display RENAULT SCENIC 2009 J84 / 2.G Engine And Peripherals EDC16 User Guide

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-42V3 MR-372-J84-13B250$315.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF008
CONTINUED 3
2.DEF
NOTESThe brake pedal has been depressed while the accelerator
is depressed and jammed.
Check the brake light switch.
This is a test procedure designed to detect an accelerator pedal that is jammed in the depressed position. It
monitors the accelerator pedal in relation to the brake pedal.
If the test procedure detects depression of the brake pedal over 600 ms, it registers a fault which is stored in the
computer. While this fault is present (both pedals depressed simultaneously) the engine switches to limp home
mode and the engine speed is set at 1,400 rpm.
Once the fault is no longer present (e.g. brake and accelerator pedals released) safe mode is deactivated and the
engine immediately regains its ability to respond to speed/torque requests.
This fault may occur even if the accelerator pedal is not jammed, if there is driver error during use:
- "Heel-and-toe" type driving,
- Vehicle with driving school option,
The procedure in this case should be to clear the fault and take another reading.
If the fault is still present, check the mechanical condition of the accelerator pedal:
–locked in full load position,
–with the pedal blocked by an external component.
Repair if necessary.
Vary the position of the pedal and refer to the conformity check in order to check the operating values of the
accelerator pedal potentiometer.
If the values displayed are inconsistent, replace the accelerator pedal potentiometer.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-57V3 MR-372-J84-13B250$315.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF037
PRESENT
OR
STOREDENGINE IMMOBILISER
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after an attempt to start engine.
Special notes:
It is impossible to start the vehicle.
If the fault is present, the level 2 warning light will light up.
Use bornier Ele. 1681 or Ele. 1590 for any operation on the injection computer
connectors.
Check the UCH connections.
Check the injection computer connections.
Repair if necessary.
Test the multiplex network (see 38B, Multiplexing) and carry out a complete fault finding on the UCH.
Refer to the UCH Technical Note (see 87B, Passenger compartment connection unit) if the fault is displayed
as present.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V51_DF037

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-60V3 MR-372-J84-13B250$315.mif
DF038
CONTINUED 2
11.DEF
NOTESIf there are a number of faults, deal with the other system
faults first.
Display the stored context for fault DF038.
PR142 Computer fault = 10
NO YES
Main screen parameters
PR071 Computer supply voltage > 10 V
YES
Contexts stored from DF038
PR071 Computer supply voltage > 10 V
YES
Check the condition of the wiring harness between the
computer and the battery, carry out the necessary repairs.
–Start the vehicle.
–Clear the stored faults.
–Check the faults:
–If DF038 is stored, end fault finding.
–If DF038 is present, contact the Techline.
NO
Check the charge circuit and carry out the
necessary repairs:
–Check the condition of the battery
terminals.
–Carry out fault finding on the alternator.
Recharge or replace the battery.
EDC16
PROGRAM No.: C1
Vdiag No.: 51
Contact the Techline
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-62V3 MR-372-J84-13B250$360.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF039
CONTINUED
Measure the air temperature sensor resistance between tracks 1 and 2 of the air flow sensor.
Replace the air flowmeter if the resistance displayed is not:
3714 ± 161 Ω at 10˚C
2448 ± 96 Ω at 20˚C
1671 ± 59 Ω at 30˚C
CC.0
NOTESNone
Check the air flowmeter connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity and insulation against earth of the connection between:
Injection computer brown 48-track connector B, track G2 Track 1 air flowmeter connector
Injection computer brown 48-track connector B, track E2 Track 2 air flowmeter connector
Injection computer brown 48-track connector B, track B4 Track 3 air flowmeter connector
Injection supply relay mounting Track 5 track 4 air flow sensor connector
Repair if necessary.
Measure the air temperature sensor resistance between tracks 1 and 2 of the air flow sensor.
Replace the air flowmeter if the resistance is not approximately:
3714 ± 161 Ω at 10˚C
2448 ± 96 Ω at 20˚C
1671 ± 59 Ω at 30˚C
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-73V3 MR-372-J84-13B250$360.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF049
PRESENT
OR
STOREDREFRIGERANT SENSOR CIRCUIT
CC.1 : Short circuit to + 12 V
CO.0 : Open circuit or short circuit to earth
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present following a road test, or if the air conditioning is
switched on.
Special notes:
If the fault is present, air conditioning is not authorised.
Use bornier Ele. 1681 or Ele. 1590 for any operation on the injection computer
connectors.
CC.1
NOTESNone
Check the refrigerant pressure sensor connectors.
Check the injection computer connections.
Repair if necessary.
Check that the configuration reading LC009 Air conditioning is WITH.
If LC009 is WITHOUT, run command RZ005 Programming to reinitialise the vehicle configurations.
If necessary, operate the air conditioning to reconfigure the computer to WITH.
Connect an air conditioning filling station (equipped with a high pressure gauge) to the vehicle.
Display parameter PR037 Refrigerant pressure and compare the value displayed by the filling station.
If the values match, run fault finding on the air conditioning (see 62A, Air conditioning).
If the values do not match, check the continuity and insulation against + 12 V of the following connections:
Injection computer brown 48-track connector B, track F1 Track C refrigerant sensor connector
Injection computer brown 48-track connector B, track F3 Track B refrigerant sensor connector
Injection computer grey 32-track connector C, track C3 Track A refrigerant sensor connector
Repair if necessary.
If the fault is still present, replace the refrigerant pressure sensor.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V51_DF049

