ESP RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Repair Manual

13B-228
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR038
RAIL PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the rail pressure in bar.
NOTESNo faults should be present or stored.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (starting faults, poor performance, stalling, etc.).
– after interpretation of command AC225 Rail pressure regulator.
Special notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on.
The rail pressure value is between:
0 < PR038 < 10 bar
Default value: 250 bar.
In the event of a fault, consult the interpretation of fault DF007 Rail pressure sensor circuit.
Conformity check with engine running, engine coolant temperature > 80°C.
The rail pressure value is (engine at idle speed):
PR038 = ~ 315 bar
Default value: 250 bar.
In the event of a fault, consult the interpretation of fault DF007 Rail pressure sensor circuit.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR038/EDC16_V58_PR038/EDC16_V5C_PR038/EDC16_V18_PR038/EDC16_V1C_PR038/EDC16_V20_PR038

13B-230
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR041
TURBOCHARGING PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the turbocharging pressure in mbar.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80 °C.
The turbocharging pressure value is:
PR041 = PR035 “Atmospheric pressure” ± 10 mbar
In the event of a fault, apply the interpretation of DF004 Turbocharging pressure sensor circuit.
Sensor electrical conformity.
Check the continuity and absence of interference resistance on the following connections:
For Mégane II and Scénic II:
– connection code 3LQ,
– connection code 3LP,
– connection code 3LN.
Between components 120 and 1071.
For Laguna II:
– connection code 3LQ,
– connection code 3LP,
– connection code 3LN.
Between components 120 and 1474.
If any of the connections are faulty and there is a repair method (see Technical Note 6015A, Electrical wiring
repair, Wiring: precautions for repairs), repair the wiring; otherwise replace the wiring.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_PR041/EDC16_V58_PR041/EDC16_V5C_PR041/EDC16_V18_PR041/EDC16_V1C_PR041/EDC16_V20_PR041

13B-232
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
*OCR: * Opening Cycle RatioPR047
TURBO PRESSURE OCR*
PARAMETER
DEFINITIONThis parameter indicates the turbocharger pressure opening cyclic ratio in %.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Engine running, engine coolant temperature > 80°C.
The value must be between 60% < PR047 < 90%.
The Opening Cyclic Ratio should be identical to the correction of the solenoid valve position
Conformity check with engine stopped and ignition on.
This value must be PR047 < 5%.
The Opening Cyclic Ratio should be identical to the correction of the solenoid valve position
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR047/EDC16_V58_PR047/EDC16_V5C_PR047/EDC16_V18_PR047/EDC16_V1C_PR047/EDC16_V20_PR047

13B-233
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
*OCR: Opening cyclic ratioPR048
RAIL PRESSURE REGULATION VALVE OCR*
PARAMETER
DEFINITIONThis parameter indicates the turbocharger pressure opening cyclic ratio in %.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Engine running, engine coolant temperature > 80°C.
The value must be between 35% < PR048 < 45%
In the event of a fault, consult the interpretation of fault DF007 Rail pressure sensor circuit.
Engine stopped, ignition on.
The value must be PR048 = 15%.
In the event of a fault, consult the interpretation of faults DF007 Rail pressure sensor circuit and DF053 Rail
pressure regulation function.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR048/EDC16_V58_PR048/EDC16_V5C_PR048/EDC16_V18_PR048/EDC16_V1C_PR048/EDC16_V20_PR048

13B-234
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR051
EGR VALVE POSITION FEEDBACK
PARAMETER
DEFINITIONThis parameter indicates the EGR valve opening ratio.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
No faults should be present or stored.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (loss of power, smoke etc.).
– after interpretation of command AC103 EGR by-pass.
Conformity check with engine stopped and ignition on.
The value must be between – 10% < PR051 < 0%.
In the event of a fault, consult the interpretation of fault DF118 EGR solenoid valve servo-control.
Engine running, engine coolant temperature > 80°C.
The value must be between 10% < PR051 < 40%.
In the event of a fault, consult the interpretation of fault DF118 EGR solenoid valve servo-control.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR051/EDC16_V58_PR051/EDC16_V5C_PR051/EDC16_V18_PR051/EDC16_V1C_PR051/EDC16_V20_PR051

