engine RENAULT KANGOO 2013 X61 / 2.G Petrol V42 Injection Repair Manual

17B-82V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
DF362
CONTINUED
K4M engine
Check the cleanliness and condition of the injection computer connector, component code 120, the pencil coil no.
2 connector, component code 1078 and the pencil coil no. 3 connector, component code 1079.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3CP between components 120 and 1078 (for Logan, Sandero, Duster),
–3CH between components 120 and 1078 (for Thalia 2/Symbol 2),
–3CF between components 120 and 1078 (for Kangoo VLL),
–3CW between components 1078 and 1079.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
With the ignition on, check the supply of the ignition coils, component code 1078 and 1079 using a test light on
connection 3NA of the injection relay, component code 1047 (for Logan, Sandero, Duster), on connection 3NA
of the fuel pump relay, component code 236 (for Kangoo VLL) or on connection 3N of the fuel pump relay,
component code 236 (for Thalia 2/Symbol 2).
Check the insulation, continuity and the absence of interference resistance on the following connection:
–3NA between components 1079 and 1047 (for Logan, Sandero, Duster) or 236 for Kangoo VLL),
–3N between components 1079 and 236 (for Thalia 2/Symbol 2).
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.

17B-83
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF363
PRESENT OR
STOREDCAMSHAFT DEPHASER1.DEF: Mechanical fault
2.DEF: Automatic control fault
3.DEF: Dephaser automatic control outside the limits
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present with the engine running at an engine speed of 2500 rpm
for 10 seconds.
–For 1.DEF, if impossible to see the fault present, deal with it as stored.
See the Wiring Diagrams Technical Note for Duster.
See Technical Note 6506A, Injection fault finding, Camshaft dephaser, ALP5 Operational fault (except
status CO, CC.1, CC.O) on the camshaft dephaser detected using Clip: DF080 "Camshaft dephaser circuit"
or DF063 "Camshaft dephaser" or DTC10 "Camshaft dephaser circuit" (K4M and F4R 830 Clio III RS).
If the fault is still present, contact the Techline.
V42_V04_DF363/V42_V05_DF363/V42_V06_DF363/V42_V14_DF363/V42_V16_DF363/V42_V18_DF363

17B-84
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 18
DF379
PRESENT OR
STOREDCYLINDER 1 INJECTOR CONTROLCO.1: Open circuit or short circuit to +12 V.
1.DEF: Inconsistent signal.
NOTESNone.
See Technical Note 6520 "Landi Renzo Euro V LPG system fault finding" (D4F734 engine on Logan and
Sandero) or Technical Note 6524 "Landi Renzo Euro V LPG system fault finding" (K4M616 engine on
Duster).
V42_V18_DF379

17B-85
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 18
DF380
PRESENT OR
STOREDCYLINDER 2 INJECTOR CONTROLCO.1: Open circuit or short circuit to +12 V.
1.DEF: Inconsistent signal.
NOTESNone.
See Technical Note 6520 "Landi Renzo Euro V LPG system fault finding" (D4F734 engine on Logan and
Sandero) or Technical Note 6524 "Landi Renzo Euro V LPG system fault finding" (K4M616 engine on
Duster).
V42_V18_DF380

17B-86
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 18
DF381
PRESENT OR
STOREDCYLINDER 3 INJECTOR CONTROLCO.1: Open circuit or short circuit to +12 V.
1.DEF: Inconsistent signal.
NOTESNone.
See Technical Note 6520 "Landi Renzo Euro V LPG system fault finding" (D4F734 engine on Logan and
Sandero) or Technical Note 6524 "Landi Renzo Euro V LPG system fault finding" (K4M616 engine on
Duster).
V42_V18_DF381

17B-87
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 18
DF382
PRESENT OR
STOREDCYLINDER 4 INJECTOR CONTROLCO.1: Open circuit or short circuit to +12 V.
1.DEF: Inconsistent signal.
NOTESNone.
See Technical Note 6520 "Landi Renzo Euro V LPG system fault finding" (D4F734 engine on Logan and
Sandero) or Technical Note 6524 "Landi Renzo Euro V LPG system fault finding" (K4M616 engine on
Duster).
V42_V18_DF382

