lights RENAULT SCENIC 2008 J84 / 2.G Electrical Equipment - Instrument Panel Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2008, Model line: SCENIC, Model: RENAULT SCENIC 2008 J84 / 2.GPages: 63, PDF Size: 0.19 MB
Page 2 of 63
83A-2
MR-372-J84-83A000$063.mif
V8
83A
INSTRUMENT PANEL
Fault finding - Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding method applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this document):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM), paper.
Type of diagnostic tools
–CLIP
Special tooling required
3. REMINDERS
To run fault finding on the vehicle's computers, switch on the ignition in fault finding mode (forced + after ignition
feed).
Proceed as follows:
–vehicle card in reader,
–press and hold the Start button (longer than 5 seconds) with start-up conditions not fulfilled,
–connect the diagnostic tool and perform the required operations.
To cut off the + after ignition feed, proceed as follows:
–disconnect the diagnostic tool,
–press the Start button twice briefly (less than 3 seconds),
ensure that the + after ignition feed has been cut off by checking that the computer indicator lights on the instrument
panel have gone out.Vehicle(s): Scénic II
Function concerned: Instrument panelName of computer: Instrument Panel
2 levels:
Entry level version, Scénic II phase 2
Mid level version, Scénic II phase 2
Program Version: 04xx
Vdiag No.: 08, 0C
Special tooling required
Multimeter
Elé. 1681Universal bornier
TDB_V08_PRELI/TDB_V0C_PRELITDB ph2 (EG/MG)
Prog version: 04xx
Vdiag No.: 08, 0C
MR-372-J84-83A000$063.mif
Page 7 of 63
83A-7
MR-372-J84-83A000$126.mif
V8
83A
INSTRUMENT PANEL
Fault finding - System operation
Instrument panel functions (entry level and mid-range versions):
The instrument panel allows:
–display by needle gauge of the following information:
–Vehicle speed
–Rev counter
–Fuel gauge
–Engine coolant temperature
–Management of 20 warning/indicator lights
–Alphanumeric display of the following information:
–Total and trip mileage
–Oil level
–Messages (68 messages)
–Keyless vehicle messages
–Warning messages
–Management of a multifunction buzzer:
The buzzer is used for the following functions:
–Indicating the operation of the direction indicators.
–Signalling that the lights have been left on.
–Indicating that the driver's or passenger's seat belts are not fastened when driving.
–Indicating that a door or the tailgate is not correctly closed.
–Signalling that the handbrake is on.
–Indicating the low fuel warning.
–Indicating that a speed has been exceeded, for Arabian versions, where an overspeed warning
is legally required.
–Indicating to the driver that the automatic locking when driving has been activated/deactivated.
The following buzzers can sound:
–Side lights on
–Direction indicators
–Management and trip computer display:
–Trip meter
–Fuel consumed
–Average fuel consumption
–Instantaneous fuel consumption
–Fuel range in kilometres and miles
–Distance travelled in kilometres and miles
–Average speed
–Oil service interval in kilometres
–Oil service interval in time
–Programmed speed (if the cruise control and speed limiter feature is present).
–Instrument panel dimmer: when the lights are on, the brightness of the instrument panel can be adjusted
using a button located on the instrument panel.
–In the event that the childproof lock system is not working, the buzzer will sound and a warning message
will appear on the instrument panel.
In vdiag 08 (with program version 040B) and vdiag 0C, the instrument panel can manage a personalised oil service
interval (known as the OCS) by detecting premature oil wear (depending on the engine). If the engine has this oil
wear detection management function, the oil service interval will initially be increased. The oil service interval could
however decrease more quickly if a “severe” type of driving (urban driving, diving in traffic jams, etc.) is detected by
the injection computer. The instrument panel will display a message to request that an oil service be performed
quickly, without necessarily displaying a warning message beforehand.
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
MR-372-J84-83A000$126.mif
Page 10 of 63
83A-10
MR-372-J84-83A000$252.mif
V8
INSTRUMENT PANEL
Fault finding - Configurations and programming83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
*Miles Per HourLC no. CF no. Configuration Note:
LC049 Type of fuelPetrol: check that the rev counter indicates
7000 rpm as the maximum value.
