warning RENAULT SCENIC 2007 J84 / 2.G Power Assisted Steering Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2007, Model line: SCENIC, Model: RENAULT SCENIC 2007 J84 / 2.GPages: 59, PDF Size: 0.19 MB
Page 10 of 59
POWER-ASSISTED STEERING
Fault finding – Replacement of components
36B
36B-10V5 MR-372-J84-36B000$264_fra.mif
EPAS
Vdiag no.: 05, 09,
0DPOWER-ASSISTED STEERING
Fault finding – Replacement of components
Precautions for use
–The computer, electric motor, upper steering column and angle sensor unit (EPAS) cannot be separated.
A. Replacing the EPAS (computer - upper column assembly):
Before replacing the EPAS, run fault finding on the system: apply the appropriate fault finding procedure.
The EPAS may be replaced only with the consent of the Techline.
When replacing the electric power assisted steering, carry out the following operations in order:
–disconnect the vehicle battery,
–replace the EPAS (see Workshop Repair Manual 370 Mechanics, 36B, Electric power assisted steering),
–reconnect the vehicle battery,
–connect the diagnostic tool, switch on the ignition and establish dialogue with the PAS computer, write the vehicle
VIN by running command VP001,
–configure (see Configuration and programming),
–program the steering wheel angle sensor (only for Vdiag 05 and 09) (see Configuration and programming),
–write the most recent After-Sales operation date by running command VP005,
–switch off the ignition for at least 15 seconds for the configurations to register, without disconnecting the battery,
–switch on the ignition and establish dialogue with the electric power-assisted steering computer,
–turn the steering wheel to full right lock and then to full left lock,
–check that there are no faults and that the variables are correct (notably parameter PR121 Steering wheel angle
for the Vdiag 05 and 09),
–check that the EPAS is working correctly (steering assistance available when the engine is running).
B. Replacing the steering rack (without changing the EPAS):
–disconnect the vehicle battery,
–replace the steering rack (see MR 370 Mechanics, 36B, EPAS),
–reconnect the vehicle battery,
–connect the diagnostic tool, switch on the ignition and establish dialogue with the electric power-assisted steering
computer (EPAS computer),
–program the steering wheel angle sensor (only for Vdiag 05 and 09) (see Configuration and programming),
–turn the steering wheel to full right lock and then to full left lock,
–makesure there a re n o faults a nd check the conformity o f paramete rPR121 Steering wheel angle (Vdiag 05 and 0 9),
–check that the EPAS is working correctly (steering assistance available when the engine is running).
* APV: After-SalesWARNING
You must never leave the ignition switched on or the engine running during a mechanical operation on the electric
power assisted steering or the front axle. To avoid any accident, the battery must be disconnected (to prevent
the danger of accidental triggering of the EPAS motor).
MR-372-J84-36B000$264_fra.mif
Page 13 of 59
POWER-ASSISTED STEERING
36B
36B-13V5 MR-372-J84-36B000$396_fra.mif
EPAS
Vdiag no.: 05, 09,
0DPOWER-ASSISTED STEERING
Fault finding – Fault summary table
Tool
faultDiagnostic tool titleAssociated
DTCCustomer complaints and warning light
coming on
DF001Motor thermal protection5614Steering assistance intermittent reduction.
DF002Computer5608Assistance limited to 30% (with SERVICE
warning light + message) or no assistance
(with STOP warning light + message)
depending on the internal fault code.
DF020Computer supply5601Degraded assistance (no warning light or
message) until a loss of assistance below
9 V or above 17 V with STOP indicator light
+ Message.
DF021Steering wheel angle sensor
programming (only for Vdiag 05 and 09)5612Degraded steering wheel recall (with
SERVICE indicator light + message). ESP
fault, if present.
DF023+ after ignition feed5613Assistance gradually cuts out (within
5 minutes). When the ignition is next
switched on there is no steering
assistance.
DF033Multiplex networkD000Inappropriate level of assistance:
SERVICE indicator light + Message.
DF035Variable power assisted steering motor5606Assistance limited to 30% (with SERVICE
warning light + message) or no steering
assistance (with STOP warning light
+ Message).
DF038Angle sensor (only Vdiag 05 and 09) 5605Steering wheel recall degraded
(no warning light or message). ESP fault,
if present.
DF053Computer configuration5602Defect mode assistance (no message
or warning light).
DF054Torque sensor5604Steering assistance loss or absence with
STOP indicator light + Message.
DF055Computer memory5607Degraded assistance (without warning
light or message) or assistance limited to
10% with SERVICE warning light
+ Message.
Risk of ESP fault.
DF057Vehicle speed multiplex signalD200Inappropriate level of assistance:
SERVICE indicator light + Message.
Note:
Warning light/message
SERVICE + "Check steering" or,
STOP + audible warning + "Faulty steering" or "EPAS fault", depending on the type of instrument panel.
MR-372-J84-36B000$396_fra.mif
Page 16 of 59
POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-16V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
DF020
PRESENT
OR
STOREDCOMPUTER SUPPLY VOLTAGE
1.DEF: Voltage too low
2.DEF: Voltage too high
CO: Open circuit
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is considered present when the engine is running.
