window RENAULT SCENIC 2008 J84 / 2.G Passenger Comparment Connection Unit Service Manual

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 340
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 340V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP24
CONTINUED 4
Is the control correct?
YES
Disconnect the sunroof motor connector (see MR Mechanical, 87D Electric windows - sunroof, Sunroof motor:
Removal - Refitting).
Check for + 12 V between connections BP93 and MAM of component 304.
Is the feed correct?
YESNO
Using the wiring diagram which corresponds to the vehicle, check the conformity of union R301.
Disconnect the sunroof motor connector (see MR Mechanical systems, 87D Electric windows-
sunroof, Sunroof motor: Removal - Refitting) and disconnect union R301.
Check the continuity of the following connections:
●Connection code MAM.
●Connection code BP93 between components 304 and R301.
If the continuity is faulty, check the intermediate connector R339.
If one of the connectors is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
After repairing the condition of the wiring, initialise the sunroof (see MR fault finding 87D, Electric
sunroof: Initialisation).
If the fault is still present, contact the Techline.
NOReplace the control (see MR Mechanical
systems, 87D Electric windows -
sunroof, Sunroof switch: Removal -
Refitting).
AFTER REPAIRCarry out a complete check using the diagnostic tool.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 341
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 341V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP24
CONTINUED 5
Check using status ET087 Sunroof/one touch window authorisation that authorisation for the UCH to open the
sunroof is ACTIVE.
Disconnect the sunroof motor connector (see MR Mechanical, 87D Electric windows - sunroof, Sunroof motor:
Removal - Refitting).
Check for + 12 V between connections BP93 and 21K of component 304.
Is the feed correct?
NOYES
Disconnect the sunroof motor connector (see MR Mechanical systems, 87D Electric windows-
sunroof, Sunroof motor: Removal - Refitting) and disconnect union R301.
Check the continuity on the following connection:
●Connection code 21K between components 304 and 645.
If the continuity is faulty, use the wiring diagram corresponding to the vehicle to check
intermediate connectors R339 and R301.
If one of the connectors is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace
the wiring.
After repairing the condition of the wiring, initialise the sunroof (see MR fault finding 87D, Electric
sunroof: Initialisation).
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check using the diagnostic tool.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 342
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 342V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP24
CONTINUED 6
Check the continuity and insulation of the following connections:
●Connection code 52J.
●Connection code 52H.
●Connection code 52G between components 304 and R301.
If the continuity is faulty, use the wiring diagram corresponding to the vehicle to check the conformity of
intermediate connector R339.
If one of the connectors is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
After repairing the condition of the wiring, initialise the sunroof (see MR fault finding 87D, Electric sunroof:
Initialisation).
If the continuity and insulation of the following connections are correct: Replace the sunroof motor (see 87D
Electric windows - sunroof: Removal - Refitting).
Control positionConnections 52D and
52HConnections 52D and
52JConnections 52D and
52G
Closed 100 ΩΩ Ω Ω
Max.100 ΩΩ Ω Ω
Max. Infinite
Tilt position Infinite100 ΩΩ Ω Ω
Max. Infinite
Sliding position 1Infinite100 ΩΩ Ω Ω
Max.100 ΩΩ Ω Ω
Max.
Sliding position 2Infinite Infinite100 ΩΩ Ω Ω
Max.
Sliding position 3 100 ΩΩ Ω Ω
Max. Infinite100 ΩΩ Ω Ω
Max.
Pressed 100 ΩΩ Ω Ω
Max.100 ΩΩ Ω Ω
Max.100 ΩΩ Ω Ω
Max.
AFTER REPAIRCarry out a complete check using the diagnostic tool.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 343
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 343V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP25 No sunroof opening position 1, 2 or 3
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
For vehicles with Mégane II phase 2 bodywork, (see 87D Electric windows -
Sunroof, Fault finding chart).
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Does the sunroof operate in at least one of the
control positions?
YES
Disconnect the sunroof switch and check its
conformity and correct operation using a multimeter
and the table below.
Control positionConnections 52D and
52HConnections 52D and
52JConnections 52D and
52G
Closed 100 ΩΩ Ω Ω
Max.100 ΩΩ Ω Ω
Max. Infinite
Tilt position Infinite100 ΩΩ Ω Ω
Max. Infinite
Sliding position 1Infinite100 ΩΩ Ω Ω
Max.100 ΩΩ Ω Ω
Max.
Sliding position 2Infinite Infinite100 ΩΩ Ω Ω
Max.
Sliding position 3 100 ΩΩ Ω Ω
Max. Infinite100 ΩΩ Ω Ω
Max.
Pressed 100 ΩΩ Ω Ω
Max.100 ΩΩ Ω Ω
Max.100 ΩΩ Ω Ω
Max.
NOSee ALP24.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP25 /UCH_V48_ALP25/UCH_V4C_ALP25/
UCH_V4D_ALP25/UCH_V4F_ALP25/UCH_V50_ALP25

