light comes
on.
Conditions for applying the fault finding procedure to a stored fault:
The fault is considered present when the engine is running.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Check the connection and condition of the flow actuator (IMV) connector, component code 1105.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connection:
●3HI between components 120 and 1105.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
Measure the resistance between connections 3HI and 3FB (or 3FB2) of the flow actuator, component code 1105.
If the resistance of the flow actuator is not between: 4.8  < X < 5.8  at 20°C, replace the flow actuator (see MR
388 (Logan/Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical,
13B, Diesel injection, Flow actuator: Removal – Refitting).
Check the presence and conformity of fuel in the tank.
Apply test 13 Diesel fuel conformity check.
Run test 1 Low pressure circuit check.
If the fault is still present, run test 6 High pressure system check.
DCM1.2_V08_DF130

13B-123V1 MR-376-X76-13B000$080.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
PARAMETER CHECK (CONTINUED 1)
NOTESOnly perform this conformity check after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Air
temperaturePR058:Air
temperatureGives the inlet air temperature
in °C. This information is
supplied by the air
temperature sensor
incorporated in the air
flowmeter.
Default value: 20°C.In the event of a fault, consult the
interpretation of parameter
PR058 then consult the
interpretation of fault DF056 Air
flow sensor circuit.
Fuel
temperaturePR063:Fuel
temperatureCold = PR064
Warm: 50°C
Gives the fuel temperature in
°C. This value is measured by
the fuel temperature sensor.
Default value: 30°C.If there is a fault, use the
interpretation of fault DF098 Fuel
temperature sensor circuit.
Manifold air
temperaturePR311:Manifold air
temperatureIf the value supplied by this
parameter is equal to 50°C,
this does not correspond to a
fault and no interpretation
should be made for this
engine.
Atmospheric
pressurePR035:Atmospheric
pressureIndicates the atmospheric
pressure in mbar. The sensor
is built into the computer. In the event of inconsistency,
with the engine stopped and
ignition on, check that parameter
PR035PR312local
atmospheric pressure. Inlet manifold
vacuumPR312:Inlet manifold
vacuumIndicates the pressure in the
inlet circuit in mbar.

13B-124V1 MR-376-X76-13B000$080.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
PARAMETER CHECK (CONTINUED 2)
NOTESOnly perform this conformity check after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Battery voltagePR074:Battery
voltage12 V < PR074 < 14.4 V.In the event of a fault, run
fault finding on the
Charging circuit (see
Technical Note 6014A
(Renault) or Technical
Note 9859A (Dacia),
Checking the charging
circuit).
Air flowPR018:Estimated air
flowEstimation of the air flow by the
injection computer given in mg/st.NONE
Fuel flowPR017:Fuel flowPR017 = 0.0 mg/st
Gives the fuel flow at the high
pressure pump outlet in mg/st.NONE
Rail pressurePR038:Rail pressureEngine stopped: 1bar.
Indicates the pressure in bar of the
diesel fuel in the injector rail. This
pressure is supplied by the sensor
on the rail.
Default value: 2000 bar.If there is a fault, use the
interpretation of fault
DF007 Rail pressure
sensor circuit.
PR008:Rail reference
pressurePR008 = 375 bar (Engine starting
pressure setpoint)
Cold: 405 bar
Warm: 230 bar
Gives the theoretical pressure
value for optimum engine
operation.NONE