Diagram RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16C36 Workshop Manual

13B-232V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET144HIGH-SPEED FAN ASSEMBLY RELAY CONTROL
STATUS DEFINITIONThis status indicates whether the high speed fan assembly is active.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Use the Mégane II ph2, Scénic II ph2 Technical Note wiring diagram.
Conformity check with engine stopped and ignition on
INACTIVEEngine cold and air conditioning switched off
EDC16C36_V44_ET144/EDC16C36_V4C_ET144/EDC16C36_V48_ET144/EDC16C36_V50_ET144/EDC16C36_V54_ET144/
EDC16C36_V58_ET144
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-233V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET144
CONTINUED
Conformity check with engine running, engine coolant temperature > 80°C
(heating and air-conditioning off) INACTIVE OR ACTIVE, depending on the engine temperature.
ACTIVEWhen the coolant reaches 102°C, the injection computer commands the low-speed
relay of the fan assembly and status ET144 becomes ACTIVE. The relay then
supplies the cooling fan.
If status ET144 is ACTIVE, but the cooling fan is not running, perform the following
operations:
– Check the condition of fuse FM15 (60 A) in the engine fuse and relay box.
– Disconnect the high speed relay of the fan assembly, check it is functioning correctly
and the status of the connectors of the relay mounting (see Wiring Diagram
Technical Note, Mégane II ph2, Scénic II ph2, Component code 597).
If the connector or connectors are faulty and if there is a repair procedure (see
Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the connector. Otherwise replace the wiring.
Check for the supply of + 12 V after the relay to the high-speed fan assembly relay:
– connection 3FB of component 234.
Check the continuity and the absence of interference resistance on the following
connection:
– connection code 3JP between components 234 and 120.
Check the continuity and the absence of interference resistance on the following
connection:
– Connection code 49B between components 234 and 262.
Check that the earth is in order on the MAS connection of component 262.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring. Otherwise replace the wiring.
INACTIVEWhen the injection computer no longer requests cooling, the status ET144 changes to
INACTIVE. The fan assembly should then switch off.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-238V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET405CLUTCH PEDAL SWITCH
STATUS DEFINITIONACTIVE: This status indicates that the clutch pedal is depressed.
INACTIVE: This status indicates that the clutch pedal is released.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Use the Mégane II ph2, Scénic II ph2 Technical Note wiring diagram.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C
ACTIVEClutch pedal depressed.
Non-conformity of the brake signals and/or the clutch switch signals can cause the
engine to race during gear changes.
In the event of a fault, check the electrical conformity of the sensor.
INACTIVEClutch pedal released.
Non-conformity of the brake signals and/or the clutch switch signals can cause the
engine to race during gear changes.
In the event of a fault, check the electrical conformity of the sensor.
EDC16C36_V44_ET405/EDC16C36_V4C_ET405/EDC16C36_V48_ET405/EDC16C36_V50_ET405/EDC16C36_V54_ET405/
EDC16C36_V58_ET405
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-249V9 MR-372-J84-13B450$132.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703CRUISE CONTROL/SPEED LIMITER BUTTONS
STATUS DEFINITIONRESUME: R button pressed.
SUSPEND: 0 button pressed.
INCREASE: Increase button pressed.
DECREASE: Decrease button pressed.
INACTIVE: This status indicates that no button has been pressed.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Use the Mégane II ph2, Scénic II ph2 Technical Note wiring diagram.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
INACTIVEWhen that no button has been pressed.
In the event of a fault, consult the interpretation of status ET703.
SUSPEND'0' button pressed.
In the event of a fault, consult the interpretation of status ET703.
RESUMER button pressed.
In the event of a fault, consult the interpretation of status ET703.
EDC16C36_V44_ET703/EDC16C36_V4C_ET703/EDC16C36_V48_ET703/EDC16C36_V50_ET703/EDC16C36_V54_ET703/
EDC16C36_V58_ET703
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-253V9 MR-372-J84-13B450$132.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET704
ET705BRAKE SWITCH NO. 1BRAKE SWITCH NO. 2
STATUS DEFINITIONACTIVE: This status indicates that the brake pedal is depressed.
INACTIVE: This status indicates that the brake pedal is released.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Note:
Statuses ET704 and ET705 should change status at the same time. If they are
inconsistent, consult the interpretation of fault DF228 Brake signal.
Use the Mégane II ph2, Scénic II ph2 Technical Note wiring diagram.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
ACTIVEBrake pedal depressed.
A brake signal non-conformity may cause the engine to race during gear changes.
