ESP RENAULT SCENIC 2008 J84 / 2.G Parking Distance Control Workshop Manual

PARKING DISTANCE CONTROL
Fault finding - Introduction
87F
87F - 2V4 MR-372-J84-87F000$066_eng.mif
187F
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this manual):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM), paper.
Type of diagnostic tools
–CLIP + multiplex line sensor
Special tooling required
3. RECAP
To run fault finding on the vehicle computers, switch on the ignition.
Depending on the type of vehicle equipment, proceed as follows:
To cut off the + after ignition feed, proceed as follows:Vehicle(s): CLIO III, Laguna II ph 1 and 2
Vel-Satis ph1 and 2,
Espace IV ph1 and 2,
Mégane II, Scénic II, Modus ph2Computer name: Parking distance control
Vdiag No: 04-08
Special tooling required
Multimeter
Elé. 1681 Universal bornier
For vehicles with radio frequency remote control/key,
switch on the ignition with the key.
For vehicles with a Renault card,
with the vehicle card in the card reader,
press and hold start button (longer than 5 seconds) with start-up conditions not fulfilled,
connect the diagnostic tool and perform the required operations.
For vehicles with key/radiofrequency remote control, use the key to switch off the ignition.
For vehicles with a Renault card,
press the Start button twice briefly (less than 3 seconds),
ensure that the + after ignition feed has been cut off by checking that the computer indicator lights on the
instrument panel have gone out.
AAP_V04_PRELI/AAP_V08_PRELI
MR-372-J84-87F000$066_eng.mif

PARKING DISTANCE CONTROL
Fault finding - Introduction
87F
87F - 3V4 MR-372-J84-87F000$066_eng.mif
Vdiag No: 04-08
Faults
Faults are declared as either present or stored (depending on whether they appeared in a certain context and have
disappeared since, or whether they remain present but have not been diagnosed within the current context).
The present or stored status of faults should be taken into consideration when the diagnostic tool is used following
the + after ignition supply being switched on (without operating the system components).
For a present fault, apply the procedure described in the Interpretation of faults section.
For a stored fault, note the faults displayed and apply the instructions in the Notes section.
If the fault is confirmed when the instructions in the Notes section are applied, the fault is present. Deal with the fault
If the fault is not confirmed, check:
–the electrical lines which correspond to the fault,
–the connectors for these lines (for oxidation, bent pins, etc.),
–the resistance of the component detected as faulty,
–the condition of the wires (melted or split insulation, wear).
Conformity check
The aim of the conformity check is to check data that does not produce a fault on the diagnostic tool because the
data is inconsistent. Therefore, this stage is used to:
–carry out fault finding on faults that do not have a fault display, and which may correspond to a customer
complaint.
–check that the system is operating correctly and that there is no risk of a fault recurring after repairs.
This section gives the fault finding procedures for statuses and parameters and the conditions for checking them.
If a status is not behaving normally or a parameter is outside the permitted tolerance values, consult the
corresponding fault finding page.
Customer complaints - Fault finding chart
If the test with the diagnostic tool is OK but the customer complaint is still present, the fault should be processed by
customer complaint.
A synopsis of the general procedure to follow is provided on the following page
in the form of a flow chart.

PARKING DISTANCE CONTROL
Fault finding - Introduction
87F
87F - 5V4 MR-372-J84-87F000$066_eng.mif
Vdiag No: 04-08
4. FAULT FINDING PROCEDURE (continued)
Wiring check
Fault finding problems
Disconnecting the connectors and/or manipulating the wiring harness may temporarily remove the cause of a fault.
Electrical measurements of voltage, resistance and insulation are generally correct, especially if the fault is not
present when the analysis is made (stored fault).
Visual inspection
Look for damage under the bonnet and in the passenger compartment.
Carefully check the fuses, insulators and wiring harness routing.
Look for signs of oxidation.
Tactile inspection
While manipulating the wiring harness, use the diagnostic tool to note any change in fault status from stored to
present.
Make sure that the connectors are properly locked.
Apply light pressure to the connectors.
Twist the wiring harness.
If there is a change in status, try to locate the source of the fault.
Inspection of each component
Disconnect the connectors and check the appearance of the clips and tabs, as well as the crimping (no crimping on
the insulating section).
Make sure that the clips and tabs are properly locked in the sockets.
Check that no clips or tabs have been dislodged during connection.
Check the clip contact pressure using an appropriate model of tab.
Resistance check
Check the continuity of entire lines, then section by section.
Look for a short circuit to earth, to + 12 V or to another wire.
If a fault is detected, repair or replace the wiring harness.