Notes:
This fault causes a degraded assistance (no warning light or message) until assistance
is lost (below 9 V or above 17 V) with STOP warning light + Message.
–The computer records an occurrence context (computer operating values frozen
when fault occurs). To view this information, click on the fault description (camera
symbol). Within these values, parameter PR143 Internal fault code gives the fault
finding procedure to apply.
Procedure to apply for internal fault code 135 of the PR143
Check the conditioning and positioning of the EPAS supply fuses:
–Power fuse (80A BP81) in the engine fuse box.
–AP44 after ignition fuse (5A) in the Protection and Switching Unit.
Check the condition and tightness of the battery and alternator terminals, as well as the Protection and Switching
Unit bolt.
Carry out fault finding on the charge circuit.
Repair if necessary.
Disconnect the two black connectors from the EPAS computer.
Check the condition and conformity of the connectors and their clips.
Check the conformity of the electrical supplies (they must be equal to the battery voltage).
In the event of a fault, check the insulation, continuity and the absence of interference resistance on the
following connections:
8-track connector track 8 + 12 V after ignition
2-track connector track 1 + 12 V before ignition feed
2-track connector track 2 Earth
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF020/DAE_V09_DF020/DAE_V0D_DF020
Page 18 of 59
POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-18V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09
DF021
PRESENT
PROGRAMMING THE STEERING WHEEL ANGLE SENSOR
DEF: Programming not carried out or incorrect
NOTESNotes:
This fault is present for as long as the steering wheel angle is not calibrated.
It is automatically cleared as soon as the programming procedure is completed.
This fault causes an absence of steering wheel recall (with warning light
continuously on).
Place the vehicle on a front axle adjusting bench.
Position the vehicle wheels in the straight line driving position (steering centre point).
Program the steering wheel angle via command VP004 Steering wheel angle sensor programming
(see Configuration and programming, section A).
Vehicle in straight line driving position (steering centre point).
Refer to parameters PR121 Steering wheel angle and PR007 Steering wheel angle offset compensation.
Both parameters must be 0˚.
Turn the steering wheel to full right lock then to full left lock, and check that the parameter varies within the
tolerances given in the conformity check.
Refer to status ET020 Steering wheel angle sensor programming, which must be STATUS 4.
Start the engine and check the operation of the EPAS by turning the steering wheel from lock to lock
(parking manoeuvres).
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF021P/DAE_V09_DF021P
Page 21 of 59
POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-21V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
DF035
PRESENT
OR
STOREDVARIABLE POWER ASSISTED STEERING MOTOR
DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after having started the engine and turned the steering
wheel from lock to lock.
Notes:
This fault causes a loss of assistance or an absence of steering assistance and also
illuminates the STOP warning light + Message, or assistance is limited to 30% and
the SERVICE indicator light + Message come on.
–The computer records an occurrence context (computer operating values frozen
when fault occurs). To view this information, click on the fault description (camera
symbol). Within these values, parameter PR143 Internal fault code gives the fault
finding procedure to apply.
Procedure to apply for internal fault codes 3, 33, 34, 35, 50, 51, 112, 113, 128, 145 of PR143.
Contact Techline.
Procedure to apply for internal fault codes 4, 5, 100, 114, 115, 129, 130 and 131 of PR143.
Check the condition of the wiring inside the EPAS and make sure that the 3 white EPAS connectors are correctly
locked.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF035/DAE_V09_DF035/DAE_V0D_DF035
Page 22 of 59
POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-22V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09
DF038
PRESENT
OR
STOREDANGLE SENSOR
1.DEF: Sensor internal electrical fault
2.DEF: Absence of sensor signal
3.DEF: Values outside limits
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after having started the engine and turned the steering
wheel from lock to lock.
Notes:
This fault causes an absence of steering wheel return (no warning light or message).
–The computer records an occurrence context (computer operating values frozen
when fault occurs). To view this information, click on the fault description (camera
symbol). Within these values, parameter PR143 Internal fault code gives the fault
finding procedure to apply.
Procedure to apply for internal fault codes 195 and 196 of PR143.
Position the vehicle wheels in the straight line driving position (steering centre point).
Refer to parameters PR121 Steering wheel angle and PR007 Steering wheel angle offset compensation.
Both parameters must be between - 10˚ < X < 10˚.
Turn the steering wheel to full right lock then to full left lock, and check that the parameter varies within the
tolerances given in the "Conformity check".
Refer to status ET020 Steering wheel angle sensor programming, which must be STATUS 4.
If parameters PR121, PR007 and status ET020 are not correct:
Place the vehicle on a front axle adjusting bench.
Position the vehicle wheels in the straight line driving position (steering centre point).
Program the steering wheel angle via command VP004 Steering wheel angle sensor programming (see
Configuration and programming, section A).
Remove the fault, start the engine and check that the EPAS functions correctly by turning the steering wheel from
lock to lock (parking manoeuvres).
