door lock RENAULT SCENIC 2007 J84 / 2.G Electrical Equipment - Xenon Bulbs Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2007, Model line: SCENIC, Model: RENAULT SCENIC 2007 J84 / 2.GPages: 38, PDF Size: 0.12 MB
Page 7 of 38
80C -7V2 MR-372-J84-80C000$020.mif
XENON BULBS
Fault finding – System operation80C
Program No.: V010
Vdiag No.: 05
3. CONFIGURATION-CALIBRATION OF THE SYSTEM
To calibrate and configure a new computer on a vehicle, follow the configuration procedures in the following order.
a. Vehicle type (CF003)
This configuration activates the adjustment strategies designed for the body type.
The new strategies only take effect after the ignition is switched off and the doors are locked.
Perform configuration as follows:
–Enter the xenon bulbs fault finding mode.
–Make sure that the initial vehicle position indicated by the front and rear sensors is within the allowed range.
–Run configuration CF003 according to the vehicle type:
– Scénic II Strd* (5-seater MPV)
– Scenic II Long (7-seater extended MPV)
– Espace IV
– Velsatis
– Laguna II
–Exit fault finding mode.
–Switch off the ignition.
–Lock the doors using the card.
–The vehicle type has been programmed.
–After unlocking the doors, turn the ignition back on.
–See that the vehicle type has been properly identified by reading configuration LC001, Vehicle type.
b. Computer calibration (CF001)
This calibration must be performed when a system component is replaced (e.g. sensor, headlight etc.).
It enables the computer to store the vehicle's reference level.
To ensure proper configuration and calibration, follow this procedure:
–Check tyre pressure and adjust if faulty.
–Park the vehicle on a level surface under normal driving conditions (luggage compartment empty).
–Vehicle stopped, solid base (no door rattling).
–Driver on board.
–Fuel tank full.
Once computer calibration has been performed, check conformity of the light beam.
If it is incorrect, adjust the headlights manually.
Page 10 of 38
80C-10V2 MR-372-J84-80C000$040.mif
80C
Program No.: V010
Vdiag No.: 05
AFTER REPAIRTurn on dipped-beam headlights.
Check that the system performs its initialisation to verify that the computer has no
faults.
Adjust the headlights manually.
CF001COMPUTER CALIBRATION
NOTESThis configuration enables the computer to store the vehicle's reference level.
Begin by configuring the vehicle type; then calibrate the vehicle level.
The vehicle must be stationary. Also, the front and rear sensor values must be within
the permissible range.
To calibrate the computer, proceed as follows:
–Check tyre pressure and adjust if faulty.
–Park the vehicle on a level horizontal surface.
–Make sure that the headlights have been properly adjusted manually.
–Position the vehicle with the wheels set straight ahead, engine switched off, driver behind the wheel and dipped
headlights on.
–Turn on the ignition and enter xenon bulbs fault finding mode.
–Select Configuration mode.
–Run configuration CF001.
–When calibration is complete, exit fault finding mode.
–Lock and unlock the vehicle doors with the card.
–The computer has now been calibrated.
–Check status LC010, which should indicate Completed.
LC010COMPUTER CALIBRATIONNot completed
Completed
The configuration reading LC010 can have either of two statuses:
–Not completed: The computer has not been calibrated, the vehicle's reference level is unknown, and the
maximum and minimum body height levels have not been programmed.
–Completed: The computer has been calibrated. Normal system operation. The sensor reference levels have
been programmed.
XENON BULBS
Fault finding – Configurations and programming
Page 11 of 38
80C-11
AFTER REPAIRTurn on dipped-beam headlights.
Check that the system performs its initialisation to verify that the computer has no
faults.
Adjust the headlights manually.
V2 MR-372-J84-80C000$040.mif
XENON BULBS
Fault finding – Configurations and programming80C
Program No.: V010
Vdiag No.: 05
* Strd: standard
CF003VEHICLE TYPE
NOTESThis configuration is performed after replacing the computer.
Configuration procedure:
–Connect the CLIP tool and turn on the ignition.
–Enter Xenon bulbs fault finding mode.
–Select configuration CF003 Vehicle type.
–Select the type of vehicle.
–Confirm the configuration.
–Exit fault finding mode and switch off the ignition.
–Lock and unlock the vehicle doors with the card.
–Re-enter "Discharge bulbs" fault finding mode and read LC001 "Vehicle type".
–See that the vehicle type has been properly identified by reading configuration LC001.
LC001VEHICLE TYPE
Not defined
Scénic II Strd*
Scénic II long
Velsatis
Laguna II
Espace IV
Configuration LC001 can have one of six statuses:
–Not defined: Configuration CF003 Vehicle type, has been completed, but the vehicle type programmed does
not match the vehicle diagnosed.
–Scénic II Strd*: Configuration correct: the vehicle type is Scénic.
–Scénic II long: Configuration correct: the vehicle type is the extended Scénic.
–Velsatis: Configuration correct: the vehicle type is Velsatis.
–Laguna II: Configuration correct: the vehicle type is Laguna II.
–Espace IV: Configuration correct: the vehicle type is Espace IV.