PARKING DISTANCE CONTROL
Fault finding - Allocation of computer tracks87F
87F - 8V4 MR-372-J84-87F000$198_eng.mif
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Allocation of computer tracks
Computer with 1 connector (Clio III, Laguna II ph1 and 2, Vel Satis ph1 and 2 Espace IV ph 1 and 2 Mégane II,
Scénic II, Modus ph2):
Track Description
1+ 12 V after ignition feed
2+ 12 V buzzer
3Computer earth
4Reverse gear signal (+ 12 V)
5Warning light control
6Buzzer earth
7Not used
8Diagnostic line K
9+ 12 V rear sensors
10 Rear sensors earth
11 Not used
12 Parking distance control On/Off switch signal
13 Right-hand inner sensor signal
14 Left-hand inner sensor signal
15 Left-hand outer sensor signal
16 Right-hand outer sensor signal
Note:
For Scénic II, the computer and buzzer are located on the left-hand side of the luggage compartment behind the
interior trim.
MR-372-J84-87F000$198_eng.mif

PARKING DISTANCE CONTROL
Fault finding - Allocation of computer tracks87F
87F - 9V4 MR-372-J84-87F000$198_eng.mif
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Allocation of computer tracks
Computer with 2 connectors (Laguna II ph1, Vel Satis ph1, Espace IV ph1):
12-TRACK CONNECTOR
16-TRACK CONNECTORTrack Description
1Not used
2Right-hand inner sensor signal
3Left-hand inner sensor signal
4Right-hand outer sensor signal
5Left-hand outer sensor signal
6Not used
7Not used
8Rear sensors earth
9Not used
10 Not used
11 + 12 V rear sensors
12 Not used
Track Description
1+ 12 V after ignition
2Buzzer earth
3Not used
4Parking distance control On/Off switch signal
5Not used
6Reverse gear signal (+ 12 V)
7Not used
8Computer earth
9Not used
10 + 12 V buzzer
11 Not used
12 Diagnostic line K
13 Warning light control
14 Not used
15 Not used
16 Not used

PARKING DISTANCE CONTROL
Fault finding - Fault summary table87F
87F - 12V4 MR-372-J84-87F000$396_eng.mif
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Fault summary table
Summary of sensors and actuators on which fault finding can be performed by the parking distance control computer
(with corresponding Design Office codes)
Tool fault Associated DTC Diagnostic tool title
DF002 9001Left-hand outer sensor
DF003 9002Left-hand inner sensor
DF004 9004Right-hand outer sensor
DF005 9003Right-hand inner sensor
DF006 9006Buzzer
DF007 9007Sensor feed voltage
DF008 9005Computer fault
DF012 9009Parking distance control switch indicator light
MR-372-J84-87F000$396_eng.mif

PARKING DISTANCE CONTROL
87F
87F - 27V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08
Fault finding - Interpretation of faults
DF012
PRESENT
OR
STOREDPARKING DISTANCE CONTROL SWITCH INDICATOR LIGHT
CC.0 : short circuit to earth or open circuit
CO.1 : open circuit or short circuit to + 12 volts
NOTESConditions for applying the fault finding procedure to stored faults:
A fault is declared present after reverse gear is engaged and the parking distance
control deactivation switch is pressed.
Remove the parking distance control switch and check the connections and condition of its connector.
Repair if necessary.
Check for an earth on track B3 of the parking distance control switch connector.
Repair if necessary.
Switch off the ignition, and disconnect the parking distance control computer 16-track connector to check the
insulation and continuity and the absence of interference resistance on the following connection:
Laguna II ph2, Espace IV ph2, Vel-Satis ph2, Mégane II, Scénic II, Laguna II ph1 (1 connector),
Espace IV ph1 (1 connector), Vel-Satis ph1 (1 connector), Laguna II ph1 (2 connectors),
Vel- Satis ph1 (2 connectors), Clio III, Modus ph2:
Parking distance control switch connector Parking proximity sensor computer connector
Track B2 Track 5
Repair if necessary.
Espace IV ph1 (2 connectors):
Parking distance control switch connector16-track parking distance control computer
connector
Track B2 Track 13
Repair if necessary.
If the fault is still present, replace the parking distance control switch.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.
AAP_V04_DF012/AAP_V08_DF012

