battery RENAULT SCENIC 2008 J84 / 2.G Electrical Equipment - Multimedia Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2008, Model line: SCENIC, Model: RENAULT SCENIC 2008 J84 / 2.GPages: 22, PDF Size: 0.07 MB
Page 6 of 22
86C-6
MR-372-J84-86C100$111.mif
V2
MULTIMEDIA
Fault finding - Introduction86C
5. FAULT FINDING LOG
You will always be asked for this log:
●when requesting technical assistance from Techline,
●for approval requests when replacing parts for which approval is mandatory,
●to be attached to monitored parts for which reimbursement is requested. The log is needed for warranty
reimbursement, and enables better analysis of the parts removed.
6. SAFETY INSTRUCTIONS
Safety rules must be observed during any work on a component to prevent any damage or injury:
–check the battery voltage to avoid incorrect operation of computer functions,
–Use the proper tools. IMPORTANTIMPORTANT
Any fault on a complex system requires thorough fault finding with the appropriate tools. The
FAULT FINDING LOG, which should be completed during the procedure, enables you to keep
track of the procedure which is carried out. It is an essential document when consulting the
manufacturer.
IT IS THEREFORE MANDATORY TO FILL OUT A FAULT FINDING LOG
EACH TIME IT IS REQUESTED BY TECHLINE OR THE WARRANTY DEPARTMENT.
Page 15 of 22
86C-15
MR-372-J84-86C100$777.mif
V2
MULTIMEDIA
Fault finding - Conformity check86C
SUB-FUNCTION: USER SELECTION (CONTINUED 2)
NOTESOnly carry out a conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on.
ComputerParameter, Status checked or
ActionDisplay and notes Fault finding
See 86D,
Multimedia network
interface unitET001:Activation signalACTIVE
INACTIVEIn the event of a fault, consult
ALP 2 "The multimedia
system does not switch on".
ET002:Radio on/off buttonACTIVE
INACTIVE
ET003:Timed battery
voltageACTIVE
INACTIVENONE
ET005:Silence modeACTIVE
INACTIVE
DECREASEIn the event of a fault, refer to
the interpretation of status
ET005 “Silence mode”.
ET006:User profile in
progress0/1/2/3/4NONE
ET008:Vehicle movement
directionFRONT
REAR
NEUTRALIn the event of a fault, refer to
the interpretation of status
ET008 "Vehicle movement
direction".
PR002:Battery voltage11 V < PR002 < 14 VIn the event of a fault, refer to
the interpretation of parameter
PR002 Battery voltage.
PR003:Vehicle speed0 mphIn the event of a fault, carry out
fault finding on the ABS system
(see 38C, ABS system).
PR001:Mileage last fault
appearedIn KmThe parameter PR001
"Mileage last fault appeared"
indicates the distance travelled
since the last fault appeared.
Page 18 of 22
86C-18
MR-372-J84-86C100$777.mif
V2
MULTIMEDIA
Fault finding - Conformity check86C
SUB-FUNCTION: AUDIO
NOTESOnly carry out a conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on.
ComputerParameter, Status checked or
ActionDisplay and notes Fault finding
See 86A, RadioPR010:Vehicle speedUnit: km/hIn the event of a fault, consult
the interpretation of parameter
PR010 Vehicle speed.
PR011:Battery voltage11 V < PR011 <
14 VIn the event of a fault, refer to
the interpretation of parameter
PR011 Battery voltage.
ET056:Auxiliary inputACTIVE
INACTIVEIn the event of a fault, consult
ALP 23 "Auxiliary source
fault".
ET057:Activation signalACTIVE
INACTIVEIn the event of a fault, carry out
fault finding on the multimedia
network interface unit (see
86D, Multimedia network
interface unit).