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF038/DAE_V09_DF038
Page 24 of 59
POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-24V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
DF053
PRESENT
COMPUTER CONFIGURATION
DEF: Computer calibration not carried out
NOTESPriority in the event of a number of faults:
Deal with fault DF020 Computer supply voltage first, if it is present or stored.
Notes:
This fault is present for as long as the computer assistance strategy is not configured.
It is automatically cleared after configuration.
This fault causes:
Degraded assistance (no message or warning light).
Check that the computer's configuration correctly corresponds to the vehicle type, engine type, gearbox and tyres
fitted on the vehicle.
Reconfigure the computer if necessary (see Configuration and programming).
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF053P/DAE_V09_DF053P/DAE_V0D_DF053P
Page 25 of 59
POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-25V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
DF054
PRESENT
OR
STOREDTORQUE SENSOR
DEF: Sensor internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after having started the engine and turned the steering
wheel from lock to lock, then returning it to the centre.
Notes:
This fault causes:
Loss or absence of steering assistance with STOP warning light + Message
lighting up.
–The computer records an occurrence context (computer operating values frozen
when fault occurs). To view this information, click on the fault description (camera
symbol).
Within these values, parameter PR143 Internal fault code gives the fault finding
procedure to apply.
If, in the fault occurrence context (computer operating values frozen when fault
occurs) PR108 Computer supply voltage is less than 10 V, check the battery
voltage, the tightness and the condition of the battery terminals and check the
charging circuit.
Procedure to apply for internal fault codes 1 and 69 of PR143.
Contact Techline.
Procedure to apply for internal fault codes 48, 66, 64, 65 and 67 of PR143.
Check the condition of the 3 white EPAS connectors and check that they are locked correctly.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF054/DAE_V09_DF054/DAE_V0D_DF054
Page 26 of 59
POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-26V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
DF055
PRESENT
OR
STOREDCOMPUTER MEMORY
DEF: EEPROM irregularity
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after having started the engine and turned the steering
wheel from lock to lock, then returning it to the centre.
Notes:
This fault leads to degraded assistance with no warning light or message or an
assistance that is limited to 10% with the SERVICE indicator light + Message.
–Risk of ESP fault.
–The computer records an occurrence context (computer operating values frozen
when fault occurs). To view this information, click on the fault description (camera
symbol). Within these values, parameter PR143 Internal fault code gives the fault
finding procedure to apply.
Procedure to apply for internal fault codes 83 and 85 of PR143.
Only for Vdiag 05 and 09:
Check status ET020 Steering wheel angle programming which should be STATUS 4; if not, program the
steering wheel angle sensor VP004 Steering wheel angle programming (see Configuration and
programming).
If the fault is still present after the ignition has been switched on several times, contact the Techline.
Procedure to apply for internal fault codes 84 and 86 of PR143.
Contact Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF055/DAE_V09_DF055/DAE_V0D_DF055
Page 47 of 59
POWER-ASSISTED STEERING
Fault finding – Customer complaints
36B
36B-47V5 MR-372-J84-36B000$858_fra.mif
EPAS
Vdiag no.: 05, 09,
0DPOWER-ASSISTED STEERING
Fault finding – Customer complaints
NOTESOnly refer to the customer complaints after performing a complete check using the
diagnostic tool.
NO DIALOGUE WITH THE COMPUTER ALP1
LOSS OF VEHICLE ASSISTANCE WITHOUT WARNING ALP2
POOR VEHICLE HANDLINGALP3
THE STEERING WHEEL DOES NOT RETURN BY ITSELF
TO THE CENTRE AT LOW SPEED: STEERING WHEEL
RETURN TO CENTRE POINT INACTIVE (ONLY FOR
VDIAG 05 AND 09)ALP4
UNDER-ASSISTANCE AT LOW SPEED AND OVER-
ASSISTANCE AT HIGH SPEED WITHOUT WARNINGALP5
TOO LITTLE ASSISTANCEALP6
ASSISTANCE AVAILABLE FOR 5 MIN. AFTER
SWITCHING OFF THE IGNITIONALP7
ASSISTANCE AVAILABLE BUT CHECK STEERING
WARNING MESSAGE DISPLAYED AND SERVICE
INDICATOR LIGHT CONTINUOUSLY LITALP8
THE VEHICLE PULLS TO THE RIGHT OR TO THE LEFT ALP9
SERVICE INDICATOR LIGHT AND CHECK STEERING
MESSAGE COME ON STRAIGHT AWAYALP10
STEERING ASSISTANCE IS AVAILABLE WITH IGNITION
ON AND ENGINE STOPPED, WITH NO WARNINGALP11
THE ENGINE DOES NOT START AND THE MESSAGE
"STEERING NOT UNLOCKED" IS DISPLAYED
OR
THE MESSAGE "STEERING NOT UNLOCKED" IS
DISPLAYED AFTER THE IGNITION IS SWITCHED OFFALP12
MR-372-J84-36B000$858_fra.mif