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-74V3 MR-372-J84-13B250$360.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF049
CONTINUED
CO.0
NOTESNone
Check the refrigerant pressure sensor connectors.
Check the injection computer connections.
Repair if necessary.
Check that the configuration reading LC009 Air conditioning is WITH.
If LC009 is WITHOUT, run command RZ005 Programming to reinitialise the vehicle configurations.
If necessary, operate the air conditioning to reconfigure the computer to WITH.
Connect an air conditioning filling station (equipped with a high pressure gauge) to the vehicle.
Display parameter PR037 Refrigerant pressure and compare the value displayed by the filling station.
If the values match, carry out a fault finding procedure as described in the fault finding note for that vehicle.
If the values do not match, check the continuity and insulation against earth of the following connections:
Injection computer brown 48-track connector B, track F1 Track C refrigerant sensor connector
Injection computer brown 48-track connector B, track F3 Track B refrigerant sensor connector
Repair if necessary.
If the fault is still present, replace the refrigerant pressure sensor.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-80V3 MR-372-J84-13B250$360.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF053
CONTINUED 2
1.DEF
NOTESNone
Ch eck the rail pressure regulator connectors.
Ch eck the in jection computer connections.
Ch eck the lo w p ressu re circu it b y runningtest 2Low pressure circuit check.
Ch eck the conformityof the fuel used by applyingtest 10 Diesel f uel conformity check.
Ch eck the in jector return flow, runtest 8 Poor injector operation.
Ch eck theoperation of the overpressure valve if fitted to the vehicle, run test11 Incorrectopera tion of the
ov erpressure valve.
Re pair if n ecessa ry.
Measure theresistanceof the rail press u r e regulator betweentracks 1 and 2.
If the resistance is not3±1Ωat20˚C,replacetheinjection pump.
Ch eckthe continuity and absence of interference resistanceof the followingconnections:
Injection computer brown 48-track
connectorB,track M4Track 2 of the rail pressure regulator (fuel flow actuator)
Injection supply relay mountingtrack 5 track 1 of the rail pressure regulator (fuel flow actuator)
Re pair if n ecessa ry.
Ch eck the rail pressuresensor using the interpretation ofDF0 07 Rail pressure sensor circuit.
Re pair if n ecessa ry.
If the fault isstill present,check t hat thecomputeroutput is working correctly.
●Either using anammeter:
With the regulator connected, connect the current clamp to the regulator'strack 1connection,respecting t he
direction of the current.
Cle ar a ny rail pressure sensor faults and use commandAC011 Rail pressureregulator.
Th eammeter should display ten cycles of two successive currents:~0.6Athen~2A.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-81V3 MR-372-J84-13B250$360.mif
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16
PROGRAM No.: C1
Vdiag No.: 51
*Opening cyclic ratioDF053
CONTINUED 3
●Or usingavoltmeter:
With the regulator connected, connect the negative terminal of the voltmeter totrack 2of the rail pressure regulator
and thepositive terminal totrack 1.Clear any fuel pressure solenoid valve faults, then run commandAC011 Rail
pressure re gulator:
Thevoltmeter should display two successive voltage readings:
~3.15voltsfor an opening cycle ratio of 25% then~9.45Vfor an opening cycle ratio of 75% (ten cycles).
●Or using an oscillos cope(at 5 V range/division a nd 1 ms/div tim e base):
With the regulator connected, connect the negative terminal of the oscill oscope to the battery earth and the positive
terminal totrack 2of the fuel pressure solenoid valve, clear any r ail pressure regulator faults, and r un command
AC0 11 R ail pressure regulator:
theoscillo sco pe sh ould disp lay a square pulse signal with an a mplitude o f 1 2.5 V at a frequency of 1 85 Hz (with a n
OCR* alternating successively from 25 to 75%).
if the measurement does not show any control or continuous voltage, contact the techline.