17B-88V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
*TDC: Top Dead Centre
DF394
PRESENT OR
STOREDCATALYTIC CONVERTER OPERATING FAULT1.DEF: Component in bad condition
NOTESPriority when dealing with a number of faults:
Deal with the other faults first.
There must be no other injection system faults, either present or stored.
– DF081 - Canister bleed solenoid valve circuit
– DF120 - Engine speed sensor signal
– DF361 - Ignition coil 1-4 circuit
– DF362 - Ignition coil 2-3 circuit
– DF026 - Cylinder 1 injector control circuit
– DF027 - Cylinder 2 injector control circuit
– DF028 - Cylinder 3 injector control circuit
– DF029 - Cylinder 4 injector control circuit
– DF092 - Upstream oxygen sensor circuit
– DF082 - Upstream oxygen sensor heating circuit
– DF093 - Downstream oxygen sensor circuit
– DF002 - Air temperature sensor circuit
– DF001 - Coolant temperature sensor circuit
Conditions for applying the fault finding procedure to a stored fault:
The fault is not declared present, deal with the stored fault.
Special note:
OBD warning light comes on.
Check the downstream oxygen sensor (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/
Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 17B, Petrol injection, Oxygen sensors:
Removal - Refitting).
Check the programming of the TDC* sensor (see Section: Replacement of components).
Run the catalytic converter test SC006 Run OBD test: Catalytic converter and start the engine (only depress the
brake pedal to authorise the starting of the engine,
do not touch the accelerator pedal or clutch pedal).
At the end, check the test results:
STATUS1: Fault finding was not performed/impossible to obtain the necessary conditions
STATUS2: The component is in an average condition - sensor OK
STATUS3: The component is in a good condition - sensor OK
STATUS4: The component is in poor condition - replace the catalytic converter (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 19B, Exhaust, Catalytic converter: Removal - Refitting).
If the fault is still present, contact the Techline.
V42_V04_DF394/V42_V05_DF394/V42_V06_DF394/V42_V14_DF384/V42_V16_DF384/V42_V18_DF384

17B-89V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
DF398
PRESENT OR
STOREDFUEL CIRCUIT OPERATING FAULT
1.DEF: Component in poor condition.
NOTESPriority when dealing with a number of faults:
Deal with the other faults first.
– DF085 - Fuel pump relay control circuit
Conditions for applying the fault finding procedure to a stored fault:
The fault is declared present with the engine running at an engine speed of 2500 rpm
for 10 seconds.
Special note:
OBD warning light comes on.
Check the value of parameter PR139 Operating richness adaptive.
If the value of PR139 < 1 then:
Check the sealing of the fuel supply system from the fuel pump to the injector rail:
– The fuel tank (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio
II F 6) or MR 374 (Kangoo VLL), Mechanical, 19C, Tank, Fuel tank: Removal - Refitting),
– The connection between the fuel pump and the fuel filter (see MR 388 (Logan and Sandero) Mechanical, 19C,
Tank, Fuel supply pipe: Removal - Refitting, MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio
II F 6), MR 374 (Kangoo VLL), Mechanical, 19C, Tank, Fuel tank: Removal - Refitting),
– The connection between the fuel filter and the regulator (see MR 388 (Logan and Sandero), MR 451 (Duster)
or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6), MR 374 (Kangoo VLL), Mechanical, 13A, Fuel supply,
Fuel filter: Removal - Refitting),
– The pressure regulator ducts (see MR 388 (Logan and Sandero), Mechanical, 19C, Tank, Fuel supply pipe:
Removal - Refitting, MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6), MR 374 (Kangoo
VLL), Mechanical, 19C, Tank, Fuel tank: Removal - Refitting),
– The connection between the regulator and the injector rail (see MR 388 (Logan and Sandero), Mechanical, 19C,
Tank, Fuel supply pipe: Removal - Refitting, MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio
II F 6), MR 374 (Kangoo VLL), Mechanical, 19C, Tank, Fuel tank: Removal - Refitting),
V42_V04_DF398/V42_V05_DF398/V42_V06_DF398/V42_V14_DF398/V42_V16_DF398/V42_V18_DF398

17B-93
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
V2 MR-376-X76-17B050$083.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 18
DF436
PRESENT OR
STOREDDETECTION OF ENGINE MISFIRING1.DEF: Polluting misfiring.
2.DEF: Destructive misfiring.
NOTESPriority when dealing with a number of faults:
– DF109 Low fuel level misfire,
– DF635 LPG cylinder 1 combustion misfire,
– DF636 LPG cylinder 2 combustion misfire,
– DF637 LPG cylinder 3 combustion misfire
– DF638 LPG cylinder 4 combustion misfire.
Conditions for applying the fault finding procedure to stored faults:
The fault is considered present under the following conditions:
– engine running at idling speed.
Special note:
OBD warning light comes on.
1.DEF
NOTESNone.
Check the ignition coil circuits (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol
2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 13A, Fuel supply, Fuel circuit: Operating
diagram),
Check the fuel supply pump circuit (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/
Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the condition of the cylinder injectors (see MR 388 (Logan and Sandero), Mechanical, 13A, Fuel supply,
Injector rail - Injectors: Removal - Refitting, MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II
F 6), MR 374 (Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting),
Check the cylinder compressions.
V42_V18_DF436

17B-94
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$083.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 18
DF436
CONTINUED 1
After repair, check that the catalytic converter is not damaged by the misfire.
To do this, switch on the ignition, run the catalytic converter test SC006 Run OBD test: Catalytic converter and
start the engine (only depress the brake pedal to authorise the starting of the engine,
do not touch the accelerator pedal or clutch pedal).
At the end, check the test results:
STATUS1: Fault finding was not performed/impossible to obtain the necessary conditions
STATUS2: The component is in an average condition - sensor OK
STATUS3: The component is in good condition - sensor OK
STATUS4: The component is in poor condition - replace the catalytic converter (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 19B, Exhaust, Catalytic converter: Removal - Refitting).