steering wheel RENAULT SCENIC 2008 J84 / 2.G LPN Radio Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2008, Model line: SCENIC, Model: RENAULT SCENIC 2008 J84 / 2.GPages: 93, PDF Size: 0.25 MB
Page 9 of 93
86A-9
MR-372-J84-86A050$177.mif
V3
86A
RADIO
Fault finding - Role of components
Role of main components
–Display: displays various multimedia system data such as the station selected, time, CD listing and satellite
guidance information.
–Steering column control: allows the various system functions to be used via the steering wheel control.
–Speakers and tweeters: relay the sound from the multimedia system into the vehicle.
–CD changer: enables compact discs to be loaded and music to be relayed to the receiver.
–AM/FM aerial: receives radio signals from various transmitters.
–GPS aerial: receives various data transmitted by satellites.
–Radio/navigation computer: manages the various multimedia system functions according to user requests and
transmits audio data to the vehicle via the speakers.
–Cartographic map DVD: loads maps into the navigation computer.
–AM/FM aerial amplifier: improves the reception of AM/FM signals.
–Multimedia network interface unit: enables information to be exchanged between the "vehicle" and "multimedia"
multiplex networks. This computer is involved in activating the multimedia system.
MR-372-J84-86A050$177.mif
LPN RADIO
Vdiag No: C4
Page 10 of 93
86A-10
MR-372-J84-86A050$236.mif
V3
86A
RADIO
Fault finding - Operating diagram
Layout of the main components of the LPN* Radio system:
*LPN: Low Price NavigationV M multiplex line
diagnostic socketUCH
FEED (Kangoo 2)Electric mirror,
passenger side
(Trafic II ph2)
Other computersMultimedia network
interface unit
Multifunction aerial
(Trafic II ph2)Steering column
control
GPS aerialLPN* radio
navigation
Aerial amplifier
(Espace IV ph2,
Scénic II ph2,
Kangoo 2)Passenger
compartment fuse
box and relay
ABS, ABS/ESP or
wheel speed
computer depending
on equipment levelRadio navigation
display
Microphone
CD changer
(if an option)Speakers
Vehicle multiplex network
Multimedia multiplex network
MR-372-J84-86A050$236.mif
LPN RADIO
Vdiag No: C4
Page 13 of 93
86A-13
MR-372-J84-86A050$413.mif
V3
86A
RADIO
Fault finding - Replacement of components
For information on removing/refitting the LPN* radio navigation computer, refer to the MR for the vehicle concerned:
–Scénic II ph2 (see MR 370, Mechanical, 83C On-board telematics system, Navigation computer: Removal -
Refitting)
–Espace IV ph2 (see MR 405, Mechanical, 83C, On-board telematics system, Radio navigation:
Removal - Refitting)
–Trafic II ph2 (see MR 408, Mechanical, 83C, On-board telematics system, Radio navigation:
Removal - Refitting)
–Kangoo 2 (see MR 417, Mechanical, 83C On-board telematics system, Radio navigation:
Removal - Refitting)
Operations to be carried out before replacing the LPN* radio navigation computer:
Note:
If the LPN* radio navigation computer and the multimedia network interface unit are replaced
simultaneously, first configure the multimedia network interface unit (see 86D, multimedia network interface
unit, Configuration and programming).
1 -Before replacing the LPN* radio navigation computer (with Techline approval), perform a fault read and a
conformity check to confirm that it is defective.
2 -Before removing, eject the CD.
3 -After obtaining Techline approval, remove the LPN* radio navigation computer with the ignition off (wait
1 minute for the system to shut down completely).
The LPN* radio navigation computers available from the Parts Department are supplied unconfigured.
Operations to be carried out after replacing the LPN* radio navigation computer:
1. Configure the computer (see Configurations and Programming).
The LPN* radio navigation computer is in factory mode following configuration (FM 87.5 MHz in scrambled mode for
2 minutes).
Clear the present or stored faults using command RZ003 Fault memory.
2. Enter the unlocking code for the LPN* radio navigation system
How to obtain the unlocking code for the LPN* radio navigation system:
–switch on + after ignition feed (see Introduction),
–if the LPN* radio navigation system does not switch on when the + after ignition feed is activated, press the ON/
OFF button on the front panel,
–connect the Clip diagnostic tool,
–note the programming key number ID007 Radio programming key shown in the Identification menu.
–When you have this programming key number, consult Renault.net to obtain the LPN* radio navigation system
unlocking code. If the fault is still present, contact Techline.
–The unlocking code is requested 2 minutes after the LPN* radio navigation system has been switched on,
–enter the code using the radio control satellite under the steering wheel.
Important: After activating the system, the delay before establishing dialogue can last 20 seconds.
*LPN: Low Price NavigationNote:
Each time an incorrect code is entered, the waiting time doubles (maximum 32 minutes).
MR-372-J84-86A050$413.mif
LPN RADIO
Vdiag No.: C4
Page 77 of 93
86A-77
MR-372-J84-86A050$944.mif
V3
LPN RADIO
Vdiag No.: C4RADIO
Fault finding - Fault Finding Chart86A
ALP 10 No radio and/or CD sound
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Ensure there are no present or stored faults.
Use the wiring diagrams Technical Note for Scénic II ph2, Espace IV ph2,
Trafic II ph2 or Kangoo 2.
The message PAUSE is displayed on the radio display.
NO
Check the condition of the MUTE button on the steering wheel control (see 86D, Multimedia network interface
unit).
Check the FADER setting:
In the AUDIO settings menu (SET button). Select the "audio" and "fader" menus, then adjust the fader by
moving the cursor using the central wheel on the front panel.
Has the fault disappeared?
NO YES
Run the commands to test the speakers (see
Command summary table).
Has the fault disappeared?
NO YES
Contact the Techline.
End of fault finding.
End of fault finding.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
LPN_VC4_ALP10