PARKING DISTANCE CONTROL
Fault finding - Interpretation of statuses
87F
87F - 31V4 MR-372-J84-87F000$660_eng.mif
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Interpretation of statuses
1 connector:ET001
REVERSE GEAR ENGAGED
NOTESSpecial note:
Only carry out the checks if the YES and NO statuses are not consistent with the
position of the gear lever.
Check that the reversing lights are working correctly: they should come on when reverse gear is selected and go
out when it is not.
If the reversing lights fail to function as specified:
With the ignition switched off, disconnect the parking distance control computer connector to check the
insulation (against + 12 V), and the continuity and absence of interference resistance on the following
connection:
Laguna II ph1 ph2, Espace IV ph1 ph2, Vel-Satis ph2, Clio III, Modus ph2:
Parking distance control computer connector Rear lights connector
Track 4 Track 3
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
Vel-Satis ph1, Scénic II:
Parking distance control computer connector Rear left hand lights connector
Track 4 Track 2
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.
AAP_V04_ET001/AAP_V08_ET001
MR-372-J84-87F000$660_eng.mif

PARKING DISTANCE CONTROL
Fault finding - Interpretation of statuses
87F
87F - 33V4 MR-372-J84-87F000$660_eng.mif
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Interpretation of statuses
2 connectors:ET001
(CONTINUED 2)
Only for estates:
Parking distance control computer connector
(white)Left-hand rear light connector
Track 4 Track 5
Parking distance control computer connector
(white)Right-hand rear light connector
Track 4 Track 5
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
Laguna II ph1, Espace IV ph1, Vel-Satis ph2, Clio III:
Parking distance control computer connector Rear light connector
Track 6 Track 3
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
Vel Satis ph1:
Parking distance control computer connector Rear light connector
Track 6 Track 2
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.

PARKING DISTANCE CONTROL
Fault finding - Interpretation of statuses
87F
87F - 34V4 MR-372-J84-87F000$660_eng.mif
Vdiag No: 04-08
ET002
BUZZER CONTROL
NOTESThere must be no present or stored faults.
ET002
remains OFF
ET002
ON but buzzer does
not sound
Check that the parking distance control system is switched on using status ET003
"Parking distance control function" (parking distance control switch warning light
goes out). If the status displays “suspended” or “deactivated”, restart the system by
pressing for 1 or 3 seconds, consult the interpretation of status ET003 “Parking
distance control function”.
Check that the parking distance control configuration is correct for the vehicle on
which it is fitted (LC005 Vehicle identification). If necessary, reconfigure the
computer using command CF005 Vehicle identification.
Check, when the vehicle is close to an obstacle (between 20 and 150 cm), that the
distance evaluated corresponds to the distance displayed by the diagnostic tool
(PR001 to PR004).
If the distance reading does not match or the distance parameters stay at 255 cm,
contact your Techline.
Check that the buzzer volume is not at a zero setting LC001 Buzzer volume.
If the configured volume is ZERO or DEACTIVATED, reconfigure the computer using
command CF001 Buzzer volume. Select the volume required by the customer.
Switch off the ignition, and disconnect the parking distance control computer 16-track
connector to check the insulation and continuity and ensure the absence of
interference resistance on the following connections:
Laguna II ph2, Espace IV ph2, Espace IV ph1 (1 connector), Vel-Satis ph2,
Vel-Satis ph1 (1 connector), Laguna II ph1 (1 connector),
Parking distance control computer Buzzer
Track 2 Track 1
Track 6 Track 2
Repair if necessary (refer to vehicle wiring diagrams).
AFTER REPAIRRepeat the conformity check from the start.
AAP_V04_ET002/AAP_V08_ET002