13B-235
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR053
SPEED REQUESTED BY HEATING/AIR CONDITIONING
PARAMETER
DEFINITIONThis parameter indicates the engine's speed of rotation with air conditioning in rpm.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine running, engine coolant temperature > 80°C.
The engine speed requested by the air conditioning is increased and fluctuates around 875 rpm.
This parameter is only valid when the engine has been started.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR053/EDC16_V58_PR053/EDC16_V5C_PR053/EDC16_V18_PR053/EDC16_V1C_PR053/EDC16_V20_PR053

13B-236
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR055
ENGINE SPEED
PARAMETER
DEFINITIONThis parameter indicates the engine's rotational speed in rpm.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on.
With the ignition on the value is: PR055 = 0 rpm.
In the event of a fault, refer to the interpretation for fault DF005 Engine speed sensor circuit.
Conformity check with engine running, engine coolant temperature > 80°C.
With the engine idling, the value is approximately 800 rpm.
In the event of a fault, refer to the interpretation for fault DF005 Engine speed sensor circuit.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR055/EDC16_V58_PR055/EDC16_V5C_PR055/EDC16_V18_PR055/EDC16_V1C_PR055/EDC16_V20_PR055

13B-237
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR058
PR059
INLET AIR TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the inlet air temperature in °C.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
No faults should be present or stored.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (e.g. lack of power).
Conformity check with engine stopped and ignition on.
With the ignition on the inlet air temperature varies according to the exterior temperature.
Default value: 20°C
In the event of a fault, refer to the interpretation for DF039 Inlet air temperature circuit sensor
Parameter PR059 ≈ PR064 Coolant temperature cold engine.
Conformity check with engine running, engine coolant temperature > 80°C.
With the engine running at idle speed the inlet air temperature varies according to the engine coolant
temperature.
Default value: 20°C
In the event of a fault, refer to the interpretation for DF039 Inlet air temperature circuit sensor
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR058/EDC16_V58_PR058/EDC16_V5C_PR058/EDC16_V50_PR059/EDC16_V58_PR059/EDC16_V5C_PR059/
EDC16_V18_PR058/EDC16_V1C_PR058/EDC16_V20_PR058/EDC16_V18_PR059/EDC16_V1C_PR059/EDC16_V20_PR059

13B-239
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR061
EXTERIOR AIR TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the exterior air temperature in °C.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
No faults should be present or stored.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (e.g. lack of power).
Conformity check with engine running, engine coolant temperature > 80°C.
This parameter indicates the exterior air temperature in °C.
This parameter is controlled by the UCH and transmitted to the injection on the multiplex network.
Default value = 20°C
In the event of a fault, consult the UCH (see 87B, Passenger compartment connection unit).
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_PR061/EDC16_V58_PR061/EDC16_V5C_PR061

13B-240
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR064
COOLANT TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the engine coolant temperature in °C.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
No faults should be present or stored.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (e.g. lack of power).
Conformity check with engine stopped and ignition on.
With the ignition on the coolant temperature varies according to the exterior temperature.
Safe value: 119°C
In the event of a fault, consult the interpretation of fault DF001 Coolant temperature sensor circuit.
Parameter PR059: Inlet air temperature ≈ PR064 cold engine.
Conformity check with engine running, engine coolant temperature > 80°C.
With the engine running at idle speed the coolant temperature varies according to the engine temperature.
Safe value: 119°C
In the event of a fault, refer to the interpretation of DF001 Coolant temperature sensor circuit.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_PR064/EDC16_V58_PR064/EDC16_V5C_PR064/EDC16_V18_PR064/EDC16_V1C_PR064/EDC16_V20_PR064