Diesel: check that the rev counter indicates
6000 rpm as the maximum value and that the
diesel heater plugs “on” indicator light comes
on when the ignition is switched on.
IMPORTANT
it is essential to check this, as it
determines whether the gauges are
operating correctly.
LC051 CF140 Unit of distance
LC052 CF141 Overspeed function - ArabiaWhen driving at speeds greater than
78 mph (130 km/h), the buzzer should sound.
LC054 CF143Unit of measurement for
consumptionLitres/ 100 km (default) - Europe
Miles / gallon - UK
km / l - Brazil
LC056 CF145 Tyre pressure monitorCheck for specific valves.
If the vehicle is equipped with a tyre pressure
monitor: check that the vehicle outline does
not show wheels which are absent and that
there is no “No tyre sensors” message
(message indicating the tyre pressure
monitoring frames are absent).
LC059 CF148 Automatic headlightingCheck for a brightness sensor.
Disconnect the automatic headlights, and
check that the "Auto Headlights Off" message
is displayed.
Page 21 of 63
83A-21
MR-372-J84-83A000$441.mif
V8
83A
INSTRUMENT PANEL
Fault finding - Conformity check
MAIN COMPUTER STATUSES AND PARAMETERS
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Ignition on, engine off.
Order FunctionParameter, Status
Check or ActionDisplay and notes Fault finding
1
SupplyPR110:Battery voltage11.5 V < PR110 < 16 VIn the event of a fault, consult
the interpretation of fault
DF019 Battery voltage.
2ET002:+ 12 V after
ignitionAbsent
PresentIn the event of a fault, refer to
the interpretation of status
ET002 + 12 V after ignition.
3
BrakeET097:Parking brakeApplied
ReleasedIn the event of a fault, consult
the interpretation of status
ET097 Parking brake.
4ET066:Brake fluid level
light alertIndicates the brake
fluid level.
PRESENT: Level too
low
ABSENT: Level correctIn the event of a fault, consult
the interpretation of status
ET066 Brake fluid level light
warning.
5Lighting PR111:Lighting dimmer
voltageIgnition on, dipped
headlights lit.
0.3 V < PR111 < 7 VIf the fault is still present,
contact Techline.
6Oil ET096:Oil pressure
contactOpen: indicator light off
Closed: indicator light
onIn the event of a fault, consult
the interpretation of status
ET096 Oil pressure contact.
7
Seat beltET098:Driver's seat belt
contactPresent (fastened)
AbsentIn the event of a fault, consult
the interpretation of status
ET098 Driver's seat belt
contact.
8ET062:Seat belt alarmOff
onIn the event of a fault, consult
the interpretation of status
ET098 Driver's seat belt
contact and of command
AC009 Instrument panel
indicator lights.
TDB_V08_CCONF /TDB_V0C_CCONFTDB ph2 (EG/MG)
Prog version: 04xx
Vdiag No.: 08, 0C
MR-372-J84-83A000$441.mif
Page 23 of 63
83A-23
MR-372-J84-83A000$441.mif
V8
INSTRUMENT PANEL
Fault finding - Conformity check83A
TDB ph2 (EG/MG)
Prog version: 04xx
Vdiag No.: 08, 0C
DISPLAY
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Ignition on, engine off.
Order FunctionParameter, Status
Check or ActionDisplay and notes Fault finding
1Vehicle
speedPR099:Vehicle speedX mph (km/h)In the event of a fault, consult
the interpretation of parameter
PR099 Vehicle speed.
2
EnginePR116:Engine speedX rpmIn the event of a fault, consult
the interpretation of parameter
PR116 Engine speed.
3PR027:Coolant
temperature"X" ˚CIn the event of a fault, consult
the interpretation of parameter
PR027 Coolant temperature.
4
LightingPR111:Lighting dimmer
voltageIgnition on, dipped
headlights lit.
0.3 V < PR111 < 7 VIn the event of a fault, contact
the Techline.