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-83V3 MR-372-J84-13B250$360.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF053
CONTINUED 5
In the event of rail overpressure:
Check the operation of the injectors: refer to test 8 Poor injector operation.
Check that the rail pressure sensor is operating correctly using command AC011 Rail pressure regulator. Display
parameter PR038 Rail pressure, and refer to the conformity check to check the operating values.
If these checks do not reveal any faults, and if the fault is still present, replace the injection pump.
in the event of rail underpressure:
Check that the rail pressure sensor is operating correctly using command AC011 Rail pressure regulator. Display
parameter PR038 Rail pressure, and refer to the conformity check to check the operating values.
Check the low pressure diesel circuit priming.
Check the conformity of the diesel filter connections.
Check the condition of the filter (clogging and water saturation).
Check that there are no air bubbles between the filter and the high pressure pump.
Check the low and high pressure diesel fuel circuit sealing (visual inspections, odour, etc.): pump housing,
pressure relief valve, pipes, rail and injector unions, injector wells, etc.
Check the operation of the injectors: refer to test 8 Poor injector operation.
Carry out the necessary operations.
If the fault is still present, replace the injection pump.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.

DIESEL INJECTION
Fault finding – Interpretation of faults13B
13B-84V3 MR-372-J84-13B250$360.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
DF054
PRESENT
OR
STORED
TURBOCHARGING SOLENOID VALVE CONTROL CIRCUIT
CC.1 : Short circuit to + 12 V
CC.0 : Short circuit to earth
CO : Open circuit
1.DEF : Internal electronic fault
2.DEF : Inconsistent signal
3.DEF : Below minimum threshold
4.DEF : Above maximum threshold
5.DEF : Permanent high signal
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after:
–the engine is started,
–a road test,
–actuator command AC004 Turbocharging solenoid valve.
Special notes:
If the fault is present:
–turbocharging is no longer authorised,
–the EGR function is inhibited,
–the vehicle performance is reduced,
–the level 1 warning light is lit,
–If CC.0 is present, the OBD warning light will come on after three consecutive driving
cycles (starting + 5 seconds + switching off the ignition and waiting for 1 minute).
Use bornier Ele. 1681 or Ele. 1590 for any operation on the injection computer
connectors.
CC.1
4.DEF
5.DEF
NOTESNone
Check the turbocharging solenoid valve connections.
Check the injection computer connections.
Repair if necessary.
Measure the resistance of the turbocharging solenoid valve between tracks 1 and 2:
If the resistance displayed is not 15.4 ± 0.7 Ω at 20˚C, replace the turbocharger solenoid valve.
Check the continuity and insulation from the + 12 V feed of the following connection:
Injection computer grey 32-track connector C,
track E1Track 1 turbocharging solenoid valve
Repair if necessary.
If the fault is still present, replace the turbocharging solenoid valve.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V51_DF054