In the event of a fault, apply the interpretation of statuses ET704 Brake contact no. 1
and ET705 Brake contact no. 2.
INACTIVEBrake pedal released.
A brake signal non-conformity may cause the engine to race during gear changes.
In the event of a fault, apply the interpretation of statuses ET704 Brake contact no.1
and ET705 Brake contact no. 2.
EDC16C36_V44_ET704/EDC16C36_V4C_ET704/EDC16C36_V48_ET704/EDC16C36_V50_ET704/EDC16C36_V54_ET704/
EDC16C36_V58_ET704/EDC16C36_V44_ET705/EDC16C36_V4C_ET705/EDC16C36_V48_ET705/EDC16C36_V50_ET705/
EDC16C36_V54_ET705/EDC16C36_V58_ET705
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-272
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR030ACCELERATOR PEDAL POSITION
PARAMETER
DEFINITIONThis parameter indicates the accelerator pedal position as a percentage.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
There must be no present or stored faults.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (e.g. lack of power, etc.).
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
If no pressure is being applied to the pedal PR030 = 0%
In the event of a fault, consult the interpretation of fault DF196 Pedal sensor gang 1 circuit or
DF198 Pedal sensor circuit gang 2.
EDC16C36_V44_PR030/EDC16C36_V4C_PR030/EDC16C36_V48_PR030/EDC16C36_V50_PR030/EDC16C36_V54_PR030/
EDC16C36_V58_PR030EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-276
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR038RAIL PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the rail pressure in bar.
NOTESThere must be no present or stored faults.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (starting faults, poor performance, stalling etc.),
– after interpretation of command AC225 Rail pressure regulator.
Special notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
Conformity check with engine stopped and ignition on
The rail pressure value is:
0 bar < PR038 < 90 bar if the coolant temperature < 30°C
In the event of a fault, consult the interpretation of fault DF007 Rail pressure sensor circuit.
Conformity check with engine running, engine coolant temperature > 80°C
The rail pressure value is:
At idle speed: PR038 = 270 bar ± 20 bar
Full load: PR038 = 1700 bar ± 20 bar
In the event of a fault, consult the interpretation of fault DF007 Rail pressure sensor circuit.
EDC16C36_V44_PR038/EDC16C36_V4C_PR038/EDC16C36_V48_PR038/EDC16C36_V50_PR038/EDC16C36_V54_PR038/
EDC16C36_V58_PR038EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-277
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR038
CONTINUED
Sensor electrical conformity
Check the status of the connector of the rail pressure sensor (see Wiring Diagram Technical Note, Mégane II
ph2, Scénic II ph2, Component code 1032).
Check the status of the connector of the rail pressure sensor (see Wiring Diagram Technical Note, Mégane II
ph2, Scénic II ph2, Component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity and absence of interference resistance on the following connections:
– Connection code 3LX,
– Connection code 3LY,
– Connection code 3LZ,
between components 120 and 1032.
If any of the connections are faulty and there is a repair method (see Technical Note 6015A, Electrical wiring
repair, Wiring: precautions for repairs), repair the wiring; otherwise replace the wiring.
Check that there is no external diesel leak from the high pressure fuel circuit.
With the ignition on and the engine stopped for over 1 minute:
Display parameter PR038.
– If the pressure is below 90 bar, the sensor is in order.
– If the pressure is above 90 bar, contact the Techline.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-278
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR041TURBOCHARGING PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the turbocharging pressure in mbar.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The turbocharging pressure value is PR041 = PR035 ± 0.20 bar
In the event of a fault, consult the interpretation of DF004 Turbocharging pressure sensor circuit.
EDC16C36_V44_PR041/EDC16C36_V4C_PR041/EDC16C36_V48_PR041/EDC16C36_V50_PR041/EDC16C36_V54_PR041/
EDC16C36_V58_PR041EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-282
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR051EGR VALVE POSITION FEEDBACK
PARAMETER
DEFINITIONThis parameter indicates the EGR valve opening ratio.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
There must be no present or stored faults.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (loss of power, smoke etc.).
– after interpretation of command AC103 EGR by-pass.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
This parameter indicates the EGR valve opening ratio.
In the event of a fault, consult the interpretation of faults DF209 EGR valve position sensor circuit and DF647
EGR valve position regulation.
EDC16C36_V44_PR051/EDC16C36_V4C_PR051/EDC16C36_V48_PR051/EDC16C36_V50_PR051/EDC16C36_V54_PR051/
EDC16C36_V58_PR051EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58