5AC009:Instrument panel
warning lightsThe command lights
up all the indicator
lights at the same
time.In the event of a fault, consult
the interpretation of commands
AC009 Instrument panel
warning lights.
6AC010:LightingThe lighting intensity
will vary to 50% then
100% of its maximum
intensity for
5 seconds each time.In the event of a fault, consult
the interpretation of commands
AC010 Lighting.
7 Needle
gaugesAC008:Instrument panel
needle gaugesInstrument panel
needle gauge control.In the event of a fault, consult
the interpretation of command
AC008 Instrument panel
needles.
8Display AC007:DisplayThe display shows the
mileage as well as the
range.
All areas of the display
must light up at the
same time.In the event of a fault, consult
the interpretation of command
AC007 Display.
9Symbol
displayAC011:Symbol displayThe symbol display
shows the status of
the opening elements
and the tyre pressure.In the event of a fault, consult
the interpretation of command
AC011 Symbol display.
Page 40 of 63
83A-40
MR-372-J84-83A000$756.mif
V8
83A
INSTRUMENT PANEL
Fault finding - Command summary table
Tool command Diagnostic tool title
RZ001Fault memory
AC006Buzzer
AC007Display
AC008Instrument panel needle gauges
AC009Instrument panel warning lights
AC010Lighting
AC011Symbol display
VP002Write VIN
VP006Oil change frequency in km.
VP007Oil change frequency in months.
VP008Distance to next oil service: actual value in km
VP009Oil service interval: actual value in months
VP010Mileometer updating
VP011Fuel tank sender unit calibration
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
MR-372-J84-83A000$756.mif
Page 42 of 63
83A-42
MR-372-J84-83A000$819.mif
V8
INSTRUMENT PANEL
Fault finding - Interpretation of commands83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
AC007
DISPLAY
NOTESThere must be no present or stored faults.
Activate the display using command AC007 Display.
The display lights so you can check all the indicators and displays trip computer information.
If there is a display fault, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
Page 44 of 63
83A-44
MR-372-J84-83A000$819.mif
V8
INSTRUMENT PANEL
Fault finding - Interpretation of commands83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
AC009
INSTRUMENT PANEL WARNING LIGHTS
NOTESThere must be no present or stored faults.
Activate the instrument panel warning lights using command AC009 Instrument panel warning lights.
The indicator lights are all on, check that the lights are correct.
Check the condition and connection of the instrument panel 24-track grey connector.
If there is a repair method (see Technical note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair) repair the wiring, otherwise replace it.
Check the condition and connection of the 4-track seat belt warning module black connector.
If there is a repair method (see Technical note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair) repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Instrument panel grey connector, track 16 Track 3 of the seat belt warning module
connector
Instrument panel grey connector, track 23 Track 4 of the seat belt warning module
connector
Instrument panel grey connector, track 12 Track 1 of the seat belt warning module
connector
Instrument panel grey connector, track 11 Track 2 of the seat belt warning module
connector
If there is a repair method (see Technical note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair) repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.
Page 45 of 63
83A-45
MR-372-J84-83A000$819.mif
V8
INSTRUMENT PANEL
Fault finding - Interpretation of commands83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
AC010
LIGHTING
NOTESThere must be no present or stored faults.
Activate the instrument panel lighting using command AC010 Lighting.
The instrument panel lights up; change the lighting brightness.
If there is a lighting fault, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
Page 46 of 63
83A-46
MR-372-J84-83A000$819.mif
V8
INSTRUMENT PANEL
Fault finding - Interpretation of commands83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
AC011
DOT MATRIX DISPLAY
NOTESIMPORTANT
–Affects the opening elements indicator lights (on mid-range instrument panels).
–Affects tyre pressure monitor system warning lights (on mid-range instrument panel
if fitted to the vehicle).
–Affects automatic and sequential gearbox warning lights.
There must be no present or stored faults.
Activate the dot matrix display using command AC011 Dot matrix display.
The dot matrix display lights up.
If there is a lighting fault, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.