tyre pressure RENAULT SCENIC 2008 J84 / 2.G Electrical Equipment - Instrument Panel Workshop Manual

83A-10
MR-372-J84-83A000$252.mif
V8
INSTRUMENT PANEL
Fault finding - Configurations and programming83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
*Miles Per HourLC no. CF no. Configuration Note:
LC049 Type of fuelPetrol: check that the rev counter indicates
7000 rpm as the maximum value.
Diesel: check that the rev counter indicates
6000 rpm as the maximum value and that the
diesel heater plugs “on” indicator light comes
on when the ignition is switched on.
IMPORTANT
it is essential to check this, as it
determines whether the gauges are
operating correctly.
LC051 CF140 Unit of distance
LC052 CF141 Overspeed function - ArabiaWhen driving at speeds greater than
78 mph (130 km/h), the buzzer should sound.
LC054 CF143Unit of measurement for
consumptionLitres/ 100 km (default) - Europe
Miles / gallon - UK
km / l - Brazil
LC056 CF145 Tyre pressure monitorCheck for specific valves.
If the vehicle is equipped with a tyre pressure
monitor: check that the vehicle outline does
not show wheels which are absent and that
there is no “No tyre sensors” message
(message indicating the tyre pressure
monitoring frames are absent).
LC059 CF148 Automatic headlightingCheck for a brightness sensor.
Disconnect the automatic headlights, and
check that the "Auto Headlights Off" message
is displayed.

83A-23
MR-372-J84-83A000$441.mif
V8
INSTRUMENT PANEL
Fault finding - Conformity check83A
TDB ph2 (EG/MG)
Prog version: 04xx
Vdiag No.: 08, 0C
DISPLAY
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Ignition on, engine off.
Order FunctionParameter, Status
Check or ActionDisplay and notes Fault finding
1Vehicle
speedPR099:Vehicle speedX mph (km/h)In the event of a fault, consult
the interpretation of parameter
PR099 Vehicle speed.
2
EnginePR116:Engine speedX rpmIn the event of a fault, consult
the interpretation of parameter
PR116 Engine speed.
3PR027:Coolant
temperature"X" ˚CIn the event of a fault, consult
the interpretation of parameter
PR027 Coolant temperature.
4
LightingPR111:Lighting dimmer
voltageIgnition on, dipped
headlights lit.
0.3 V < PR111 < 7 VIn the event of a fault, contact
the Techline.
5AC009:Instrument panel
warning lightsThe command lights
up all the indicator
lights at the same
time.In the event of a fault, consult
the interpretation of commands
AC009 Instrument panel
warning lights.
6AC010:LightingThe lighting intensity
will vary to 50% then
100% of its maximum
intensity for
5 seconds each time.In the event of a fault, consult
the interpretation of commands
AC010 Lighting.
7 Needle
gaugesAC008:Instrument panel
needle gaugesInstrument panel
needle gauge control.In the event of a fault, consult
the interpretation of command
AC008 Instrument panel
needles.
8Display AC007:DisplayThe display shows the
mileage as well as the
range.
All areas of the display
must light up at the
same time.In the event of a fault, consult
the interpretation of command
AC007 Display.
9Symbol
displayAC011:Symbol displayThe symbol display
shows the status of
the opening elements
and the tyre pressure.In the event of a fault, consult
the interpretation of command
AC011 Symbol display.

83A-46
MR-372-J84-83A000$819.mif
V8
INSTRUMENT PANEL
Fault finding - Interpretation of commands83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
AC011
DOT MATRIX DISPLAY
NOTESIMPORTANT
–Affects the opening elements indicator lights (on mid-range instrument panels).
–Affects tyre pressure monitor system warning lights (on mid-range instrument panel
if fitted to the vehicle).
–Affects automatic and sequential gearbox warning lights.
There must be no present or stored faults.
Activate the dot matrix display using command AC011 Dot matrix display.
The dot matrix display lights up.
If there is a lighting fault, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.