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 344
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 344V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP25
CONTINUED
Is the control correct?
YES
Check the continuity and insulation of the following connections:
●Connection code 52J.
●Connection code 52H.
●Connection code 52G between components 304 and R301.
If the continuity is faulty, use the wiring diagram corresponding to the vehicle to check the conformity of
intermediate connector R339.
If one of the connectors is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
After repairing the condition of the wiring, initialise the sunroof (see MR fault finding 87D, Electric sunroof:
Initialisation).
If the continuity and insulation of the following connections are correct: Replace the sunroof motor (see 87D
Electric windows - sunroof: Removal - Refitting).
NOReplace the control (see MR Mechanical
systems, 87D Electric windows -
sunroof, Sunroof switch: Removal -
Refitting).
AFTER REPAIRCarry out a complete check using the diagnostic tool.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 345
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 345V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP26The sunroof is difficult to close or the anti-pinch is triggered
without any apparent obstacles
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
For vehicles with Mégane II phase 2 bodywork, (see MR 366, Fault finding, 87D
Electric windows - Sunroof, Fault finding chart).
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Initialise the sunroof (see MR fault finding 87D Electric sunroof: Initialisation).
Has the fault been solved?
YESNO
End of fault finding.
Open the sunroof fully (if not possible, see Defect mode and
safe mode).
Remove the sunroof motor (see MR 364 Mechanical, 87D
Electric windows - Sunroof, Sunroof motor: Removal -
Refitting).
Slide the moving panel of the sunroof manually.
Does the moving panel slide without a point of
resistance?
NO YES
Replace the sunroof motor (see 87D Electric windows -
Sunroof: Removal - Refitting).
Remove the moving sunroof panel
(see MR Bodywork, 52A, Non-side opening
element mechanisms, Mobile sunroof
panel: Removal - Refitting).
Visually check that no foreign bodies
(sand, leaves, etc.) are present in the rails.
Are there any foreign bodies in the rails?
YES NO
Clean the mechanism and the rails with an air gun. Refit the sunroof mobile panel (see MR 365 Bodywork, 52A,
Non-side opening element mechanisms, Moving sunroof panel: Removal - Refitting).
Initialise the sunroof (see MR fault finding 87D Electric sunroof: Initialisation).
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP26 /UCH_V48_ALP26/UCH_V4C_ALP26/
UCH_V4D_ALP26/UCH_V4F_ALP26/UCH_V50_ALP26

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -363
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -363V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP38 Windows fail to close after two locking requests
NOTESMake sure the vehicle is indeed equipped with a sequential-control window lift.
Make sure status ET087 One-touch electric window authorisation is ACTIVE.
See the treatment for this status if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP38 /UCH_V48_ALP38/UCH_V4C_ALP38/
UCH_V4D_ALP38/UCH_V4F_ALP38/UCH_V50_ALP38